Try to Get a Disk Image of Drive of 2Big V2

[RedSun]

Sorry but you still stop the nas before it runs user script (cronbootscript.sh) and you posted the previous output of eth0.log

So attached a new version.
With it eth0.log is deleted before writing the new outputs and you have to wait now up to front led is red. Then you have to unplug/plug the network cable at this step (you have 10'' to do it). Stop the NAS when front led is blue again

This is where we disconnect. I never see any red. The front LED is just blue, then solid blue. Never any red, as I recall.

[RedSun]

At boot time. It has flashing blue, then turn to solid. That is silent. Then it stays at solid blue, fan starts running. It just sits there with fan running. Ethernet mostly dark and tries to connect from time to time. My giga network only turns on amber/yellow. Not the typical green. So very limited activity.

[Jocko]

Please note that the boot sequence lasts at least 2 minutes.
So, skip the unplug/plug check and wait 2-3 minutes before stopping and opening telnet access.

[RedSun]

Yes, this is what I've been doing. For normal boot, I always boot it fully and wait for much longer. Then I power off and connect to the fvdw console and telnet.

I never see red with fvdw-sl builds.

[Jocko]

Ok but Im still waiting outputs (boot. Log and eth0. Log) with the last version of the script I sent you previously. What you posted was not correct.

[RedSun]

Sorry but you still stop the nas before it runs user script (cronbootscript.sh) and you posted the previous output of eth0.log

So attached a new version.
With it eth0.log is deleted before writing the new outputs and you have to wait now up to front led is red. Then you have to unplug/plug the network cable at this step (you have 10'' to do it). Stop the NAS when front led is blue again

I'm not sure exactly what you meant about the 5'' and 10''. Are they 5 seconds and 10 seconds?

When my box boots, front LED flashes blue, fan not running, network LED flashes briefly. Then HD starts to spin, network LED flashes rapidly and fan starts to run. After several seconds, front LED become solid blue. That is the final state of regular boot. Solid front LED and fan running all time.

[RedSun]

Here is current boot.log. The network portion appears blank.

Code: Select all

root@fvdw-sta-kirkwood:/ # mkdir /sda7
root@fvdw-sta-kirkwood:/ # mount /dev/sda7 /sda7
root@fvdw-sta-kirkwood:/ # cat /sda7/boot.log
start boot log
is a physical machine
detect and set platform
2big2
kirkwood
UIMAGE-414133-KIRKWOOD-5
Current kernel: 4.14.133 #5 PREEMPT Thu Aug 10 15:38:37 CEST 2023
device 2big2
family kirkwood
Arm: found valid system disk sdb
system disk = sdb
 mount dev/pts
update dev nodes
booting using  root file system...
enable IP forwarding...
run udevstart to update dev nodes when necessary
inserting kernel modules:
modprobe: module 'iscsi_trgt' not found
start buttons control daemon
device = 2big2
source = buttons-nwsp2
buttons-nwsp2 daemon started
Sat Aug 30 21:04:42 UTC 2025
configuration partition is rightly mounted
create temporary passwd file
create temporary group file
set samba environment for version 3.0.37
configure loopback network interface
setting reboot and standby
2big2
rebootd-nwsp2
2big2
standbyd-nwsp2
start fan
starting php based setup routines step 1
 * Initialize the volatile db file...    [ OK ]
 * Starting udevd...                                     [ OK ]
 * Finishing restore RAID devices...     [ OK ]
 * Found database configuration file...  [ OK ]
 * Updating Disks database...                    [ OK ]
 * Starting mount of volumes...
   - Mounting volume Vol-B:  [ OK ]
 * Finishing mount of volumes...                 [ OK ]
 * Generating Hosts File...                      [ OK ]
 * Configuring System Hostname...                [ OK ] 
 * Configuring LAN interface...                  [ OK ]
 * Initializing Timezone...                      [ OK ]
 * Starting web server...                                [ OK ]
 * Starting mount of internal USB ...
 * Finishing mount internal USB ...      [ OK ]
 * Configuring Disks...                                  [ OK ]
 * Configuring Samba...                                  [ OK ]
 * Configuring System Users...
        Root password: use default password
        Set users, linux and samba accounts      [ OK ]
 * Starting Fvdw-sl Discovery Daemon...  [ OK ]
start rpcbind service
starting php based setup routines step 2
 * Starting dropbear...                                  [ OK ]
 * Kill temporary dropbear...                    [ OK ]
starting php based setup routines step 3
 * Starting daemon update Hosts File...  [ OK ]
 * Starting mount of remote shares...
 * Finishing mount shares...                     [ OK ]
starting php based setup routines step banner


*** fvdw-sl NAS firmware
    This is fvdw-sl version: fvdw-sl 18.3
    built on: February 20 2024

    LAN IP address:  (DHCP)

    Port configuration:

    LAN   -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
move smbd en nmbd db files away from ram disk to prevent hanging samba server
root@fvdw-sta-kirkwood:/ #

[RedSun]

And the eth0.log. Again, the static IP address is gone.

Code: Select all

root@fvdw-sta-kirkwood:/ # cat /sda7/eth0.log
*******************************************
 dmesg output
*******************************************
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 4.14.133 (root@fvdwsl-5big2.local) (gcc version 4.9.3 (GCC)) #5 PREEMPT Thu Aug 10 15:38:37 CEST 2023
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=0005317f
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie 2Big Network v2
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 65536
[    0.000000] free_area_init_node: node 0, pgdat c0929960, node_mem_map cfdfa000
[    0.000000]   Normal zone: 512 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 65536 pages, LIFO batch:15
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 65024
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sdb7 ro reset=0 productType=PRO_KW
[    0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)
[    0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
[    0.000000] Memory: 250048K/262144K available (6915K kernel code, 307K rwdata, 1724K rodata, 192K init, 388K bss, 12096K reserved, 0K cma-reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xd0800000 - 0xff800000   ( 752 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xd0000000   ( 256 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06c8f94   (6916 kB)
[    0.000000]       .init : 0xc08ae000 - 0xc08de000   ( 192 kB)
[    0.000000]       .data : 0xc08de000 - 0xc092ada0   ( 308 kB)
[    0.000000]        .bss : 0xc0932720 - 0xc099393c   ( 389 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000]  Tasks RCU enabled.
[    0.000000] NR_IRQS: 114
[    0.000000] Switching to timer-based delay loop, resolution 6ns
[    0.000008] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 12884901885ns
[   22.305608] clocksource: orion_clocksource: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 11467562657 ns
[   22.305905] Console: colour dummy device 80x30
[   22.305941] Calibrating delay loop (skipped), value calculated using timer frequency.. 333.33 BogoMIPS (lpj=1666666)
[   22.305964] pid_max: default: 32768 minimum: 301
[   22.306114] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   22.306139] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   22.306678] CPU: Testing write buffer coherency: ok
[   22.307524] Setting up static identity map for 0x81e0 - 0x8238
[   22.307704] Hierarchical SRCU implementation.
[   22.309596] random: get_random_u32 called from bucket_table_alloc+0x14c/0x198 with crng_init=0
[   22.310008] VFP support v0.3: not present
[   22.310272] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[   22.310303] futex hash table entries: 256 (order: -1, 3072 bytes)
[   22.310409] xor: measuring software checksum speed
[   22.406016]    arm4regs  :  1088.400 MB/sec
[   22.505685]    8regs     :   653.200 MB/sec
[   22.605691]    32regs    :   904.400 MB/sec
[   22.605710] xor: using function: arm4regs (1088.400 MB/sec)
[   22.605727] pinctrl core: initialized pinctrl subsystem
[   22.606338] NET: Registered protocol family 16
[   22.606868] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   22.609475] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   22.609506] Feroceon L2: Enabling L2
[   22.609545] Feroceon L2: Cache support initialised.
[   22.610315] kirkwood_init: create proc tsinfo proc
[   22.610338] tsinfo: create proc tsinfo vendor successfully
[   22.610346] mv_usb_init 1
[   22.610357] mv_usb_init 2 devnum = 0
[   22.610368] init function mv_usb_init finished
[   22.610377] initial MPP regs:
[   22.610381]  01112222
[   22.610385]  00003311
[   22.610392]  00551100
[   22.610399]  00000000
[   22.610405]  00000000
[   22.610412]  00000000
[   22.610418]  00000000
[   22.610425]
[   22.610440]   final MPP regs:
[   22.610443]  01112222
[   22.610447]  00003311
[   22.610453]  00551100
[   22.610460]  00000000
[   22.610466]  00000000
[   22.610472]  00000000
[   22.610479]  00000000
[   22.610485]
[   22.610868]  orion-ehci registered
[   22.613180] orion_gpio_is_valid: invalid GPIO 7
[   22.613959] Kirkwood PCIe port 0: link down
[   22.613973] Kirkwood PCIe port 1: link up
[   22.613988] PCI: bus0 uses PCIe port 0
[   22.614267] PCI host bridge to bus 0000:00
[   22.614290] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   22.614305] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   22.614318] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   22.614354] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[   22.614388] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[   22.614402] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x0fffffff]
[   22.614469] pci 0000:00:00.0: supports D1 D2
[   22.615012] PCI: bus0: Fast back to back transfers disabled
[   22.615034] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[   22.615042] PCI: bus1 uses PCIe port 1
[   22.615348] PCI host bridge to bus 0000:01
[   22.615367] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[   22.615381] pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
[   22.615392] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[   22.615424] PCI: bus1: Fast back to back transfers enabled
[   22.615438] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   22.816733] raid6: int32x1  gen()   101 MB/s
[   22.986101] raid6: int32x1  xor()    63 MB/s
[   23.156071] raid6: int32x2  gen()   133 MB/s
[   23.325843] raid6: int32x2  xor()    84 MB/s
[   23.495839] raid6: int32x4  gen()   133 MB/s
[   23.665891] raid6: int32x4  xor()    90 MB/s
[   23.835869] raid6: int32x8  gen()   121 MB/s
[   24.005750] raid6: int32x8  xor()    80 MB/s
[   24.005760] raid6: using algorithm int32x2 gen() 133 MB/s
[   24.005769] raid6: .... xor() 84 MB/s, rmw enabled
[   24.005777] raid6: using intx1 recovery algorithm
[   24.006070] vgaarb: loaded
[   24.006602] SCSI subsystem initialized
[   24.006917] libata version 3.00 loaded.
[   24.007438] usbcore: registered new interface driver usbfs
[   24.007555] usbcore: registered new interface driver hub
[   24.007682] usbcore: registered new device driver usb
[   24.007947] Linux video capture interface: v2.00
[   24.010604] clocksource: Switched to clocksource orion_clocksource
[   24.010733] VFS: Disk quotas dquot_6.6.0
[   24.010793] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   24.025376] NET: Registered protocol family 2
[   24.026638] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[   24.026680] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[   24.026714] TCP: Hash tables configured (established 2048 bind 2048)
[   24.026802] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   24.026829] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   24.026984] NET: Registered protocol family 1
[   24.027335] RPC: Registered named UNIX socket transport module.
[   24.027349] RPC: Registered udp transport module.
[   24.027357] RPC: Registered tcp transport module.
[   24.027365] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   24.027392] PCI: CLS 32 bytes, default 32
[   24.027627] NetWinder Floating Point Emulator V0.97 (double precision)
[   24.027760] gpio-usb-probe-1
[   24.027825] gpio-usb-probe-4b err=0
[   24.027841] gpio-usb gpio-usb: USB GPIO's initialized
[   24.029517] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[   24.030149] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   24.030531] ntfs: driver 2.1.32 [Flags: R/W].
[   24.030571] jffs2: version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
[   24.030721] fuse init (API version 7.26)
[   24.031006] JFS: nTxBlock = 1953, nTxLock = 15628
[   24.032084] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[   24.037677] async_tx: api initialized (async)
[   24.037759] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[   24.037772] io scheduler noop registered
[   24.037781] io scheduler deadline registered
[   24.037835] io scheduler cfq registered (default)
[   24.037846] io scheduler mq-deadline registered
[   24.038102] mv_xor mv_xor.0: Marvell shared XOR driver
[   24.096344] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[   24.098438] mv_xor mv_xor.1: Marvell shared XOR driver
[   24.156342] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[   24.163206] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   24.165386] console [ttyS0] disabled
[   24.185791] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   24.876563] random: fast init done
[   24.916607] console [ttyS0] enabled
[   24.933238] brd: module loaded
[   24.943288] loop: module loaded
[   24.947696] sata_mv sata_mv.0: version 1.28
[   24.947764] sata_mv sata_mv.0: cannot get optional clkdev
[   24.953241] sata_mv sata_mv.0: slots 32 ports 2
[   24.961564] scsi host0: sata_mv
[   24.965280] scsi host1: sata_mv
[   24.968825] ata1: SATA max UDMA/133 irq 21
[   24.972911] ata2: SATA max UDMA/133 irq 21
[   24.978468] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[   24.984346] Creating 2 MTD partitions on "spi_flash":
[   24.989455] 0x000000000000-0x00000007d000 : "u-boot"
[   24.995304] 0x00000007e000-0x00000007f000 : "u-boot-env"
[   25.003274] tun: Universal TUN/TAP device driver, 1.6
[   25.009600] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   25.017843] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   25.034123] libphy: orion_mdio_bus: probed
[   25.038459] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   25.315673] ata1: SATA link down (SStatus 0 SControl F300)
[   25.837050] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:8e:fd:e6
[   25.846038] PPP generic driver version 2.4.2
[   25.850660] PPP Deflate Compression module registered
[   25.855800] PPP MPPE Compression module registered
[   25.860573] NET: Registered protocol family 24
[   25.865017] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[   25.872535] usbcore: registered new interface driver pegasus
[   25.878434] usbcore: registered new interface driver asix
[   25.883997] usbcore: registered new interface driver ax88179_178a
[   25.890201] usbcore: registered new interface driver cdc_ether
[   25.896194] usbcore: registered new interface driver net1080
[   25.902017] usbcore: registered new interface driver plusb
[   25.907659] usbcore: registered new interface driver cdc_subset
[   25.913739] usbcore: registered new interface driver zaurus
[   25.919483] usbcore: registered new interface driver ipheth
[   25.925229] usbcore: registered new interface driver cdc_ncm
[   25.931609] aoe: cannot create debugfs directory
[   25.936720] aoe: AoE v85 initialised.
[   25.940790] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   25.947022] i2c /dev entries driver
[   25.952026] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[   25.959174] uvcvideo: Unable to create debugfs directory
[   25.964827] usbcore: registered new interface driver uvcvideo
[   25.970706] USB Video Class driver (1.1.1)
[   25.974784] gspca_main: v2.14.0 registered
[   25.979089] usbcore: registered new interface driver Philips webcam
[   25.995938] gpio-fan gpio-fan: GPIO fan initialized
[   26.001843] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[   26.010831] device-mapper: multipath round-robin: version 1.2.0 loaded
[   26.017438] device-mapper: multipath queue-length: version 0.2.0 loaded
[   26.024024] device-mapper: multipath service-time: version 0.3.0 loaded
[   26.030744] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   26.036847] device-mapper: raid: Loading target version 1.13.0
[   26.044521] Netfilter messages via NETLINK v0.30.
[   26.050095] nfnl_acct: registering with nfnetlink.
[   26.054973] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[   26.061012] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   26.067837] ipip: IPv4 and MPLS over IPv4 tunneling driver
[   26.074467] ata2.15: Port Multiplier 1.1, 0x197b:0x2352 r1, 2 ports, feat 0x0/0x8
[   26.082470] ip_tables: (C) 2000-2006 Netfilter Core Team
[   26.090885] NET: Registered protocol family 10
[   26.099653] ata2.00: hard resetting link
[   26.105336] Segment Routing with IPv6
[   26.109743] ip6_tables: (C) 2000-2006 Netfilter Core Team
[   26.115385] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[   26.122378] NET: Registered protocol family 17
[   26.127221] Bridge firewalling registered
[   26.131434] NET: Registered protocol family 5
[   26.136861] console [netcon0] enabled
[   26.140509] netconsole: network logging started
[   26.145737] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   26.152763] rtc-mv rtc-mv: setting system clock to 2025-08-30 21:04:37 UTC (1756587877)
[   26.466381] ata2.01: hard resetting link
[   27.135698] ata2.00: ATA-7: ST3320620AS, 3.AAJ, max UDMA/133
[   27.141336] ata2.00: 625142448 sectors, multi 0: LBA48
[   27.215716] ata2.00: configured for UDMA/133
[   27.220188] ata2: EH complete
[   27.235978] scsi 1:0:0:0: Direct-Access     ATA      ST3320620AS      J    PQ: 0 ANSI: 5
[   27.244580] fvdw1 disk index before get_sd_name = 0
[   27.249594] device-name= sata_mv
[   27.252807] fvdw2 disk index after get_sd_name = 1
[   27.257615] fvdw3 prefix[0]=s  prefix[1]=d
[   27.261696] fvdw4 diskname = sdb
[   27.265413] sd 1:0:0:0: [sdb] 625142448 512-byte logical blocks: (320 GB/298 GiB)
[   27.273562] sd 1:0:0:0: [sdb] Write Protect is off
[   27.278424] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[   27.278541] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   27.336293]  sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
[   27.344273] sd 1:0:0:0: [sdb] Attached SCSI disk
[   27.349447] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[   27.368840] EXT4-fs (sdb7): mounting ext3 file system using the ext4 subsystem
[   27.376446] EXT4-fs (sdb7): INFO: recovery required on readonly filesystem
[   27.383289] EXT4-fs (sdb7): write access will be enabled during recovery
[   28.036490] EXT4-fs (sdb7): recovery complete
[   28.135743] EXT4-fs (sdb7): mounted filesystem with ordered data mode. Opts: (null)
[   28.143407] VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
[   28.150626] Freeing unused kernel memory: 192K
[   28.155046] This architecture does not have kernel memory protection.
[   29.145765] EXT4-fs (sdb7): re-mounted. Opts: (null)
[   30.636824] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   30.643905] ehci-orion: EHCI orion driver
[   30.648131] orion-ehci orion-ehci.0: EHCI Host Controller
[   30.653534] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   30.661309] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   30.695659] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   30.701710] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   30.708490] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   30.715690] usb usb1: Product: EHCI Host Controller
[   30.720550] usb usb1: Manufacturer: Linux 4.14.133 ehci_hcd
[   30.726134] usb usb1: SerialNumber: orion-ehci.0
[   30.731115] hub 1-0:1.0: USB hub found
[   30.734878] hub 1-0:1.0: 1 port detected
[   30.757735] usbcore: registered new interface driver usb-storage
[   30.779348] usbcore: registered new interface driver usblp
[   30.821020] Loading iSCSI transport class v2.0-870.
[   30.830485] iscsi: registered transport (tcp)
[   31.127778] EXT4-fs (sdb5): mounting ext3 file system using the ext4 subsystem
[   31.256029] EXT4-fs (sdb5): 1 orphan inode deleted
[   31.260809] EXT4-fs (sdb5): recovery complete
[   31.505752] EXT4-fs (sdb5): mounted filesystem with ordered data mode. Opts: (null)
[   31.624281] random: mkswap: uninitialized urandom read (16 bytes read)
[   31.702906] Adding 514076k swap on /dev/sdb3.  Priority:-2 extents:1 across:514076k
[   31.794162] random: dropbear: uninitialized urandom read (32 bytes read)
[   43.902213] random: crng init done
[   44.030237] udevd (999): /proc/999/oom_adj is deprecated, please use /proc/999/oom_score_adj instead.
[   44.039588] udev: starting version 130
[   44.470247] synth uevent: /gpiochip0: failed to send uevent
[   44.470265] gpio gpiochip0: uevent: failed to send synthetic uevent
[   44.513117] synth uevent: /gpiochip1: failed to send uevent
[   44.513136] gpio gpiochip1: uevent: failed to send synthetic uevent
[   54.345074] EXT4-fs (sdb8): warning: maximal mount count reached, running e2fsck is recommended
[   54.488075] EXT4-fs (sdb8): recovery complete
[   54.525754] EXT4-fs (sdb8): mounted filesystem with ordered data mode. Opts: user_xattr,acl,nodelalloc
[   56.586499] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
*******************************************
 iface settings
*******************************************
eth0      Link encap:Ethernet  HWaddr 00:D0:4B:8E:FD:E6 
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)
          Interrupt:11

Settings for eth0:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
                                1000baseT/Full
        Advertised pause frame use: Symmetric Receive-only
        Advertised auto-negotiation: Yes
        Speed: 10Mb/s
        Duplex: Half
        Port: MII
        PHYAD: 8
        Transceiver: external
        Auto-negotiation: on
        Supports Wake-on: d
        Wake-on: d
        Link detected: no
*******************************************
 routes
*******************************************
*******************************************
 DNS
*******************************************
*******************************************
 iface kernel settings
*******************************************
/sys/class/net/eth0/addr_assign_type:0
/sys/class/net/eth0/addr_len:6
/sys/class/net/eth0/address:00:d0:4b:8e:fd:e6
/sys/class/net/eth0/broadcast:ff:ff:ff:ff:ff:ff
/sys/class/net/eth0/carrier:0
/sys/class/net/eth0/carrier_changes:6
/sys/class/net/eth0/dev_id:0x0
/sys/class/net/eth0/dev_port:0
/sys/class/net/eth0/dormant:0
/sys/class/net/eth0/duplex:half
/sys/class/net/eth0/flags:0x1003
/sys/class/net/eth0/gro_flush_timeout:0
/sys/class/net/eth0/ifindex:3
/sys/class/net/eth0/iflink:3
/sys/class/net/eth0/link_mode:0
/sys/class/net/eth0/mtu:1500
/sys/class/net/eth0/netdev_group:0
/sys/class/net/eth0/operstate:down
/sys/class/net/eth0/proto_down:0
/sys/class/net/eth0/speed:10
/sys/class/net/eth0/tx_queue_len:1000
/sys/class/net/eth0/type:1
/sys/class/net/eth0/uevent:INTERFACE=eth0
/sys/class/net/eth0/uevent:IFINDEX=3
root@fvdw-sta-kirkwood:/ #

[Jocko]

Hi

[quote="RedSun"]Here is current boot.log. The network portion appears blank.

It is the expected output as you made a new fresh install where you put only the last additional package (eth0-check.tgz ). So debug mode is disabled and the nas requests a lease for an address IP which it must get again a leasefail answer

Code: Select all

*** fvdw-sl NAS firmware
    This is fvdw-sl version: fvdw-sl 18.3
    built on: February 20 2024

    LAN IP address:  (DHCP)

    Port configuration:

    LAN   -> eth0

So you have to install again :
viewtopic.php?f=27&t=3855&start=10#p39866
viewtopic.php?f=27&t=3855&start=30#p39883

NB: following the installation order does not matter