the dmesg command:
- Code: Select all
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xe0800000 - 0xfe800000 ( 480 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0031000 ( 164 kB)
.text : 0xc0031000 - 0xc064c000 (6252 kB)
.data : 0xc064c000 - 0xc0678f80 ( 180 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:114
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Kirkwood: MV88F6281-A1, TCLK=166666667.
Feroceon L2: Enabling L2
Feroceon L2: Cache support initialised.
initial MPP regs: 01112222 00003311 33331100 33003333 00000033 00000000 00000000
final MPP regs: 01112222 00003311 33331100 33003333 00000033 00000000 00000000
orion-ehci registered
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 32
NetWinder Floating Point Emulator V0.97 (double precision)
Switched to NOHz mode on CPU #0
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Registering unionfs 2.5.11 (for 2.6.39.4)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
NTFS driver 2.1.30 [Flags: R/W].
fuse init (API version 7.16)
JFS: nTxBlock = 4007, nTxLock = 32063
SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
SGI XFS Quota Management subsystem
msgmni has been set to 1001
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
console [ttyS0] enabled
loop: module loaded
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 21
ata2: SATA max UDMA/133 irq 21
m25p80 spi0.0: mx25l4005a (512 Kbytes)
Creating 2 MTD partitions on "spi_flash":
0x000000000000-0x00000007d000 : "u-boot"
0x00000007e000-0x00000007f000 : "u-boot-env"
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:91:8c:3d
mv643xx_eth_port mv643xx_eth_port.1: eth1: port 0 with MAC address 00:d0:4b:91:8c:3e
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
usbcore: registered new interface driver pegasus
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
i2c /dev entries driver
at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
Registered led device: net5big-v2:blue:power
Registered led device: net5big-v2:red:power
Registered led device: net5big-v2:blue:sata0
Registered led device: net5big-v2:red:sata0
Registered led device: net5big-v2:blue:sata1
Registered led device: net5big-v2:red:sata1
Registered led device: net5big-v2:blue:sata2
Registered led device: net5big-v2:red:sata2
Registered led device: net5big-v2:blue:sata3
Registered led device: net5big-v2:red:sata3
Registered led device: net5big-v2:blue:sata4
Registered led device: net5big-v2:red:sata5
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (8015 buckets, 32060 max)
IPv4 over IPv4 tunneling driver
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
NET: Registered protocol family 10
ip6_tables: (C) 2000-2006 Netfilter Core Team
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 37
VFP support v0.3: not present
Gating clock of unused units
before: 0x00cfc1dd
after: 0x00cfc1c9
rtc-mv rtc-mv: setting system clock to 2012-07-20 06:34:44 UTC (1342766084)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
ata1.00: hard resetting link
ata1.01: hard resetting link
ata1.02: hard resetting link
ata1.03: hard resetting link
ata1.03: ATA-8: WDC WD5000AAKX-08ERMA0, 19.01H19, max UDMA/100
ata1.03: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.03: configured for UDMA/100
ata1: EH complete
scsi 0:3:0:0: Direct-Access ATA WDC WD5000AAKX-0 19.0 PQ: 0 ANSI: 5
sd 0:3:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 0:3:0:0: [sda] Write Protect is off
sd 0:3:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:3:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:3:0:0: [sda] Attached SCSI disk
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata2.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
ata2.00: hard resetting link
ata2.01: hard resetting link
ata2.02: hard resetting link
ata2.03: hard resetting link
ata2: EH complete
md: Waiting for all devices to be available before autodetect
md: If you don't use raid, use raid=noautodetect
md: Autodetecting RAID arrays.
md: Scanned 0 and added 0 devices.
md: autorun ...
md: ... autorun DONE.
EXT3-fs (sda7): recovery required on readonly filesystem
EXT3-fs (sda7): write access will be enabled during recovery
EXT3-fs: barriers not enabled
EXT3-fs (sda7): recovery complete
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
Freeing init memory: 164K
EXT3-fs (sda7): using internal journal
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Marvell Orion EHCI
usb usb1: Manufacturer: Linux 2.6.39.4 ehci_hcd
usb usb1: SerialNumber: orion-ehci.0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver usblp
iSCSI Enterprise Target Software - version trunk
iscsi_trgt: Registered io type fileio
iscsi_trgt: Registered io type blockio
iscsi_trgt: Registered io type nullio
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
usb 1-1: new high speed USB device number 2 using orion-ehci
usb 1-1: New USB device found, idVendor=0424, idProduct=2512
usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
hub 1-1:1.0: USB hub found
hub 1-1:1.0: 2 ports detected
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 100 Mb/s, full duplex, flow control disabled
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
udevd (846): /proc/846/oom_adj is deprecated, please use /proc/846/oom_score_adj instead.
eth0: no IPv6 routers present
root@fvdwsl-base:/ #
the mount command
- Code: Select all
login as: root
root@192.168.1.189's password:
root@fvdwsl-base:/ # mount
rootfs on / type rootfs (rw)
/dev/root on / type ext3 (rw,relatime,errors=continue,barrier=0,data=ordered)
none on /proc type proc (rw,relatime)
none on /sys type sysfs (rw,relatime)
/dev/sda5 on /rw_fs type ext3 (rw,noatime,errors=continue,barrier=0,data=ordered)
tmpfs on /rw_fs/tmp/usr/var type tmpfs (rw,relatime,size=5000k)
/dev/sda8 on /share/1000 type ext3 (rw,relatime,errors=continue,barrier=0,data=ordered)
root@fvdwsl-base:/ #
and the last command:
- Code: Select all
login as: root
root@192.168.1.189's password:
root@fvdwsl-base:/ # cat boot.log
start boot log
booting using root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
buttons-nwsp2 daemon started
Fri Jul 20 07:34:48 GMT+1 2012
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
starting php based setup routines step 1
* Initial XML configuration file... [ OK ]
* Configuring Disks... [ OK ]
* Configuring System Users...
Root password: use default password
Set users, linux and samba accounts [ OK ]
* Starting mount of volumes...
- Mounting volume Default: [ OK ]
* Finishing mount of volumes... [ OK ]
* Generating Hosts File... [ OK ]
* Configuring System Hostname... [ OK ]
* Configuring Samba... [ OK ]
* Configuring LAN interface... [ OK ]
* Starting udevd... [ OK ]
* Starting web server... [ OK ]
* Initializing Timezone... [ OK ]
* Configuring Samba... [ OK ]
* Starting syncawayd... [ OK ]
start portmap service
starting php based setup routines step 2
* Starting dropbear... [ OK ]
* Kill temporary dropbear... [ OK ]
* Starting daemon update Hosts File... [ OK ]
starting php based setup routines step banner
*** fvdw-sl NAS firmware
This is fvdw-sl version: fvdw-sl 14.0
built on: December 23 2012
LAN IP address: 192.168.1.189 (DHCP)
Port configuration:
LAN -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
rcS finished
root@fvdwsl-base:/ #
