Blue LED Blinking and no network access to 2Big Network

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:13 pm

how stop this loop ??
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:15 pm

Marvell>> setenv bootargs console=ttyS0,115200 netconsole=6666@${ipaddr}/,6666@$
{serverip}/ root=/dev/sda7
setenv bootargs console=ttyS0,115200 netconsole=6666@${ipaddr}/,6666@${serverip}
/ root=/dev/sda7
Marvell>> printenv bootargs
printenv bootargs
bootargs=console=ttyS0,115200 netconsole=6666@10.0.0.252/,6666@10.0.0.77/ root=/
dev/sda7
Marvell>> ide reset
ide reset

Reset IDE:
Marvell Serial ATA Adapter

Marvell Serial ATA Adapter
Integrated Sata device found
[0 0 0]: Enable DMA mode (5)
Device 0 @ 0 0:
Model: WDC WD40EFRX-68N32N0 Firm: 82.00A82 Ser#: WD-WCC
7K6YY01DX
Type: Hard Disk
Supports 48-bit addressing
Capacity: 3815447.8 MB = 3726.0 GB (7814037168 x 512)
PCIe SATA:ffffffff
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:19 pm

Filename 'firmware/kirkwood/UIMAGE-414133-KIRKWOOD-1'.
Load address: 0x800000
Loading: #################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#################################################################
#######################
done
Bytes transferred = 4776328 (48e188 hex)
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby fvdw » Fri Nov 18, 2022 2:20 pm

oke, now bootm
fvdw
Site Admin - expert
 
Posts: 13471
Joined: Tue Apr 12, 2011 2:30 pm
Location: Netherlands

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:25 pm

[ 3.703020] random: get_random_u32 called from bucket_table_alloc+0x14c/0x198
with crng_init=0
[ 3.703316] VFP support v0.3: not present
[ 3.703524] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma
x_idle_ns: 19112604462750000 ns
[ 3.703550] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 3.703635] xor: measuring software checksum speed
[ 3.800401] arm4regs : 1729.200 MB/sec
[ 3.900128] 8regs : 1090.000 MB/sec
[ 4.000126] 32regs : 1508.800 MB/sec
[ 4.000140] xor: using function: arm4regs (1729.200 MB/sec)
[ 4.000154] pinctrl core: initialized pinctrl subsystem
[ 4.000642] NET: Registered protocol family 16
[ 4.000985] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 4.003068] Kirkwood: MV88F6282-Rev-A1, TCLK=200000000.
[ 4.003093] Feroceon L2: Enabling L2
[ 4.003123] Feroceon L2: Cache support initialised.
[ 4.003652] kirkwood_init: create proc tsinfo proc
[ 4.003668] tsinfo: create proc tsinfo vendor successfully
[ 4.003673] mv_usb_init 1
[ 4.003680] mv_usb_init 2 devnum = 0
[ 4.003686] init function mv_usb_init finished
[ 4.003695] 01111111
[ 4.003697] 00003311
[ 4.003701] 00551100
[ 4.003705] 00000000
[ 4.003709] 00000000
[ 4.003712] 00000000
[ 4.003716] 00000000
[ 4.003720]
[ 4.003732] 01111111
[ 4.003734] 00003311
[ 4.003738] 00551100
[ 4.003741] 00000000
[ 4.003745] 00000000
[ 4.003748] 00000000
[ 4.003752] 00000000
[ 4.003755]
[ 4.003998] orion-ehci registered
[ 4.005648] Kirkwood PCIe port 0: link up
[ 4.005657] Kirkwood PCIe port 1: link down
[ 4.005666] PCI: bus0 uses PCIe port 0
[ 4.005961] PCI host bridge to bus 0000:00
[ 4.005978] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[ 4.005986] pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
[ 4.005994] pci_bus 0000:00: No busn resource found for root bus, will use [b
us 00-ff]
[ 4.006920] pci 0000:00:01.0: [Firmware Bug]: reg 0x10: invalid BAR (can't si
ze)
[ 4.006938] pci 0000:00:01.0: [Firmware Bug]: reg 0x14: invalid BAR (can't si
ze)
[ 4.006954] pci 0000:00:01.0: [Firmware Bug]: reg 0x18: invalid BAR (can't si
ze)
[ 4.006969] pci 0000:00:01.0: [Firmware Bug]: reg 0x1c: invalid BAR (can't si
ze)
[ 4.006984] pci 0000:00:01.0: [Firmware Bug]: reg 0x20: invalid BAR (can't si
ze)
[ 4.007458] PCI: bus0: Fast back to back transfers disabled
[ 4.007479] PCI: bus1 uses PCIe port 1
[ 4.007766] PCI host bridge to bus 0000:01
[ 4.007779] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[ 4.007787] pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff]
[ 4.007795] pci_bus 0000:01: No busn resource found for root bus, will use [b
us 01-ff]
[ 4.008031] PCI: bus1: Fast back to back transfers disabled
[ 4.008063] pci 0000:00:01.0: BAR 6: assigned [mem 0xe0000000-0xe000ffff pref
]
[ 4.008075] pci 0000:00:01.0: BAR 5: assigned [mem 0xe0010000-0xe00101ff]
[ 4.200796] raid6: int32x1 gen() 157 MB/s
[ 4.370262] raid6: int32x1 xor() 98 MB/s
[ 4.540320] raid6: int32x2 gen() 212 MB/s
[ 4.710297] raid6: int32x2 xor() 137 MB/s
[ 4.880181] raid6: int32x4 gen() 215 MB/s
[ 5.050220] raid6: int32x4 xor() 147 MB/s
[ 5.220205] raid6: int32x8 gen() 200 MB/s
[ 5.390287] raid6: int32x8 xor() 133 MB/s
[ 5.390293] raid6: using algorithm int32x4 gen() 215 MB/s
[ 5.390298] raid6: .... xor() 147 MB/s, rmw enabled
[ 5.390302] raid6: using intx1 recovery algorithm
[ 5.390519] vgaarb: loaded
[ 5.390898] SCSI subsystem initialized
[ 5.391464] usbcore: registered new interface driver usbfs
[ 5.391544] usbcore: registered new interface driver hub
[ 5.391631] usbcore: registered new device driver usb
[ 5.391813] Linux video capture interface: v2.00
[ 5.393289] clocksource: Switched to clocksource orion_clocksource
[ 5.393387] VFS: Disk quotas dquot_6.6.0
[ 5.393432] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 5.403069] NET: Registered protocol family 2
[ 5.403553] TCP established hash table entries: 2048 (order: 1, 8192 bytes)
[ 5.403587] TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
[ 5.403617] TCP: Hash tables configured (established 2048 bind 2048)
[ 5.403679] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 5.403700] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 5.403817] NET: Registered protocol family 1
[ 5.405093] RPC: Registered named UNIX socket transport module.
[ 5.405103] RPC: Registered udp transport module.
[ 5.405108] RPC: Registered tcp transport module.
[ 5.405113] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 5.405290] NetWinder Floating Point Emulator V0.97 (double precision)
[ 5.405610] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initiali
zed
[ 5.405759] gpio-usb-probe-1
[ 5.405798] gpio-usb-probe-4b err=0
[ 5.405807] gpio-usb gpio-usb: USB GPIO's initialized
[ 5.406827] workingset: timestamp_bits=30 max_order=16 bucket_order=0
[ 5.407644] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 5.407979] ntfs: driver 2.1.32 [Flags: R/W].
[ 5.408006] jffs2: version 2.2. (NAND) (SUMMARY) ? 2001-2006 Red Hat, Inc.
[ 5.408108] fuse init (API version 7.26)
[ 5.408305] JFS: nTxBlock = 1953, nTxLock = 15628
[ 5.409158] SGI XFS with ACLs, security attributes, realtime, no debug enable
d
[ 5.412382] async_tx: api initialized (async)
[ 5.412442] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2
51)
[ 5.412451] io scheduler noop registered
[ 5.412456] io scheduler deadline registered
[ 5.412490] io scheduler cfq registered (default)
[ 5.412497] io scheduler mq-deadline registered
[ 5.412684] mv_xor mv_xor.0: Marvell shared XOR driver
[ 5.470544] mv_xor mv_xor.0: Marvell XOR (Registers Mode): ( xor cpy )
[ 5.471888] mv_xor mv_xor.1: Marvell shared XOR driver
[ 5.530551] mv_xor mv_xor.1: Marvell XOR (Registers Mode): ( xor cpy )
[ 5.534573] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 5.535487] console [ttyS0] disabled
[ 5.556824] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 125
00000) is a 16550A
[ 6.280228] random: fast init done
[ 6.355070] console [ttyS0] enabled
[ 6.379158] serial8250.1: ttyS1 at MMIO 0xf1012100 (irq = 34, base_baud = 125
00000) is a 16550A
[ 6.396701] brd: module loaded
[ 6.404400] loop: module loaded
[ 6.408573] ahci 0000:00:01.0: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 imp
l SATA mode
[ 6.417116] ahci 0000:00:01.0: flags: 64bit ncq pm led clo pmp pio slum part

[ 6.425420] scsi host0: ahci
[ 6.428554] ata1: SATA max UDMA/133 abar m512@0xe0010000 port 0xe0010100 irq
9
[ 6.436277] sata_mv sata_mv.0: cannot get optional clkdev
[ 6.442075] sata_mv sata_mv.0: slots 32 ports 2
[ 6.448701] scsi host1: sata_mv
[ 6.452364] scsi host2: sata_mv
[ 6.455722] ata2: SATA max UDMA/133 irq 21
[ 6.459838] ata3: SATA max UDMA/133 irq 21
[ 6.464862] nand: Could not find valid ONFI parameter page; aborting
[ 6.471841] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xdc
[ 6.478218] nand: Hynix NAND 512MiB 3,3V 8-bit
[ 6.482734] nand: 512 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB siz
e: 64
[ 6.490401] Scanning device for bad blocks
[ 6.770121] ata1: SATA link down (SStatus 0 SControl 300)
[ 6.809487] Creating 3 MTD partitions on "orion_nand":
[ 6.814683] 0x000000000000-0x000000100000 : "u-boot"
[ 6.820311] 0x000000100000-0x000001100000 : "uImage"
[ 6.826114] 0x000001100000-0x000020000000 : "root"
[ 6.834652] tun: Universal TUN/TAP device driver, 1.6
[ 6.840703] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn
.edu>
[ 6.848703] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393
@maroon.tc.umn.edu>
[ 6.863820] libphy: orion_mdio_bus: probed
[ 6.868082] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 6.970117] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 6.990141] ata2.00: ATA-10: WDC WD40EFRX-68N32N0, 82.00A82, max UDMA/133
[ 6.996956] ata2.00: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 7.030141] ata2.00: configured for UDMA/133
[ 7.050348] scsi 1:0:0:0: Direct-Access ATA WDC WD40EFRX-68N 0A82 PQ
: 0 ANSI: 5
[ 7.058847] fvdw1 disk index before get_sd_name = 0
[ 7.063854] device-name= sata_mv
[ 7.067098] fvdw2 disk index after get_sd_name = 0
[ 7.071933] fvdw3 prefix[0]=s prefix[1]=d
[ 7.076057] fvdw4 diskname = sda
[ 7.079701] sd 1:0:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.
64 TiB)
[ 7.088340] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address
00:d0:4b:93:20:0d
[ 7.097337] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 7.102738] PPP generic driver version 2.4.2
[ 7.107231] sd 1:0:0:0: [sda] Write Protect is off
[ 7.112260] PPP Deflate Compression module registered
[ 7.117342] PPP MPPE Compression module registered
[ 7.122333] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, does
n't support DPO or FUA
[ 7.131452] NET: Registered protocol family 24
[ 7.135932] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet dri
ver
[ 7.144297] usbcore: registered new interface driver pegasus
[ 7.150171] usbcore: registered new interface driver asix
[ 7.155661] usbcore: registered new interface driver ax88179_178a
[ 7.161916] usbcore: registered new interface driver cdc_ether
[ 7.167899] usbcore: registered new interface driver net1080
[ 7.173697] usbcore: registered new interface driver plusb
[ 7.179338] usbcore: registered new interface driver cdc_subset
[ 7.185399] usbcore: registered new interface driver zaurus
[ 7.191144] usbcore: registered new interface driver ipheth
[ 7.196874] usbcore: registered new interface driver cdc_ncm
[ 7.203034] aoe: cannot create debugfs directory
[ 7.207989] aoe: AoE v85 initialised.
[ 7.212019] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 7.218180] i2c /dev entries driver
[ 7.227497] rtc-ds1307 0-0068: registered as rtc1
[ 7.232617] uvcvideo: Unable to create debugfs directory
[ 7.238197] usbcore: registered new interface driver uvcvideo
[ 7.244037] USB Video Class driver (1.1.1)
[ 7.248151] gspca_main: v2.14.0 registered
[ 7.252398] usbcore: registered new interface driver Philips webcam
[ 7.267351] gpio-fan gpio-fan: GPIO fan initialized
[ 7.272977] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-d
evel@redhat.com
[ 7.281895] device-mapper: multipath round-robin: version 1.2.0 loaded
[ 7.288446] device-mapper: multipath queue-length: version 0.2.0 loaded
[ 7.295155] device-mapper: multipath service-time: version 0.3.0 loaded
[ 7.301894] device-mapper: dm-log-userspace: version 1.3.0 loaded
[ 7.308014] device-mapper: raid: Loading target version 1.13.0
[ 7.315190] Netfilter messages via NETLINK v0.30.
[ 7.319927] nfnl_acct: registering with nfnetlink.
[ 7.325460] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)
[ 7.331866] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 7.337899] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.343650] NET: Registered protocol family 10
[ 7.348825] Segment Routing with IPv6
[ 7.352705] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.358318] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 7.364855] NET: Registered protocol family 17
[ 7.369351] Bridge firewalling registered
[ 7.373692] NET: Registered protocol family 5
[ 7.378778] netpoll: netconsole: local port 6666
[ 7.383580] netpoll: netconsole: local IPv4 address 10.0.0.252
[ 7.389440] netpoll: netconsole: interface 'eth0'
[ 7.394194] netpoll: netconsole: remote port 6666
[ 7.398919] netpoll: netconsole: remote IPv4 address 10.0.0.77
[ 7.404841] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[ 7.411775] netpoll: netconsole: device eth0 not up yet, forcing it
[ 7.420127] ata3: SATA link down (SStatus 0 SControl F300)
[ 7.611281] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 7.688735] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[ 7.695767] sd 1:0:0:0: [sda] Attached SCSI disk
[ 10.081146] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, ful
l duplex, flow control enabled
[ 10.090973] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 10.102843] console [netcon0] enabled
[ 10.106534] netconsole: network logging started
[ 10.111422] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 10.118513] rtc-mv rtc-mv: setting system clock to 2000-01-01 00:00:00 UTC (9
46684800)
[ 10.126914] md: Skipping autodetection of RAID arrays. (raid=autodetect will
force)
[ 10.147018] EXT4-fs (sda7): mounting ext3 file system using the ext4 subsyste
m
[ 10.170368] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts:
(null)
[ 10.178116] VFS: Mounted root (ext3 filesystem) on device 8:7.
[ 10.184620] Freeing unused kernel memory: 192K
[ 10.189100] This architecture does not have kernel memory protection.
[ 10.502450] EXT4-fs (sda7): re-mounted. Opts: (null)
[ 11.239424] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 11.246528] ehci-orion: EHCI orion driver
[ 11.250731] orion-ehci orion-ehci.0: EHCI Host Controller
[ 11.256188] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num
ber 1
[ 11.263957] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 11.290102] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 11.296171] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 11.303022] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=
1
[ 11.310306] usb usb1: Product: EHCI Host Controller
[ 11.315217] usb usb1: Manufacturer: Linux 4.14.133 ehci_hcd
[ 11.320837] usb usb1: SerialNumber: orion-ehci.0
[ 11.325741] hub 1-0:1.0: USB hub found
[ 11.329544] hub 1-0:1.0: 1 port detected
[ 11.346140] usbcore: registered new interface driver usb-storage
[ 11.362591] usbcore: registered new interface driver usblp
[ 11.391963] Loading iSCSI transport class v2.0-870.
[ 11.400449] iscsi: registered transport (tcp)
[ 11.626192] EXT4-fs (sda5): mounting ext3 file system using the ext4 subsyste
m
[ 11.638421] EXT4-fs (sda5): warning: checktime reached, running e2fsck is rec
ommended
[ 11.650290] EXT4-fs (sda5): mounted filesystem with ordered data mode. Opts:
(null)
[ 11.733316] random: mkswap: uninitialized urandom read (16 bytes read)
[ 11.768087] Adding 524284k swap on /dev/sda3. Priority:-2 extents:1 across:5
24284k
[ 24.186886] udevd (1033): /proc/1033/oom_adj is deprecated, please use /proc/
1033/oom_score_adj instead.
[ 24.196590] udev: starting version 130
[ 24.566196] synth uevent: /gpiochip0: failed to send uevent
[ 24.566212] gpio gpiochip0: uevent: failed to send synthetic uevent
[ 24.649626] synth uevent: /gpiochip1: failed to send uevent
[ 24.649641] gpio gpiochip1: uevent: failed to send synthetic uevent
[ 25.090157] random: crng init done
[ 32.829950] EXT4-fs (sda8): warning: checktime reached, running e2fsck is rec
ommended
[ 33.583239] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts:
user_xattr,acl,nodelalloc
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby fvdw » Fri Nov 18, 2022 2:28 pm

seems to me that firmware must be running, what does the blue led tells you?
fvdw
Site Admin - expert
 
Posts: 13471
Joined: Tue Apr 12, 2011 2:30 pm
Location: Netherlands

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:29 pm

fvdw wrote:seems to me that firmware must be running, what does the blue led tells you?

steady blue
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:30 pm

At last !!! I can see him
Can you remember me please user name and pass ??
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

Re: Blue LED Blinking and no network access to 2Big Network

Postby fvdw » Fri Nov 18, 2022 2:31 pm

usr: admin-nas
pasw: admin
fvdw
Site Admin - expert
 
Posts: 13471
Joined: Tue Apr 12, 2011 2:30 pm
Location: Netherlands

Re: Blue LED Blinking and no network access to 2Big Network

Postby PaaNooS » Fri Nov 18, 2022 2:36 pm

And can you remember me please how install 18.2 ?
PaaNooS
Donator VIP
Donator VIP
 
Posts: 120
Joined: Tue Nov 15, 2022 10:16 am

PreviousNext

Return to Lacie 2Big Network vs2

Who is online

Users browsing this forum: Google [Bot] and 9 guests