lacie 5 big network v.1 please support for fvdw

[fvdw]

no there is no need for backup
we only replace the kernel. if the new kernel doesn't work you can write back the old linux 26394 #20 kernel

kernel and kernel modules are sent by pm

[taetae]

I unpacked the modules:

Code: Select all

 /share/1000/Terra # tar -xvf modules-5big1-395-27dec13.tar -C /
./
./lib/
./lib/modules/
./lib/modules/3.9.5/
./lib/modules/3.9.5/isofs.ko
./lib/modules/3.9.5/v4l2-int-device.ko
./lib/modules/3.9.5/usblp.ko
./lib/modules/3.9.5/v4l2-common.ko
./lib/modules/3.9.5/cifs.ko
./lib/modules/3.9.5/nfsd.ko
./lib/modules/3.9.5/uvcvideo.ko
./lib/modules/3.9.5/nfs.ko
./lib/modules/3.9.5/fuse.ko
./lib/modules/3.9.5/videodev.ko
./lib/modules/3.9.5/ntfs.ko

and I copied the kernel in the public folder and then giving the command:

Code: Select all

dd if = uImage-395-11-NWSP2CL-5BIG1 of = / dev/sda6

Code: Select all

/share/1000/Terra # dd if=UIMAGE-395-NWSP2CL-5BIG1-11 of=/dev/sda6
3793+1 records in
3793+1 records out
1942040 bytes (1.9MB) copied, 0.145934 seconds, 12.7MB/s
/share/1000/Terra #

Reboot:

Code: Select all

        __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: RD-88F5281-LaCie LE

U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9

U-Boot code: 00200000 -> 0026FFF0  BSS: -> 00283280

Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  32bit width
[4096kB@ffc00000] Flash:  4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
*** Warning - bad CRC, using default environment


CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.

USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net:   egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot:  0
Waiting for LUMP (5)
no lump receive; continuing

Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
  Device 0: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0218180
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 1: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0410979
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 2: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0424246
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 3: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0219436
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 4: OK
Model: WDC WD5000AADS-00S9B0                    Firm: 01.00A01 Ser#:      WD-WCAV90478832
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)


Loading from IDE device 0, partition 6: Name: hda6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 1, partition 6: Name: hdb6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 2, partition 6: Name: hdc6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 3, partition 6: Name: hdd6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 4, partition 6: Name: hde6
  Type: U-Boot
   Image Name:   Linux-3.9.5
   Created:      2013-12-27   9:26:26 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1941976 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00400000 ...
   Image Name:   Linux-3.9.5
   Created:      2013-12-27   9:26:26 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1941976 Bytes =  1.9 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.



[fvdw]

so nothing after booting the kernel I assume ?

[taetae]

there is a problem and it seems to me that already happened once with a kernel, but it escapes me what did you do to solve it seems to me that it was some command in the kernel that was not

<font><font>così nulla dopo l'avvio del kernel suppongo?</font></font>

nothing, freezes well ....

[fvdw]

the problem that time was that the kernel was too big and did overwrite u-boot when it was loaded.

I thought I had made it small enough, need to check what the max size can be.
Do you remember which standalone kernel 92.6.39.4) you could load and run ?

[fvdw]

I will compile one with usb support as module,that will make it smaller. If that works we will need to add loading some modules later after boot to get usb support back

[taetae]

UIMAGE-395-NWSP2CL-5BIG1-12



nothing, freezes well ....



UIMAGE-26394-5BIG1-20 size 1828 kb vs UIMAGE-395-NWSP2CL-5BIG1-12 1864kb

[fvdw]

I assume you get that output from the serial console ?

[fvdw]

a new kernel is being prepared, I disabled some older stuff, lets see if that helps

[taetae]

is certainly ok and mounted serial .....
look your kernel tries ... I'm here