- Code: Select all
disk 0x400000 0:6
it should load the kernel, it also should output info on the kernel itself
disk 0x400000 0:6
bootm
Marvell>> ide reset
ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 4: OK
Model: ST31500341AS Firm: CC4H Ser#:
9VS1YBWD
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)
Marvell>>
Marvell>> disk 0x400000 0:6
disk 0x400000 0:6
** Device 0 not available
Marvell>>
provided by fvdw
waiting for u-boot..
starting u-boot net console click on window and press enter
Marvell>> ide reset
ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 4: OK
Model: ST31500341AS Firm: CC4H Ser#:
9VS1YBWD
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)
Marvell>> disk 0x400000 4:6
disk 0x400000 4:6
Loading from IDE device 4, partition 6: Name: hde6
Type: U-Boot
Image Name: Linux-3.9.5
Created: 2014-02-27 21:23:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1851688 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Marvell>>
Marvell>> bootm
bootm
## Booting image at 00400000 ...
Image Name: Linux-3.9.5
Created: 2014-02-27 21:23:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1851688 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
setenv bootargs console=ttyS0,115200 netconsole=6666@${ipaddr}/,6666@${serverip}/ root=/dev/sda7
printenv bootargs
ide reset
disk 0x400000 4:6
bootm
Marvell>>printenv bootargs
bootargs=console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.42/
root=/dev/sda7
Marvell>> ide reset
ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 4: OK
Model: ST31500341AS Firm: CC4H Ser#:
9VS1YBWD
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1430799.3 MB = 1397.2 GB (-1364690128 x 512)
Marvell>> disk 0x400000 4:6
disk 0x400000 4:6
Loading from IDE device 4, partition 6: Name: hde6
Type: U-Boot
Image Name: Linux-3.9.5
Created: 2014-02-27 21:23:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1851688 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Marvell>> bootm
bootm
## Booting image at 00400000 ...
Image Name: Linux-3.9.5
Created: 2014-02-27 21:23:00 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1851688 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Booting Linux on physical CPU 0x0
Linux version 3.9.5 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #25 Thu
Feb 27 22:22:32 GMT+1 2014
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@19
2.168.1.42/ root=/dev/sda7
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
__ex_table already sorted, skipping sort
Memory: 128MB = 128MB total
Memory: 126024k/126024k available, 5048k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
vmalloc : 0xc8800000 - 0xff000000 ( 872 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.text : 0xc0008000 - 0xc0355fdc (3384 kB)
.init : 0xc0356000 - 0xc0374ebc ( 124 kB)
.data : 0xc0376000 - 0xc039bee0 ( 152 kB)
.bss : 0xc039bee0 - 0xc03ca8dc ( 187 kB)
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Console: colour dummy device 80x30
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
Setting up static identity map for 0xc028ffc8 - 0xc0290004
NET: Registered protocol family 16
DMA: preallocated 1024 KiB pool for atomic coherent allocations
Register Driver 'dummy'
5big1 init started
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
5big1 init 1
5big1 init 2
net5big: powering up SATA drives
5big1 init 3
5big1 init 4
5big1 init 5
5big1 init 6
5big1 init 7
5big1 init 8
5big1 init 9
5big1 init 10
5big1 init 11
5big1 init 12
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
5big1 init end
net5big_pci_preinit failed to gpio_request 20
PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
pci_bus 0000:00: root bus resource [io 0x1000-0xffff]
pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
PCI: bus0: Fast back to back transfers disabled
PCI host bridge to bus 0000:01
pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff]
pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 2: assigned [io 0x10000-0x100ff]
bio: create slab <bio-0> at 0
vgaarb: loaded
SCSI subsystem initialized
Register Driver 'Generic PHY'
Register Driver 'usbfs'
usbcore: registered new interface driver usbfs
Register Driver 'hub'
usbcore: registered new interface driver hub
Register Driver 'usb'
usbcore: registered new device driver usb
Register Driver 'i2c-gpio'
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP: reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
Register Driver 'alarmtimer'
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Register Driver 'mv_xor'
mv_xor mv_xor.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
Register Driver 'serial8250'
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
Register Driver 'serial'
brd: module loaded
loop: module loaded
Register Driver 'at24'
Register Driver 'eeprom'
Register Driver 'sd'
Register Driver 'ahci'
Register Driver 'sata_mv'
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
Register Driver 'sata_mv'
sata_mv sata_mv.0: cannot get optional clkdev
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.
edu>
Register Driver 'mv643xx_eth'
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
libphy: mv643xx_eth smi: probed
Register Driver 'mv643xx_eth_port'
mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:88:5b
:ff
mousedev: PS/2 mouse device common for all mice
Register Driver 'rtc-ds1307'
Register Driver 'rtc-ds1374'
Register Driver 'rtc-rs5c372'
i2c /dev entries driver
Register Driver 'mv64xxx_i2c'
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
Register Driver 'g762'
g762 probe started
g762 probe 1
g762 probe 2
g762 probe 3
g762 probe 4
g762 probe 5
g762 probe 6
g762 probe 7
Register Driver 'gpio-fan'
Register Driver 'lm75'
Register Driver 'lm77'
Register Driver 'leds-gpio'
Register Driver 'mv_crypto'
Netfilter messages via NETLINK v0.30.
IPv4 over IPv4 tunneling driver
TCP: cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
netpoll: netconsole: local port 6666
netpoll: netconsole: local IPv4 address 192.168.1.252
netpoll: netconsole: interface 'eth0'
netpoll: netconsole: remote port 6666
netpoll: netconsole: remote IPv4 address 192.168.1.42
netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
netpoll: netconsole: device eth0 not up yet, forcing it
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 300)
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: ST31500341AS, CC4H, max UDMA/133
ata5.00: 2930277168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA ST31500341AS CC4H PQ: 0 ANSI: 5
fvdw1 disk index before get_sd_name = 0
device-name= sata_mv
fvdw2 disk index after get_sd_name = 0
fvdw3 prefix[0]=s prefix[1]=d
fvdw4 diskname = sda
sd 4:0:0:0: [sda] 2930277168 512-byte logical blocks: (1.50 TB/1.36 TiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO
or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: [sda] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow
control disabled
console [netcon0] enabled
netconsole: network logging started
rtc-rs5c372 0-0032: setting system clock to 2015-10-04 19:54:40 UTC (1443988480)
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): warning: checktime reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) on device 8:7.
Freeing init memory: 120K
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
See Linux Documentation/init.txt for guidance.
Backtrace:
[<c0010d7c>] (dump_backtrace+0x0/0x108) from [<c028c28c>] (dump_stack+0x18/0x1c)
r6:c039c5c8 r5:c028addc r4:c039bee0 r3:00000001
[<c028c274>] (dump_stack+0x0/0x1c) from [<c028c3e8>] (panic+0x84/0x1d0)
[<c028c364>] (panic+0x0/0x1d0) from [<c028ae9c>] (kernel_init+0xc0/0xec)
r3:c7820d60 r2:00000003 r1:0000706e r0:c030c62a
r7:00000000
[<c028addc>] (kernel_init+0x0/0xec) from [<c000d9d0>] (ret_from_fork+0x14/0x24)
r4:00000000 r3:00000000
ls -al /sda7/sbin
(none) login: root
Password:
root@(none):/ # mkdir /sda7
root@(none):/ # mount /dev/sda7 /sda7
root@(none):/ # cd /sda7
root@(none):/sda7 # cd sbin
root@(none):/sda7/sbin # ls -al
total 0
root@(none):/sda7/sbin #
Return to Lacie 5Big Network vs1
Users browsing this forum: boerie and 7 guests