Hi! Some general question + Wifi USB Realtek RTL8191S

[fvdw]

thx

it doesn't seem to load firmware, but maybe this is not needed for this dongle

remarkable that it mentions it has an rt2x00 chip set and it loads a rt2800 dirver and not the rt2x00.

Code: Select all

[ 1073.798825] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1073.991961] usb 1-1: New USB device found, idVendor=148f, idProduct=5370
[ 1073.998654] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1074.025726] usb 1-1: Product: 802.11 n WLAN
[ 1074.030069] usb 1-1: Manufacturer: Ralink
[ 1074.034420] usb 1-1: SerialNumber: 1.0
[ 1074.989196] FAT-fs (loop0): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 1075.019368] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[13247.935123] Register Driver 'rt2800usb'
[13248.049289] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[13248.225262] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 5390, rf: 5370, rev: 0502.
[13248.246465] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[13248.279872] usbcore: registered new interface driver rt2800usb

Maybe you can do on thursday a a reboot without the dongle inserted, then load the modules and then insert the dongle to see the clean output of dmesg

[matzi]

Finally back home I can go on with it:

lsmod after reboot before loading the drivers:

root@fvdwsl-base:/ # lsmod
iscsi_tcp 7739 0 - Live 0xbf06e000
libiscsi_tcp 11307 1 iscsi_tcp, Live 0xbf067000
libiscsi 30681 2 iscsi_tcp,libiscsi_tcp, Live 0xbf059000
scsi_transport_iscsi 34596 2 iscsi_tcp,libiscsi, Live 0xbf048000
iscsi_trgt 100262 0 - Live 0xbf026000 (O)
usblp 9895 0 - Live 0xbf01f000
usb_storage 36450 0 - Live 0xbf00e000
ehci_hcd 33779 0 - Live 0xbf000000

modprobing drivers:

root@fvdwsl-base:/ # modprobe rt2800lib
root@fvdwsl-base:/ # modprobe rt2800usb

rt2800usb 15733 0 - Live 0xbf09b000
rt2x00usb 7799 1 rt2800usb, Live 0xbf095000
rt2800lib 50370 1 rt2800usb, Live 0xbf083000
rt2x00lib 32920 3 rt2800usb,rt2x00usb,rt2800lib, Live 0xbf074000
iscsi_tcp 7739 0 - Live 0xbf06e000
libiscsi_tcp 11307 1 iscsi_tcp, Live 0xbf067000
libiscsi 30681 2 iscsi_tcp,libiscsi_tcp, Live 0xbf059000
scsi_transport_iscsi 34596 2 iscsi_tcp,libiscsi, Live 0xbf048000
iscsi_trgt 100262 0 - Live 0xbf026000 (O)
usblp 9895 0 - Live 0xbf01f000
usb_storage 36450 0 - Live 0xbf00e000
ehci_hcd 33779 0 - Live 0xbf000000

See that I did not modprobe rt2x00 driver!

dmesg before inserting dongle

[ 8.215952] Register Driver 'usb'
[ 8.216113] usbcore: registered new device driver usb
[ 8.216471] Register Driver 'i2c-gpio'
[ 8.216668] Linux video capture interface: v2.00
[ 8.219330] cfg80211: Calling CRDA to update world regulatory domain
[ 8.220605] Switching to clocksource orion_clocksource
[ 8.223512] NET: Registered protocol family 2
[ 8.224191] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 8.224244] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 8.224274] TCP: Hash tables configured (established 1024 bind 1024)
[ 8.224361] TCP: reno registered
[ 8.224380] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 8.224411] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 8.224641] NET: Registered protocol family 1
[ 8.225013] RPC: Registered named UNIX socket transport module.
[ 8.225029] RPC: Registered udp transport module.
[ 8.225039] RPC: Registered tcp transport module.
[ 8.225050] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.225066] PCI: CLS 0 bytes, default 32
[ 8.225379] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.225398] Register Driver 'gpio-usb'
[ 8.225563] gpio-usb: probe of gpio-usb failed with error -22
[ 8.225798] Register Driver 'gpio-ws-leds'
[ 8.226495] Register Driver 'alarmtimer'
[ 8.356766] VFS: Disk quotas dquot_6.5.2
[ 8.356838] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.357346] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.357707] NTFS driver 2.1.30 [Flags: R/W].
[ 8.357764] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 8.357985] fuse init (API version 7.21)
[ 8.358763] JFS: nTxBlock = 950, nTxLock = 7606
[ 8.359391] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 8.359852] msgmni has been set to 237
[ 8.361310] async_tx: api initialized (async)
[ 8.361572] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.361590] io scheduler noop registered
[ 8.361602] io scheduler deadline registered
[ 8.361627] io scheduler cfq registered (default)
[ 8.361653] Register Driver 'kirkwood-pinctrl'
[ 8.361900] Register Driver 'mv_xor'
[ 8.361967] mv_xor mv_xor.0: Marvell shared XOR driver
[ 8.400725] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.440712] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[ 8.441023] mv_xor mv_xor.1: Marvell shared XOR driver
[ 8.480712] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 8.520712] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 8.527672] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.528495] Register Driver 'serial8250'
[ 8.548858] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 9.115255] console [ttyS0] enabled
[ 9.129489] brd: module loaded
[ 9.137850] loop: module loaded
[ 9.141338] Register Driver 'at24'
[ 9.144997] Register Driver 'eeprom'
[ 9.149630] Register Driver 'sd'
[ 9.153331] Register Driver 'ahci'
[ 9.157050] Register Driver 'sata_mv'
[ 9.161119] Register Driver 'sata_mv'
[ 9.164920] sata_mv sata_mv.0: version 1.28
[ 9.165024] sata_mv sata_mv.0: cannot get optional clkdev
[ 9.170504] sata_mv sata_mv.0: slots 32 ports 2
[ 9.179045] scsi0 : sata_mv
[ 9.182495] scsi1 : sata_mv
[ 9.185745] ata1: SATA max UDMA/133 irq 21
[ 9.189829] ata2: SATA max UDMA/133 irq 21
[ 9.195345] Register Driver 'physmap-flash'
[ 9.199786] Generic platform RAM MTD, (c) 2004 Simtec Electronics
[ 9.206174] Register Driver 'mtd-ram'
[ 9.210101] Register Driver 'm25p80'
[ 9.214064] Register Driver 'gen_nand'
[ 9.218109] Register Driver 'orion_nand'
[ 9.222496] platform_driver_probe 5 retval= -19 code= 0
[ 9.227790] Register Driver 'orion_spi'
[ 9.232414] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[ 9.237430] Creating 2 MTD partitions on "spi_flash":
[ 9.242559] 0x000000000000-0x00000007d000 : "u-boot"
[ 9.248820] 0x00000007e000-0x00000007f000 : "u-boot-env"
[ 9.255700] tun: Universal TUN/TAP device driver, 1.6
[ 9.260865] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 9.267228] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 9.275736] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 9.284581] Register Driver 'mv643xx_eth'
[ 9.288715] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 9.295732] libphy: mv643xx_eth smi: probed
[ 9.300135] Register Driver 'mv643xx_eth_port'
[ 9.307104] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:91:71:ff
[ 9.316054] PPP generic driver version 2.4.2
[ 9.320778] PPP Deflate Compression module registered
[ 9.325824] PPP MPPE Compression module registered
[ 9.330598] NET: Registered protocol family 24
[ 9.335133] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 9.342671] Register Driver 'pegasus'
[ 9.346604] usbcore: registered new interface driver pegasus
[ 9.352321] Register Driver 'ipheth'
[ 9.356144] usbcore: registered new interface driver ipheth
[ 9.363104] aoe: AoE v81 initialised.
[ 9.366823] Register Driver 'rtc-ds1307'
[ 9.371035] Register Driver 'rtc-mv'
[ 9.375152] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 9.381186] platform_driver_probe 5 retval= 0 code= 0
[ 9.386308] i2c /dev entries driver
[ 9.389973] Register Driver 'mv64xxx_i2c'
[ 9.395144] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[ 9.402751] uvcvideo: Unable to create debugfs directory
[ 9.408048] Register Driver 'uvcvideo'
[ 9.412170] usbcore: registered new interface driver uvcvideo
[ 9.417895] USB Video Class driver (1.1.1)
[ 9.422065] gspca_main: v2.14.0 registered
[ 9.426148] Register Driver 'Philips webcam'
[ 9.430710] usbcore: registered new interface driver Philips webcam
[ 9.436956] Register Driver 'gpio-fan'
[ 9.441024] Register Driver 'lm75'
[ 9.445526] Register Driver 'lm77'
[ 9.449579] md: linear personality registered for level -1
[ 9.455090] md: raid0 personality registered for level 0
[ 9.460379] md: raid1 personality registered for level 1
[ 9.465716] md: raid10 personality registered for level 10
[ 9.471262] md: raid6 personality registered for level 6
[ 9.476553] md: raid5 personality registered for level 5
[ 9.481885] md: raid4 personality registered for level 4
[ 9.487402] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 9.496041] device-mapper: multipath: version 1.5.1 loaded
[ 9.501571] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 9.508073] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 9.514694] device-mapper: multipath service-time: version 0.2.0 loaded
[ 9.521407] device-mapper: dm-log-userspace: version 1.1.0 loaded
[ 9.527478] device-mapper: raid: Loading target version 1.4.2
[ 9.533240] Register Driver 'mmcblk'
[ 9.537051] Register Driver 'leds-gpio'
[ 9.541157] leds-gpio leds-gpio: pins are not configured from the driver
[ 9.547839] orion_gpio_is_valid: invalid GPIO 12
[ 9.548231] Register Driver 'leds-ns2'
[ 9.552285] Register Driver 'leds-ns2l'
[ 9.556634] Register Driver 'leds-netxbig'
[ 9.561055] Register Driver 'mv_crypto'
[ 9.565969] Register Driver 'hid-generic'
[ 9.570248] Register Driver 'r8712u'
[ 9.574237] usbcore: registered new interface driver r8712u
[ 9.579853] Netfilter messages via NETLINK v0.30.
[ 9.584747] nf_conntrack version 0.5.0 (1901 buckets, 7604 max)
[ 9.591158] IPv4 over IPv4 tunneling driver
[ 9.596419] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.601910] TCP: cubic registered
[ 9.605258] NET: Registered protocol family 10
[ 9.610841] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.616323] sit: IPv6 over IPv4 tunneling driver
[ 9.622004] NET: Registered protocol family 17
[ 9.626455] NET: Registered protocol family 5
[ 9.631039] NET: Registered protocol family 37
[ 9.635706] VFP support v0.3: not present
[ 9.641068] console [netcon0] enabled
[ 9.644712] netconsole: network logging started
[ 9.649223] Register Driver 'gpio-keys'
[ 9.653748] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 9.660961] rtc-mv rtc-mv: setting system clock to 2013-10-17 19:00:15 UTC (1382036415)
[ 9.700687] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.740713] ata1.00: ATA-8: WDC WD25EZRX-00AZ6B0, 80.00A80, max UDMA/133
[ 9.747397] ata1.00: 4883781168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.790714] ata1.00: configured for UDMA/133
[ 9.811060] scsi 0:0:0:0: Direct-Access ATA WDC WD25EZRX-00A 80.0 PQ: 0 ANSI: 5
[ 9.819696] No LaCie disk map available
[ 9.824177] sd 0:0:0:0: [sda] 4883781168 512-byte logical blocks: (2.50 TB/2.27 TiB)
[ 9.832544] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 9.838057] sd 0:0:0:0: [sda] Write Protect is off
[ 9.842906] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 9.843053] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.887659] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[ 9.896443] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.180675] ata2: SATA link down (SStatus 0 SControl F300)
[ 10.200725] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[ 10.244759] EXT3-fs (sda7): mounted filesystem with ordered data mode
[ 10.251225] kjournald starting. Commit interval 5 seconds
[ 10.256725] VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
[ 10.264144] Freeing init memory: 184K
[ 10.465108] EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended
[ 10.474199] EXT3-fs (sda7): using internal journal
[ 11.010879] EXT3-fs (sda1): warning: checktime reached, running e2fsck is recommended
[ 11.018769] kjournald starting. Commit interval 5 seconds
[ 11.024337] EXT3-fs (sda1): using internal journal
[ 11.040731] EXT3-fs (sda1): recovery complete
[ 11.045078] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 12.220946] kjournald starting. Commit interval 5 seconds
[ 12.226478] EXT3-fs (sda5): using internal journal
[ 12.250740] EXT3-fs (sda5): recovery complete
[ 12.255084] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 12.479881] Adding 516092k swap on /dev/sda3. Priority:-1 extents:1 across:516092k
[ 12.782257] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.788769] Register Driver 'orion-ehci'
[ 12.792980] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 12.798215] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 12.806026] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 12.830669] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 12.836658] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.843446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.850658] usb usb1: Product: Marvell Orion EHCI
[ 12.855351] usb usb1: Manufacturer: Linux 3.9.5 ehci_hcd
[ 12.860662] usb usb1: SerialNumber: orion-ehci.0
[ 12.866013] hub 1-0:1.0: USB hub found
[ 12.869771] hub 1-0:1.0: 1 port detected
[ 12.887220] Initializing USB Mass Storage driver...
[ 12.892227] Register Driver 'usb-storage'
[ 12.896591] usbcore: registered new interface driver usb-storage
[ 12.902715] USB Mass Storage support registered.
[ 12.917332] Register Driver 'usblp'
[ 12.921261] usbcore: registered new interface driver usblp
[ 12.940406] iSCSI Enterprise Target Software - version trunk
[ 12.946347] iscsi_trgt: Registered io type fileio
[ 12.951091] iscsi_trgt: Registered io type blockio
[ 12.955864] iscsi_trgt: Registered io type nullio
[ 12.972905] Loading iSCSI transport class v2.0-870.
[ 12.985669] iscsi: registered transport (tcp)
[ 26.180699] kjournald starting. Commit interval 5 seconds
[ 26.188633] EXT3-fs (sda8): using internal journal
[ 26.230772] EXT3-fs (sda8): recovery complete
[ 26.235124] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 26.481067] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.746452] udevd (833): /proc/833/oom_adj is deprecated, please use /proc/833/oom_score_adj instead.
[ 28.294338] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[ 28.304117] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.184984] FAT-fs (loop0): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 41.211465] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1175.004612] Register Driver 'rt2800usb'
[ 1175.025597] usbcore: registered new interface driver rt2800usb

dmesg after inserting dongle

[ 7.500635] mv_usb_init 2 devnum = 0
[ 7.500659] init function mv_usb_init finished
[ 7.500671] initial MPP regs: 01112222 00003311 00501100 00000000 00000000 00000000 00000000
[ 7.500715] final MPP regs: 01112222 00003311 00551100 00000000 00000000 00000000 00000000
[ 7.500952] orion-ehci registered
[ 7.537742] bio: create slab <bio-0> at 0
[ 7.703713] raid6: int32x1 72 MB/s
[ 7.872977] raid6: int32x2 98 MB/s
[ 8.043444] raid6: int32x4 90 MB/s
[ 8.212954] raid6: int32x8 104 MB/s
[ 8.212968] raid6: using algorithm int32x8 (104 MB/s)
[ 8.212978] raid6: using intx1 recovery algorithm
[ 8.214091] SCSI subsystem initialized
[ 8.214673] libata version 3.00 loaded.
[ 8.215020] Register Driver 'Generic PHY'
[ 8.215395] Register Driver 'usbfs'
[ 8.215620] usbcore: registered new interface driver usbfs
[ 8.215642] Register Driver 'hub'
[ 8.215856] usbcore: registered new interface driver hub
[ 8.215952] Register Driver 'usb'
[ 8.216113] usbcore: registered new device driver usb
[ 8.216471] Register Driver 'i2c-gpio'
[ 8.216668] Linux video capture interface: v2.00
[ 8.219330] cfg80211: Calling CRDA to update world regulatory domain
[ 8.220605] Switching to clocksource orion_clocksource
[ 8.223512] NET: Registered protocol family 2
[ 8.224191] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
[ 8.224244] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 8.224274] TCP: Hash tables configured (established 1024 bind 1024)
[ 8.224361] TCP: reno registered
[ 8.224380] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 8.224411] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 8.224641] NET: Registered protocol family 1
[ 8.225013] RPC: Registered named UNIX socket transport module.
[ 8.225029] RPC: Registered udp transport module.
[ 8.225039] RPC: Registered tcp transport module.
[ 8.225050] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 8.225066] PCI: CLS 0 bytes, default 32
[ 8.225379] NetWinder Floating Point Emulator V0.97 (double precision)
[ 8.225398] Register Driver 'gpio-usb'
[ 8.225563] gpio-usb: probe of gpio-usb failed with error -22
[ 8.225798] Register Driver 'gpio-ws-leds'
[ 8.226495] Register Driver 'alarmtimer'
[ 8.356766] VFS: Disk quotas dquot_6.5.2
[ 8.356838] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 8.357346] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 8.357707] NTFS driver 2.1.30 [Flags: R/W].
[ 8.357764] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 8.357985] fuse init (API version 7.21)
[ 8.358763] JFS: nTxBlock = 950, nTxLock = 7606
[ 8.359391] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 8.359852] msgmni has been set to 237
[ 8.361310] async_tx: api initialized (async)
[ 8.361572] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 8.361590] io scheduler noop registered
[ 8.361602] io scheduler deadline registered
[ 8.361627] io scheduler cfq registered (default)
[ 8.361653] Register Driver 'kirkwood-pinctrl'
[ 8.361900] Register Driver 'mv_xor'
[ 8.361967] mv_xor mv_xor.0: Marvell shared XOR driver
[ 8.400725] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 8.440712] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
[ 8.441023] mv_xor mv_xor.1: Marvell shared XOR driver
[ 8.480712] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[ 8.520712] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 8.527672] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.528495] Register Driver 'serial8250'
[ 8.548858] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 9.115255] console [ttyS0] enabled
[ 9.129489] brd: module loaded
[ 9.137850] loop: module loaded
[ 9.141338] Register Driver 'at24'
[ 9.144997] Register Driver 'eeprom'
[ 9.149630] Register Driver 'sd'
[ 9.153331] Register Driver 'ahci'
[ 9.157050] Register Driver 'sata_mv'
[ 9.161119] Register Driver 'sata_mv'
[ 9.164920] sata_mv sata_mv.0: version 1.28
[ 9.165024] sata_mv sata_mv.0: cannot get optional clkdev
[ 9.170504] sata_mv sata_mv.0: slots 32 ports 2
[ 9.179045] scsi0 : sata_mv
[ 9.182495] scsi1 : sata_mv
[ 9.185745] ata1: SATA max UDMA/133 irq 21
[ 9.189829] ata2: SATA max UDMA/133 irq 21
[ 9.195345] Register Driver 'physmap-flash'
[ 9.199786] Generic platform RAM MTD, (c) 2004 Simtec Electronics
[ 9.206174] Register Driver 'mtd-ram'
[ 9.210101] Register Driver 'm25p80'
[ 9.214064] Register Driver 'gen_nand'
[ 9.218109] Register Driver 'orion_nand'
[ 9.222496] platform_driver_probe 5 retval= -19 code= 0
[ 9.227790] Register Driver 'orion_spi'
[ 9.232414] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[ 9.237430] Creating 2 MTD partitions on "spi_flash":
[ 9.242559] 0x000000000000-0x00000007d000 : "u-boot"
[ 9.248820] 0x00000007e000-0x00000007f000 : "u-boot-env"
[ 9.255700] tun: Universal TUN/TAP device driver, 1.6
[ 9.260865] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 9.267228] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 9.275736] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 9.284581] Register Driver 'mv643xx_eth'
[ 9.288715] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 9.295732] libphy: mv643xx_eth smi: probed
[ 9.300135] Register Driver 'mv643xx_eth_port'
[ 9.307104] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:91:71:ff
[ 9.316054] PPP generic driver version 2.4.2
[ 9.320778] PPP Deflate Compression module registered
[ 9.325824] PPP MPPE Compression module registered
[ 9.330598] NET: Registered protocol family 24
[ 9.335133] pegasus: v0.6.14 (2006/09/27), Pegasus/Pegasus II USB Ethernet driver
[ 9.342671] Register Driver 'pegasus'
[ 9.346604] usbcore: registered new interface driver pegasus
[ 9.352321] Register Driver 'ipheth'
[ 9.356144] usbcore: registered new interface driver ipheth
[ 9.363104] aoe: AoE v81 initialised.
[ 9.366823] Register Driver 'rtc-ds1307'
[ 9.371035] Register Driver 'rtc-mv'
[ 9.375152] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 9.381186] platform_driver_probe 5 retval= 0 code= 0
[ 9.386308] i2c /dev entries driver
[ 9.389973] Register Driver 'mv64xxx_i2c'
[ 9.395144] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[ 9.402751] uvcvideo: Unable to create debugfs directory
[ 9.408048] Register Driver 'uvcvideo'
[ 9.412170] usbcore: registered new interface driver uvcvideo
[ 9.417895] USB Video Class driver (1.1.1)
[ 9.422065] gspca_main: v2.14.0 registered
[ 9.426148] Register Driver 'Philips webcam'
[ 9.430710] usbcore: registered new interface driver Philips webcam
[ 9.436956] Register Driver 'gpio-fan'
[ 9.441024] Register Driver 'lm75'
[ 9.445526] Register Driver 'lm77'
[ 9.449579] md: linear personality registered for level -1
[ 9.455090] md: raid0 personality registered for level 0
[ 9.460379] md: raid1 personality registered for level 1
[ 9.465716] md: raid10 personality registered for level 10
[ 9.471262] md: raid6 personality registered for level 6
[ 9.476553] md: raid5 personality registered for level 5
[ 9.481885] md: raid4 personality registered for level 4
[ 9.487402] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 9.496041] device-mapper: multipath: version 1.5.1 loaded
[ 9.501571] device-mapper: multipath round-robin: version 1.0.0 loaded
[ 9.508073] device-mapper: multipath queue-length: version 0.1.0 loaded
[ 9.514694] device-mapper: multipath service-time: version 0.2.0 loaded
[ 9.521407] device-mapper: dm-log-userspace: version 1.1.0 loaded
[ 9.527478] device-mapper: raid: Loading target version 1.4.2
[ 9.533240] Register Driver 'mmcblk'
[ 9.537051] Register Driver 'leds-gpio'
[ 9.541157] leds-gpio leds-gpio: pins are not configured from the driver
[ 9.547839] orion_gpio_is_valid: invalid GPIO 12
[ 9.548231] Register Driver 'leds-ns2'
[ 9.552285] Register Driver 'leds-ns2l'
[ 9.556634] Register Driver 'leds-netxbig'
[ 9.561055] Register Driver 'mv_crypto'
[ 9.565969] Register Driver 'hid-generic'
[ 9.570248] Register Driver 'r8712u'
[ 9.574237] usbcore: registered new interface driver r8712u
[ 9.579853] Netfilter messages via NETLINK v0.30.
[ 9.584747] nf_conntrack version 0.5.0 (1901 buckets, 7604 max)
[ 9.591158] IPv4 over IPv4 tunneling driver
[ 9.596419] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.601910] TCP: cubic registered
[ 9.605258] NET: Registered protocol family 10
[ 9.610841] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.616323] sit: IPv6 over IPv4 tunneling driver
[ 9.622004] NET: Registered protocol family 17
[ 9.626455] NET: Registered protocol family 5
[ 9.631039] NET: Registered protocol family 37
[ 9.635706] VFP support v0.3: not present
[ 9.641068] console [netcon0] enabled
[ 9.644712] netconsole: network logging started
[ 9.649223] Register Driver 'gpio-keys'
[ 9.653748] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 9.660961] rtc-mv rtc-mv: setting system clock to 2013-10-17 19:00:15 UTC (1382036415)
[ 9.700687] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 9.740713] ata1.00: ATA-8: WDC WD25EZRX-00AZ6B0, 80.00A80, max UDMA/133
[ 9.747397] ata1.00: 4883781168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 9.790714] ata1.00: configured for UDMA/133
[ 9.811060] scsi 0:0:0:0: Direct-Access ATA WDC WD25EZRX-00A 80.0 PQ: 0 ANSI: 5
[ 9.819696] No LaCie disk map available
[ 9.824177] sd 0:0:0:0: [sda] 4883781168 512-byte logical blocks: (2.50 TB/2.27 TiB)
[ 9.832544] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 9.838057] sd 0:0:0:0: [sda] Write Protect is off
[ 9.842906] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 9.843053] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 9.887659] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8
[ 9.896443] sd 0:0:0:0: [sda] Attached SCSI disk
[ 10.180675] ata2: SATA link down (SStatus 0 SControl F300)
[ 10.200725] md: Skipping autodetection of RAID arrays. (raid=autodetect will force)
[ 10.244759] EXT3-fs (sda7): mounted filesystem with ordered data mode
[ 10.251225] kjournald starting. Commit interval 5 seconds
[ 10.256725] VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
[ 10.264144] Freeing init memory: 184K
[ 10.465108] EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended
[ 10.474199] EXT3-fs (sda7): using internal journal
[ 11.010879] EXT3-fs (sda1): warning: checktime reached, running e2fsck is recommended
[ 11.018769] kjournald starting. Commit interval 5 seconds
[ 11.024337] EXT3-fs (sda1): using internal journal
[ 11.040731] EXT3-fs (sda1): recovery complete
[ 11.045078] EXT3-fs (sda1): mounted filesystem with ordered data mode
[ 12.220946] kjournald starting. Commit interval 5 seconds
[ 12.226478] EXT3-fs (sda5): using internal journal
[ 12.250740] EXT3-fs (sda5): recovery complete
[ 12.255084] EXT3-fs (sda5): mounted filesystem with ordered data mode
[ 12.479881] Adding 516092k swap on /dev/sda3. Priority:-1 extents:1 across:516092k
[ 12.782257] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 12.788769] Register Driver 'orion-ehci'
[ 12.792980] orion-ehci orion-ehci.0: Marvell Orion EHCI
[ 12.798215] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 12.806026] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[ 12.830669] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 12.836658] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 12.843446] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 12.850658] usb usb1: Product: Marvell Orion EHCI
[ 12.855351] usb usb1: Manufacturer: Linux 3.9.5 ehci_hcd
[ 12.860662] usb usb1: SerialNumber: orion-ehci.0
[ 12.866013] hub 1-0:1.0: USB hub found
[ 12.869771] hub 1-0:1.0: 1 port detected
[ 12.887220] Initializing USB Mass Storage driver...
[ 12.892227] Register Driver 'usb-storage'
[ 12.896591] usbcore: registered new interface driver usb-storage
[ 12.902715] USB Mass Storage support registered.
[ 12.917332] Register Driver 'usblp'
[ 12.921261] usbcore: registered new interface driver usblp
[ 12.940406] iSCSI Enterprise Target Software - version trunk
[ 12.946347] iscsi_trgt: Registered io type fileio
[ 12.951091] iscsi_trgt: Registered io type blockio
[ 12.955864] iscsi_trgt: Registered io type nullio
[ 12.972905] Loading iSCSI transport class v2.0-870.
[ 12.985669] iscsi: registered transport (tcp)
[ 26.180699] kjournald starting. Commit interval 5 seconds
[ 26.188633] EXT3-fs (sda8): using internal journal
[ 26.230772] EXT3-fs (sda8): recovery complete
[ 26.235124] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 26.481067] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 26.746452] udevd (833): /proc/833/oom_adj is deprecated, please use /proc/833/oom_score_adj instead.
[ 28.294338] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled
[ 28.304117] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 41.184984] FAT-fs (loop0): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[ 41.211465] FAT-fs (loop0): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1175.004612] Register Driver 'rt2800usb'
[ 1175.025597] usbcore: registered new interface driver rt2800usb
[ 1521.050680] usb 1-1: new high-speed USB device number 2 using orion-ehci
[ 1521.218530] usb 1-1: New USB device found, idVendor=148f, idProduct=5370
[ 1521.225239] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1521.232363] usb 1-1: Product: 802.11 n WLAN
[ 1521.236536] usb 1-1: Manufacturer: Ralink
[ 1521.240536] usb 1-1: SerialNumber: 1.0
[ 1521.390764] usb 1-1: reset high-speed USB device number 2 using orion-ehci
[ 1521.586910] phy0 -> rt2x00_set_chip: Info - Chipset detected - rt: 5390, rf: 5370, rev: 0502.
[ 1521.630864] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'

web interface now:

T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=148f ProdID=5370 Rev=01.01
S: Manufacturer=Ralink
S: Product=802.11 n WLAN
S: SerialNumber=1.0
C: #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=450mA
I: If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2800usb
I: If#= 0 Alt= 0 #EPs= 7 Cls=ff(vend.) Sub=ff Prot=ff Driver=rt2800usb

[fvdw]

:thumbup

and can you set it up in WEP mode

for wpa(2) we need some more tools, but WEP should work with wireless tools i have sent you

[matzi]

Think we nearly made it.

I set up an old router to offer a WEP encrypted connection. Then i set up the WiGI dongle with iwconfig, ifconfig and iwlist. Result is:

root@fvdwsl-base:/ # ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr xx:xx:xx:xx:xx:xx
inet addr:xxx.xxx.xxx.xx Bcast:xxx.xxx.xxx.xxx Mask:255.255.255.0
inet6 addr: xxxx::xxxx:xxxx:xxxx:xxxx/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1486 errors:0 dropped:0 overruns:0 frame:0
TX packets:44 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:276302 (269.8 KiB) TX bytes:2656 (2.5 KiB)

Now see what the router says:



Bekannte Netzwerkgeräte - WLAN
Name IP-Adresse MAC-Adresse Datenrate Eigenschaften
- - xx:xx:xx:xx:xx:xx 54 MBit/s WEP
(The formatting is not correct here. Name=-, IP=- MAC Adress is xx......, Datenrate =54MBit/s, EIgenschaften =WEP)

Please note that I put "x" on some data but there are numbers and I double checked the numbers are correct. It means the dongle is recognized but the IP is not accepted. Never saw this, what can it mean?

Further observation:
I had LAN and WLAN ports active simultanously with different IPs.
I had access to the NAS through both IPs. Acces through the WLAN IP was noticably slower most likely because of the differnt speed 54Mbit/s - 100MBit/s.
Then I disconnected the LAN cable expecting the WLAN remaining active, but at this point the WLAN connection also stops and I have no access anynore. Replugging the cable, renewing the connections in putty reestablishes both connections.

[fvdw]

to be honest I have no idea

I helped a a while ago someone elese with a wifi dongle. he used manual setup of the ip. For dhcp you need additional commands and a dhcp client
Busybox has one build in
I need to look if I can find the notes made in that time

[Jocko]

@fvdw
I think that you find it in the function laniffunc_configure

[fvdw]

@fvdw
I think that you find it in the function laniffunc_configure

no that use a complicated php script. I also use the dhcp client form busybox in the standalone kernel. It needs also a script in /etc

[fvdw]

found it

Code: Select all

/sbin/ifconfig wlan0 up
udhcpc -t 5 -q -s /etc/simple.script

(udhcpc is sym link to busybox its already present in the firmware

the simple script you can find for example here http://git.busybox.net/busybox/tree/examples/udhcp
, but should be adapted to use only for wlan0 otherwise it will probably also renew eth0
You will need to try

I having some troubles to get wpa-suppliant compiled (needed for wpa support) sorry to keep you waiting ;)

[matzi]

Capture_1.jpg

Still the same, recognized in the router with MAC Adress but not with IP.

[fvdw]

but it has an IP, I mean you can connect to it and communicate ?