plugout.net

by **samrise** » Mon Aug 17, 2015 10:35 pm

Code: Select all: root@(none):/ # dmesg Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #42 PREEMPT Tue May 26 00:07:37 CEST 2015 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: LaCie 5Big1 Network Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 Memory policy: ECC disabled, Data cache writeback On node 0 totalpages: 32768 free_area_init_node: node 0, pgdat c03daf30, node_mem_map c03ec000 Normal zone: 256 pages used for memmap Normal zone: 0 pages reserved Normal zone: 32512 pages, LIFO batch:7 pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 pcpu-alloc: [0] 0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.83/ PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Memory: 128MB = 128MB total Memory: 125896k/125896k available, 5176k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) DMA : 0xffc00000 - 0xffe00000 ( 2 MB) vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .init : 0xc0008000 - 0xc00e6000 ( 888 kB) .text : 0xc00e6000 - 0xc03c8000 (2952 kB) .data : 0xc03c8000 - 0xc03db600 ( 78 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 Preemptable hierarchical RCU implementation. RCU-based detection of stalled CPUs is disabled. Verbose stalled-CPUs detection is disabled. NR_IRQS:64 sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok NET: Registered protocol family 16 Orion ID: MV88F5281-D0. TCLK=166666667. Orion: Applying 5281 D0 WFI workaround. net5big: powering up SATA drives net5big: turning off power-off control GPIO net5big: Flash writing is not yet supported. net5big: net5big_pci_preinit failed to gpio_request 20 pci 0000:00:00.0: [11ab:5281] type 0 class 0x000580 pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref] pci 0000:00:00.0: reg 18: [mem 0x00000000-0x07ffffff] PCI: bus0: Fast back to back transfers disabled pci 0000:01:00.0: [11ab:5281] type 0 class 0x000580 pci 0000:01:00.0: reg 10: [mem 0x00000000-0x07ffffff 64bit pref] pci 0000:01:00.0: reg 18: [mem 0x10000000-0x1fffffff 64bit pref] pci 0000:01:00.0: reg 20: [mem 0xf1000000-0xf10fffff 64bit] pci 0000:01:00.0: reg 30: [mem 0xe0000000-0xe7ffffff pref] pci 0000:01:00.0: supports D1 D2 pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot pci 0000:01:00.0: PME# disabled pci 0000:01:07.0: [11ab:6081] type 0 class 0x000100 pci 0000:01:07.0: reg 10: [mem 0x40000000-0x400fffff 64bit] pci 0000:01:07.0: reg 18: [io 0xf0100000-0xf01000ff] PCI: bus1: Fast back to back transfers enabled pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit] pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff]) pci 0000:01:07.0: BAR 2: assigned [io 0x100000-0x1000ff] pci 0000:01:07.0: BAR 2: set to [io 0x100000-0x1000ff] (PCI address [0x100000-0x1000ff]) bio: create slab <bio-0> at 0 SCSI subsystem initialized libata version 3.00 loaded. Switching to clocksource orion_clocksource NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Switched to NOHz mode on CPU #0 TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 PCI: CLS 32 bytes, default 32 NetWinder Floating Point Emulator V0.97 (double precision) msgmni has been set to 245 io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled loop: module loaded Uniform Multi-Platform E-IDE driver ide-gd driver 1.18 sata_mv 0000:01:07.0: version 1.28 sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv scsi4 : sata_mv scsi5 : sata_mv scsi6 : sata_mv scsi7 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52 ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52 ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52 ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52 ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52 ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52 ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52 ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52 sata_mv sata_mv.0: version 1.28 sata_mv sata_mv.0: slots 32 ports 5 scsi8 : sata_mv scsi9 : sata_mv scsi10 : sata_mv scsi11 : sata_mv scsi12 : sata_mv ata9: SATA max UDMA/133 irq 29 ata10: SATA max UDMA/133 irq 29 ata11: SATA max UDMA/133 irq 29 ata12: SATA max UDMA/133 irq 29 ata13: SATA max UDMA/133 irq 29 mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 mv643xx_eth smi: probed mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:88:fd:e0 netconsole: local port 6666 netconsole: local IP 192.168.1.252 netconsole: interface 'eth0' netconsole: remote port 6666 netconsole: remote IP 192.168.1.83 netconsole: remote ethernet address ff:ff:ff:ff:ff:ff netconsole: device eth0 not up yet, forcing it ata1: SATA link down (SStatus 0 SControl 300) ata2: SATA link down (SStatus 0 SControl 300) ata3: SATA link down (SStatus 0 SControl 300) ata9: failed to resume link (SControl 0) ata9: SATA link down (SStatus 0 SControl 0) ata4: SATA link down (SStatus 0 SControl 300) mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 100 Mb/s, full duplex, flow control disabled console [netcon0] enabled netconsole: network logging started aoe: AoE v47 initialised. input: gpio-keys as /devices/platform/gpio-keys/input/input0 i2c /dev entries driver at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver mv_xor mv_xor.0: Self-test copy failed compare, disabling mv_xor mv_xor.1: Self-test copy failed compare, disabling TCP cubic registered NET: Registered protocol family 17 VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0 ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-8: Hitachi HDT721010SLA360, ST6OA3AA, max UDMA/133 ata5.00: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA Hitachi HDT72101 ST6O PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 0 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 disk diskname= sda sd 4:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk ata6: SATA link down (SStatus 0 SControl 300) ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) ata10: failed to resume link (SControl 0) ata10: SATA link down (SStatus 0 SControl 0) ata11: failed to resume link (SControl 0) ata11: SATA link down (SStatus 0 SControl 0) ata12: failed to resume link (SControl 0) ata12: SATA link down (SStatus 0 SControl 0) ata13: failed to resume link (SControl 0) ata13: SATA link down (SStatus 0 SControl 0) Freeing init memory: 888K root@(none):/ #

by **samrise** » Mon Aug 17, 2015 10:37 pm

I should try with all disks on place, because console/script/etc writes firmware on the righthand disk when they are all in place.

by **fvdw** » Mon Aug 17, 2015 10:42 pm

Code: Select all: fvdw1 disk index before get_sd_name = 0 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 disk diskname= sda sd 4:0:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00 sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk

the bus number in this case 4:0:0:0 is independent of the number of disk installed, what the kernel does is assigning a drive id (sda) to this bus number regardless how many disk are installed. The bus number is linked to each slot

lets try to mount sda7

Code: Select all: mkdir /sda7 mount /dev/sda7 /sda7

if it mount look to content of /sda7

Code: Select all: ls -al /sda7

by **samrise** » Mon Aug 17, 2015 10:44 pm

Code: Select all: root@(none):/ # mkdir /sda7 root@(none):/ # mount /dev/sda7 /sda7/ root@(none):/ # ls -al /sda7/ total 112 drwxr-xr-x 23 root root 4096 Jan 1 00:00 . drwxr-xr-x 13 root root 0 Jan 1 00:18 .. lrwxrwxrwx 1 root root 20 Dec 30 2014 .mldonkey -> /share/1000/mldonkey lrwxrwxrwx 1 root root 16 Jun 26 2015 .ssh -> ../../rw_fs/.ssh drwxr-xr-x 2 root root 4096 Dec 30 2014 bin drwxr-xr-x 2 root root 4096 Dec 30 2014 bin_cab drwxr-xr-x 2 root root 4096 Sep 25 2013 boot -rw-r--r-- 1 root root 170 Aug 17 2015 boot.log drwxrwxrwx 2 root root 4096 Dec 30 2014 clunc drwxr-xr-x 6 root root 12288 Aug 17 2015 dev lrwxrwxrwx 1 root root 11 Jun 26 2015 direct-usb -> /share/1000 drwxrwxrwx 18 root root 4096 Jun 26 2015 etc drwxrwxrwx 2 root root 4096 Jan 1 00:00 fvdw-chroot drwxrwxrwx 2 root root 4096 Jun 26 2015 lacie-boot drwxr-xr-x 4 root root 4096 Nov 22 2014 lib lrwxrwxrwx 1 root root 11 Dec 30 2014 linuxrc -> bin/busybox drwx------ 2 root root 16384 Jan 3 2008 lost+found drwxr-xr-x 3 root root 4096 Dec 30 2014 mail lrwxrwxrwx 1 root root 14 Jun 26 2015 mnt -> /rw_fs/tmp/mnt drwxr-xr-x 2 root root 4096 Aug 27 2008 nowhere drwxr-xr-x 7 root root 4096 Dec 30 2014 opt drwxrwxrwx 2 root root 4096 Mar 5 2011 proc drwxr-xr-x 2 root root 4096 Jan 3 2008 root drwxr-xr-x 2 root root 4096 Jun 26 2015 rw_fs drwxr-xr-x 2 root root 4096 Jun 26 2015 sbin drwxrwxrwx 7 root root 4096 Jun 26 2015 share drwxrwxrwx 2 root root 4096 Dec 30 2014 sys lrwxrwxrwx 1 root root 10 Jun 26 2015 tmp -> /rw_fs/tmp drwxr-xr-x 22 root root 4096 Jun 26 2015 usr drwxr-xr-x 2 root root 4096 Jun 26 2015 var root@(none):/ #

by **fvdw** » Mon Aug 17, 2015 10:47 pm

thats what it should be

what is the content of boot.log

Code: Select all: cat /sda7/boot.log

and the content of folder lacie-boot

Code: Select all: ls -al /sda7/lacie-boot

by **samrise** » Mon Aug 17, 2015 10:49 pm

Code: Select all: root@(none):/ # cat /sda7/boot.log start boot log detect and set platform 5big1 UIMAGE-395-5BIG1-25 5big1 mount dev/pts update dev nodes booting using sda1 file system... else loop1 finished rcS finished root@(none):/ # ls -al /sda7/lacie-boot/ total 8 drwxrwxrwx 2 root root 4096 Jun 26 2015 . drwxr-xr-x 23 root root 4096 Jan 1 00:00 .. -rw-r--r-- 1 root root 0 Jun 26 2015 sda1boot root@(none):/ #

by **fvdw** » Mon Aug 17, 2015 10:51 pm

ok
mount sda1 and check content

Code: Select all: mkdir /sda1 mount /dev/sda1 /sda1 ls -al /sda1 cat /sda1/boot.log

by **samrise** » Mon Aug 17, 2015 10:54 pm

Code: Select all: root@(none):/ # mkdir /sda1 root@(none):/ # mount /dev/sda1 sda1 sda10 root@(none):/ # mount /dev/sda1 /sda1/ root@(none):/ # ls -la /sda1/ total 12096 drwxr-xr-x 25 root root 4096 Aug 17 2015 . drwxr-xr-x 14 root root 0 Jan 1 00:27 .. -rw------- 1 root root 8057 Aug 17 2015 .ash_history lrwxrwxrwx 1 root root 20 Dec 30 2014 .mldonkey -> /share/1000/mldonkey lrwxrwxrwx 1 root root 16 Aug 17 2015 .ssh -> ../../rw_fs/.ssh -rw-r--r-- 1 root root 10180096 Aug 17 2015 5big1-3142-modules.tar -rw-r--r-- 1 root root 2046104 Aug 17 2015 UIMAGE-3142-5BIG1-1 drwxr-xr-x 2 root root 4096 Dec 30 2014 bin drwxr-xr-x 2 root root 4096 Dec 30 2014 bin_cab drwxr-xr-x 2 root root 4096 Sep 25 2013 boot -rw-r--r-- 1 root root 3475 Aug 17 2015 boot.log -rw-r--r-- 1 root root 284 Aug 17 2015 cat drwxrwxrwx 2 root root 4096 Dec 30 2014 clunc drwxr-xr-x 6 root root 12288 Aug 17 2015 dev lrwxrwxrwx 1 root root 11 Aug 17 2015 direct-usb -> /share/1000 drwxrwxrwx 18 root root 4096 Aug 17 2015 etc -rw-r--r-- 1 root root 0 Nov 16 2011 help drwxrwxrwx 2 root root 4096 Aug 17 2015 lacie-boot drwxr-xr-x 4 root root 4096 Nov 22 2014 lib lrwxrwxrwx 1 root root 11 Dec 30 2014 linuxrc -> bin/busybox drwx------ 2 root root 16384 Jan 3 2008 lost+found drwxr-xr-x 3 root root 4096 Dec 30 2014 mail lrwxrwxrwx 1 root root 14 Aug 17 2015 mnt -> /rw_fs/tmp/mnt drwxr-xr-x 2 root root 4096 Aug 27 2008 nowhere drwxr-xr-x 7 root root 4096 Dec 30 2014 opt drwxrwxrwx 2 root root 4096 Mar 5 2011 proc drwxr-xr-x 2 root root 4096 Jan 3 2008 root drwxr-xr-x 2 root root 4096 Nov 16 2011 rw_fs drwxr-xr-x 2 root root 4096 Aug 17 2015 sbin drwxr-xr-x 2 root root 4096 Jan 1 00:00 sda7-tmp drwxrwxrwx 8 root root 4096 Jun 27 2015 share drwxrwxrwx 2 root root 4096 Dec 30 2014 sys drwxr-xr-x 2 root root 4096 Aug 10 2015 temp drwxr-xr-x 2 root root 4096 Aug 17 2015 test lrwxrwxrwx 1 root root 10 Aug 17 2015 tmp -> /rw_fs/tmp drwxr-xr-x 22 root root 4096 Aug 17 2015 usr drwxr-xr-x 2 root root 4096 Aug 17 2015 var root@(none):/ # cat /sda1/boot.log start boot log detect and set platform 5big1 UIMAGE-395-5BIG1-25 5big1 mount dev/pts update dev nodes booting using sda1 root file system... make dev node for buttons... make dev node for tun device... enable IP forwarding... start buttons control daemon device = 5big1 source = buttons-nwsp2 buttons-nwsp2 daemon started Tue Aug 18 00:08:52 WEST 2015 create temporary passwd file run udevstart to update dev nodes when necessary inserting kernel modules: modprobe: module 'cifs' not found modprobe: module 'isofs' not found modprobe: module 'ntfs' not found modprobe: module 'fuse' not found modprobe: module 'usblp' not found modprobe: module 'nfs' not found modprobe: module 'nfsd' not found modprobe: module 'iscsi_trgt' not found modprobe: module 'iscsi_tcp' not found modprobe: module 'videodev' not found modprobe: module 'v4l2_int_device' not found modprobe: module 'v4l2_common' not found modprobe: module 'uvcvideo' not found modprobe: module 'linear' not found modprobe: module 'raid0' not found modprobe: module 'raid1' not found modprobe: module 'raid10' not found modprobe: module 'raid456' not found modprobe: module 'dm_mod' not found modprobe: module 'dm_crypt' not found modprobe: module 'dm_multipath' not found modprobe: module 'dm_round_robin' not found modprobe: module 'dm_queue_length' not found modprobe: module 'dm_service_time' not found modprobe: module 'dm_snapshot' not found modprobe: module 'dm_mirror' not found modprobe: module 'dm_log' not found modprobe: module 'dm_region_hash' not found modprobe: module 'dm_log_userspace' not found modprobe: module 'dm_raid' not found modprobe: module 'raid_class' not found create temporary group file mount: unknown filesystem type 'nfsd' configure loopback netwerk interface setting reboot and standby 5big1 rebootd-isp1 5big1 standbyd-isp1 start fan fan5big daemon started starting php based setup routines step 1 * Finishing restore RAID devices... [ OK ] * Found XML database configuration file... [ OK ] * Updating Disks database... [ OK ] * Starting mount of volumes... - Mounting volume Vol-A: [ Fail ] * Finishing mount of volumes... [ Fail ] * Starting udevd... [ OK ] * Generating Hosts File... [ OK ] * Configuring System Hostname... [ OK ] * Configuring LAN interface... [ OK ] * Initializing Timezone... [ OK ] * Starting web server... [ OK ] * Starting mount of internal USB ... * Finishing mount internal USB ... [ OK ] * Configuring Disks... [ OK ] * Configuring Samba... [ OK ] * Configuring System Users... Root password: use default password Set users, linux and samba accounts [ OK ] * Starting syncawayd... [ OK ] * Starting Fvdw-sl Discovery Daemon... [ OK ] start rpcbind service starting php based setup routines step 2 * Starting dropbear... [ OK ] * Kill temporary dropbear... [ OK ] starting php based setup routines step 3 * Starting daemon update Hosts File... [ OK ] * Starting Disk Temperature Guard... [ OK ] * Starting mount of remote shares... * Finishing mount shares... [ OK ] starting php based setup routines step banner *** fvdw-sl NAS firmware This is fvdw-sl version: fvdw-sl 16.0 built on: Dec 28 2014 LAN IP address: 192.168.1.91 (static) Port configuration: LAN -> eth0 php based setup routines finished web permission on resolv.conf set device tuning for dms performance else loop1 finished rcS finished root@(none):/ #

by **fvdw** » Mon Aug 17, 2015 11:01 pm

also ok (except loading of the modules seems to have failed :hammerhead

Code: Select all: ls -al /lib/modules

I doubt but it could be that the kernel has gone corrupt in the the transfer process
md5sum UIMAGE-3142-5BIG1-1:
bf2e989e82b24259f18de13755091bba

I am not sure if the command md5sum is working on standalone kernel md5sum

Code: Select all: md5sum /sda1/UIMAGE-3142-5BIG1-1

by **samrise** » Mon Aug 17, 2015 11:04 pm

Code: Select all: root@(none):/ # md5sum /sda1/UIMAGE-3142-5BIG1-1 bf2e989e82b24259f18de13755091bba /sda1/UIMAGE-3142-5BIG1-1 root@(none):/ # cd /lib/ root@(none):/lib # ls root@(none):/lib # ls -la total 0 drwxr-xr-x 2 root root 0 May 25 2015 . drwxr-xr-x 14 root root 0 Jan 1 00:27 .. root@(none):/lib #

plugout.net

Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Re: Problems with raid5

Who is online