Kernel Version

[j.coudrais]

Hi,

Here we go, just installed one nwsp2, a light version, i'm now with your 13.0 firmware.
Quite a good job as usually, thank you !

Well, now i'm going to use some usb devices and drivers are not loaded in the rcS file.
I tried loading with insmod manually, but the drivers are not in the /boot directory...
I think I'm wrong with something....
I wanted to use some devices with pl2303 and FTDI...
Could you help me, please ?

[fvdw]

yes you will need some modules for ftdi and pl2303

I attached them for you

[j.coudrais]

You're the best, thank you !!

I have an issue with lsusb,
unable to initialize libusb: -99
is that normal ?

[fvdw]

yes this is normal on nwsp2 usbfs is no longer supported in new kernels and thats why it gives this message
You can use

Code: Select all

lsusb -t

that should give some output

In the next release we will incorporate a script that can be used to get info on usb-devices
I attached it for you so you can give that a try as well, it will give more output then lsusb -t

[j.coudrais]

Hi fvdw

thank you for your help.

usb-devices gives useful info, that's right...

I have a driver problem with a OneWire DS2490 usb stick
usb-devices gives that : also no driver it seems...

T: Bus=01 Lev=02 Prnt=70 Port=00 Cnt=01 Dev#= 54 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS= 8 #Cfgs= 1
P: Vendor=04fa ProdID=2490 Rev=00.02
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)

PS : I'm using the ones you gave me in the zip file (2303, FTDI and usb-serial)

[fvdw]

no kernel module for that also I can find nothing about in the kernel configuration options
It should use usb-storage module, suppose that you that still have loaded

[j.coudrais]

Thank you...

Could i use a compiled driver with this source ?
http://lxr.free-electrons.com/source/dr ... 6.39;a=arm

[fvdw]

I will look at later, so to see it is part of the kernel sources, so only need to find out which module to activate

[fvdw]

found it the kernel source under W1, its not an usb stick for storage but a one wire device with a sensor or so. Anyhow, I compiled them for you andattached the two kernel modules that you require to get it supported ;)

Lets us know if it works

[j.coudrais]

Thank you for that, but...

these 2 drivers do the job for the driver
T: Bus=01 Lev=02 Prnt=27 Port=00 Cnt=01 Dev#= 28 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS= 8 #Cfgs= 1
P: Vendor=04fa ProdID=2490 Rev=00.02
C: #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=DS9490R

But I can't request the bus 1w as I did with digitemp (a binary)...

I'lm trying to get it working with owfs that is a brower upon the 1w bus as a folder structure. (the bus is mounted as a fiel system)
I can't find any working version for this arm architecture...

I hope you can help me...