Need some help to enable WIFI with D-LINK DWA-125

[lkriry]

Hi,

Thanks for your great firmware. By the way, I can't activate my wifi dongle on my Network Space 2 Classic.

I used the last firmware: fvdw-sl firmware version 15-3
My dongle: D-LINK DWA-125 Ver:A1 F/W Ver: 1.10

No light appears on the dongle. I think I have a problem with the driver !

T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 1
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev=03.13
S: Manufacturer=Linux 3.13.6 ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=orion-ehci.0
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=07d1 ProdID=3c0d Rev=01.01
S: Manufacturer=Ralink
S: Product=11n Adapter
S: SerialNumber=1.0
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I: If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2800usb

-------------------------------------------------------------------------------------------------

root@fvdwsl-base:/lib/firmware/rtlwifi # iwconfig
ipddp0 no wireless extensions.

lo no wireless extensions.

tunl0 no wireless extensions.

sit0 no wireless extensions.

wlan0 IEEE 802.11bgn ESSID:off/any
Mode:Managed Access Point: Not-Associated Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:on

eth0 no wireless extensions.

-------------------------------------------------------------------------------------------------

root@fvdwsl-base:/lib/firmware/rtlwifi # ifconfig
eth0 Link encap:Ethernet HWaddr 00:D0:4B:8D:AD:EC
inet addr:192.168.1.252 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::2d0:4bff:fe8d:adec/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:2346 errors:0 dropped:0 overruns:0 frame:0
TX packets:2225 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:365700 (357.1 KiB) TX bytes:1442401 (1.3 MiB)
Interrupt:11

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:81 errors:0 dropped:0 overruns:0 frame:0
TX packets:81 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1954 (1.9 KiB) TX bytes:1954 (1.9 KiB)

-------------------------------------------------------------------------------------------------
dmesg =>
[ 4634.248117] usb 1-1: new high-speed USB device number 6 using orion-ehci
[ 4634.415307] usb 1-1: New USB device found, idVendor=07d1, idProduct=3c0d
[ 4634.422022] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 4634.429142] usb 1-1: Product: 11n Adapter
[ 4634.433138] usb 1-1: Manufacturer: Ralink
[ 4634.437138] usb 1-1: SerialNumber: 1.0
[ 4634.568116] usb 1-1: reset high-speed USB device number 6 using orion-ehci
[ 4634.729055] ieee80211 phy4: rt2x00_set_rt: Info - RT chipset 3070, rev 0201 detected
[ 4634.764927] ieee80211 phy4: rt2x00_set_rf: Info - RF chipset 0005 detected
[ 4634.773845] ieee80211 phy4: Selected rate control algorithm 'minstrel_ht'
root@fvdwsl-base:/lib/firmware/rtlwifi #


I also did all the steps speficied in this document: viewtopic.php?f=7&t=1829 but no success.

Could you please help me to get wifi on my Lacie ?

Thanks

[lkriry]

just set the wlan0 up using:

ifconfig wlan0 up

It's working !

[fvdw]

;) glad to read you managed to solve it yourself :thumbup