I will replace the database and restarted after giving permissions and photographed screen is made with the new database that I've been through
23:56
I tried to edit xml seeing what you had posted but I know that I have corrupt and now I have to find a way to replace it since I have not access to ssh and web interface
plugout.net
Alternative firmware fvdw-sl
SPD8020, Lacie network space vs1,vs2 and max, 5big version 1&2, 2big version 1&2, internet space vs1, edmini_v2, D2 network version 1&2, raspberry Pi b
lacie 5 big network v.1 please support for fvdw
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Mon Nov 04, 2013 10:29 pm
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by fvdw » Mon Nov 04, 2013 11:03 pm
you should not edit it, just use the default one that I have sent you.
Anyhow if you do not have ssh access anymore when 15-0 is running then you can do this
boot the 5big1 using fvdw-sl console and standalone kernel
Unpack the default database file in the archive in the tftp folder of the fvdw-sl console
In the telnet client give the commands
Now we copy the new data base file
(replace ip-pc in this command by the ip address running the fvdw-sl console)
after that perform
Anyhow if you do not have ssh access anymore when 15-0 is running then you can do this
boot the 5big1 using fvdw-sl console and standalone kernel
Unpack the default database file in the archive in the tftp folder of the fvdw-sl console
In the telnet client give the commands
- Code: Select all
mkdir /sda5
mount /dev/sda5 /sda5
Now we copy the new data base file
- Code: Select all
tftp -r nas_conf_db.xml -l /sda5/etc/nas_conf_db.xml -g ip-pc
(replace ip-pc in this command by the ip address running the fvdw-sl console)
after that perform
- Code: Select all
sync
reboot -f
You do not have the required permissions to view the files attached to this post.
- fvdw
- Site Admin - expert
- Posts: 13471
- Joined: Tue Apr 12, 2011 2:30 pm
- Location: Netherlands
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Tue Nov 05, 2013 12:42 pm
replaced with your last attachment .....
no visible changes ... on the web
Now I try to mount the SD8 and see what happens .... coming soon
14:09
mmmm......
:fists :fists :fists
no visible changes ... on the web
- Code: Select all
(none) login: root
Password:
root@(none):/ # mkdir /sda5
root@(none):/ # mount /dev/sda5 /sda5
root@(none):/ # tftp -r nas_conf_db.xml -l /sda5/etc/nas_conf_db.xml -g 192.168.1.29
nas_conf_db.xml 100% |************************************************************| 3420 0:00:00 ETA
root@(none):/ # sync
root@(none):/ # reboot
root@(none):/ # reboot -f
Now I try to mount the SD8 and see what happens .... coming soon
14:09
mmmm......
:fists :fists :fists
You do not have the required permissions to view the files attached to this post.
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by fvdw » Tue Nov 05, 2013 2:46 pm
:disapprove
apparently the boot script to set up the hard disk in the data base doesn't like a 5big1 and it corrupts the database.
We need to speak with Jocko as he programmed that script that automatic updates the database for mutiple disks
The script uses specific commands but because the 5big1 has a pci interface for the disks, while the other lacie so far don't have that, the script seems not to get the right information to indentify the disks and set up the database.
Jocko is not around for a few days but he will be back soon I expect.
This evening i have no time due to family business.
Sorry to keep you waiting tatae, but this will be solved don't worry
apparently the boot script to set up the hard disk in the data base doesn't like a 5big1 and it corrupts the database.
We need to speak with Jocko as he programmed that script that automatic updates the database for mutiple disks
The script uses specific commands but because the 5big1 has a pci interface for the disks, while the other lacie so far don't have that, the script seems not to get the right information to indentify the disks and set up the database.
Jocko is not around for a few days but he will be back soon I expect.
This evening i have no time due to family business.
Sorry to keep you waiting tatae, but this will be solved don't worry
- fvdw
- Site Admin - expert
- Posts: 13471
- Joined: Tue Apr 12, 2011 2:30 pm
- Location: Netherlands
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Tue Nov 05, 2013 8:59 pm
quiet I know we're doing the tests and little by little I learn a lot from what you made me do ... I just hope that you do not waste time and that what we do can be useful to others ... I'm here so configuring the pc i can access it remotely from a distance because I'm away from home for work ... I'm here when you need;-)
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by fvdw » Tue Nov 05, 2013 9:40 pm
hi tatae
until Jocko returns to adapt the script we can do following trial
I made a special database for you based on the serial output with the info of the 5 disks that you have in the 5big1.
You need to install this database file in the system folder /rw_fs/etc
Using winscp is the easiest way to do this.
Attached the trial database. It has entries for all 5 diks (sda 500GB and sdb,sdc,sdd,sde each 2 TB)
To prevent that the firmware overwrite this file and fails to store the right data we will temporarily replace the script that does this by a dummy script. This script will leave the database as it is, a dummy script.
The script that updates the database at boot has the name "dm_update_single_db.finc"
This script is located in the system folder /etc/finc
You need to replace it by the dummy version.
In the attachment you will find the adapated version.
You need to overwrite the existing file with this one.
You can copy it to /etc/finc using winscp in the same way you copied the database, but only write it to the folder /etc/finc
(the database goes into /rw_fs/etc)
ps this is a temporarily solution to see if it it now displays the disk. if so we still need to make modifications. Now the 2TB have only one partition with number 1. I prefer the have on each disk 1 partition but with number 8. Also they need to be formatted in etx3. Did you format them your self ? I assume not. If that is the case then probably they will be formatted in ntfs and they will not work properly in the firmware. But that is of later concern lets first try if you can see the drives in the web-interface when using the attached files.
if it it works then we are going to repartition these 2 TB disk and re-format them
until Jocko returns to adapt the script we can do following trial
I made a special database for you based on the serial output with the info of the 5 disks that you have in the 5big1.
You need to install this database file in the system folder /rw_fs/etc
Using winscp is the easiest way to do this.
Attached the trial database. It has entries for all 5 diks (sda 500GB and sdb,sdc,sdd,sde each 2 TB)
To prevent that the firmware overwrite this file and fails to store the right data we will temporarily replace the script that does this by a dummy script. This script will leave the database as it is, a dummy script.
The script that updates the database at boot has the name "dm_update_single_db.finc"
This script is located in the system folder /etc/finc
You need to replace it by the dummy version.
In the attachment you will find the adapated version.
You need to overwrite the existing file with this one.
You can copy it to /etc/finc using winscp in the same way you copied the database, but only write it to the folder /etc/finc
(the database goes into /rw_fs/etc)
ps this is a temporarily solution to see if it it now displays the disk. if so we still need to make modifications. Now the 2TB have only one partition with number 1. I prefer the have on each disk 1 partition but with number 8. Also they need to be formatted in etx3. Did you format them your self ? I assume not. If that is the case then probably they will be formatted in ntfs and they will not work properly in the firmware. But that is of later concern lets first try if you can see the drives in the web-interface when using the attached files.
if it it works then we are going to repartition these 2 TB disk and re-format them
You do not have the required permissions to view the files attached to this post.
- fvdw
- Site Admin - expert
- Posts: 13471
- Joined: Tue Apr 12, 2011 2:30 pm
- Location: Netherlands
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Wed Nov 06, 2013 10:17 am
:rock :rock
- Code: Select all
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: RD-88F5281-LaCie LE
U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9
U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280
Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 32bit width
[4096kB@ffc00000] Flash: 4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
*** Warning - bad CRC, using default environment
CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net: egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot: 0
Marvell>> boot
Waiting for LUMP (5)
no lump receive; continuing
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0410979
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0218180
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 2: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0424246
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0219436
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: WDC WD5000AADS-00S9B0 Firm: 01.00A01 Ser#: WD-WCAV90478832
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
Loading from IDE device 4, partition 6: Name: hde6
Type: U-Boot
Image Name: Linux-2.6.39.4
Created: 2013-09-23 18:39:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1871800 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-2.6.39.4
Created: 2013-09-23 18:39:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1871800 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.5.4 (GCC) ) #20 PREEMPT Mon Sep 23 19:39:28 GMT+1 2013
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125992k/125992k available, 5080k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0028000 ( 128 kB)
.text : 0xc0028000 - 0xc03a6000 (3576 kB)
.data : 0xc03a6000 - 0xc03c1a40 ( 111 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
net5big: powering up SATA drives
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff])
pci 0000:01:07.0: BAR 2: assigned [io 0x100000-0x1000ff]
pci 0000:01:07.0: BAR 2: set to [io 0x100000-0x1000ff] (PCI address [0x100000-0x1000ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv 0000:01:07.0: version 1.28
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:8b:60:2b
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
mv_xor mv_xor.1: Self-test copy failed compare, disabling
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 37
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
rtc-rs5c372 0-0032: setting system clock to 2013-11-08 02:14:58 UTC (1383876898)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 0
fvdw2 disk indexfvdw 0
fvdw3 disk indexfvdw 4
fvdw4 disk diskname= sde
sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sde] 4096-byte physical blocks
sd 0:0:0:0: [sde] Write Protect is off
sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 1
fvdw2 disk indexfvdw 1
fvdw3 disk indexfvdw 3
fvdw4 disk diskname= sdd
sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sde: sde1
sd 1:0:0:0: [sdd] 4096-byte physical blocks
sd 0:0:0:0: [sde] Attached SCSI disk
sd 1:0:0:0: [sdd] Write Protect is off
sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 2
fvdw2 disk indexfvdw 2
fvdw3 disk indexfvdw 2
fvdw4 disk diskname= sdc
sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:0:0:0: [sdd] Attached SCSI disk
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 3
fvdw2 disk indexfvdw 3
fvdw3 disk indexfvdw 1
fvdw4 disk diskname= sdb
sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 3:0:0:0: [sdb] 4096-byte physical blocks
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5
fvdw1 disk index 4
fvdw2 disk indexfvdw 4
fvdw3 disk indexfvdw 0
fvdw4 disk diskname= sda
sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: [sda] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
EXT3-fs (sda7): recovery required on readonly filesystem
EXT3-fs (sda7): write access will be enabled during recovery
EXT3-fs: barriers not enabled
EXT3-fs (sda7): recovery complete
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:71.
Freeing init memory: 128K
start rcS
set global environment params
mount proc
remount root file system rw
EXT3-fs (sda7): warning: checktime reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
mount sysfs
start boot log
detect and set platform
unknown
update dev nodes
booting using root file system...
make dev node for buttons...
mkdir: can't create directory '/dev/input': File exists
mknod: /dev/input/event0: File exists
make dev node for tun device...
mknod: /dev/net/tun: File exists
enable IP forwarding...
start buttons control daemon
/etc/init.d/rcS: line 522: /usr/sbin/buttonsd: Permission denied
create temporary passwd file
run udevstart to update dev nodes when necessary
mkdir: can't create directory 'rw_fs': File exists
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Setting up swapspace version 1, size = 526413824 bytes
UUID=54af57db-375c-4a2b-9b28-4f9b5f63b999
Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k
inserting kernel modules:
NTFS driver 2.1.30 [Flags: R/W MODULE].
fuse init (API version 7.16)
usbcore: registered new interface driver usblp
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
iSCSI Enterprise Target Software - version trunk
iscsi_trgt: Registered io type fileio
iscsi_trgt: Registered io type blockio
iscsi_trgt: Registered io type nullio
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
Usage: mount -V : print version
mount -h : print this help
mount : list mounted filesystems
mount -l : idem, including volume labels
So far the informational part. Next the mounting.
The command is `mount [-t fstype] something somewhere'.
Details found in /etc/fstab may be omitted.
mount -a [-t|-O] ... : mount all stuff from /etc/fstab
mount device : mount device at the known place
mount directory : mount known device here
mount -t type dev dir : ordinary mount command
Note that one does not really mount a device, one mounts
a filesystem (of the given type) found on the device.
One can also mount an already visible directory tree elsewhere:
mount --bind olddir newdir
or move a subtree:
mount --move olddir newdir
One can change the type of mount containing the directory dir:
mount --make-shared dir
mount --make-slave dir
mount --make-private dir
mount --make-unbindable dir
One can change the type of all the mounts in a mount subtree
containing the directory dir:
mount --make-rshared dir
mount --make-rslave dir
mount --make-rprivate dir
mount --make-runbindable dir
A device can be given by name, say /dev/hda1 or /dev/cdrom,
or by label, using -L label or by uuid, using -U uuid .
Other options: [-nfFrsvw] [-o options] [-p passwdfd].
For many more details, say man 8 mount .
configure loopback network interface
setting reboot and standby
starting php based setup routines step 1
sudo: /usr/sbin/lsscsi: command not found
sudo: /usr/sbin/lsscsi: command not found
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
NTFS volume version 3.1.
NTFS-fs error (device sdb1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdc1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdd1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sde1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
udevd (820): /proc/820/oom_adj is deprecated, please use /proc/820/oom_score_adj instead.
passwd[848]: password for `dummy' changed by user `root'
API[2013/11/08 02:15:46] userfunc_users_commit.finc(141)[737]: userfunc_users_commit: no smb user for dummy.
start portmap service
starting php based setup routines step2
starting php based setup routines step3
starting php based setup routines step banner
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
------------------------
rcS finished
------------------------
list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = unknown
source =
Fri Nov 8 03:15:07 GMT+1 2013
create temporary passwd file
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
setting reboot and standby
unknown
unknown
starting php based setup routines step 1
* Found XML database configuration file... [ OK ]
* Configuring Disks... [ OK ]
* Starting mount of volumes...
- Mounting volume Disk-a: [ OK ]
- Mounting volume Disk-b: [ OK ]
- Mounting volume Disk-c: [ OK ]
- Mounting volume Disk-d: [ OK ]
- Mounting volume Disk-e: [ OK ]
* Finishing mount of volumes... [ OK ]
* Generating Hosts File... [ OK ]
* Configuring System Hostname... [ OK ]
* Configuring Samba... [ OK ]
* Configuring LAN interface... [ OK ]
* Starting udevd... [ OK ]
* Starting web server... [ OK ]
* Initializing Timezone... [ OK ]
* Configuring Samba... [ OK ]
* Configuring System Users...
Root password: use default password
Set users, linux and samba accounts [ OK ]
* Starting Fvdw-sl Discovery Daemon... [ OK ]
start portmap service
starting php based setup routines step 2
* Starting dropbear... [ OK ]
* Kill temporary dropbear... [ OK ]
starting php based setup routines step 3
* Starting daemon update Hosts File... [ OK ]
starting php based setup routines step banner
*** fvdw-sl NAS firmware
This is fvdw-sl version: fvdw-sl 15.0
built on: September 30 2013
LAN IP address: 192.168.1.71 (DHCP)
Port configuration:
LAN -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
rcS finished
/bin/sh: can't access tty; job control turned off
~ #
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Wed Nov 06, 2013 10:17 am
:rock :rock
- Code: Select all
▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: RD-88F5281-LaCie LE
U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9
U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280
Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 32bit width
[4096kB@ffc00000] Flash: 4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
*** Warning - bad CRC, using default environment
CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net: egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot: 0
Marvell>> boot
Waiting for LUMP (5)
no lump receive; continuing
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0410979
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0218180
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 2: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0424246
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0219436
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: WDC WD5000AADS-00S9B0 Firm: 01.00A01 Ser#: WD-WCAV90478832
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
Loading from IDE device 4, partition 6: Name: hde6
Type: U-Boot
Image Name: Linux-2.6.39.4
Created: 2013-09-23 18:39:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1871800 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-2.6.39.4
Created: 2013-09-23 18:39:53 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1871800 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.5.4 (GCC) ) #20 PREEMPT Mon Sep 23 19:39:28 GMT+1 2013
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125992k/125992k available, 5080k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0028000 ( 128 kB)
.text : 0xc0028000 - 0xc03a6000 (3576 kB)
.data : 0xc03a6000 - 0xc03c1a40 ( 111 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
net5big: powering up SATA drives
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff])
pci 0000:01:07.0: BAR 2: assigned [io 0x100000-0x1000ff]
pci 0000:01:07.0: BAR 2: set to [io 0x100000-0x1000ff] (PCI address [0x100000-0x1000ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv 0000:01:07.0: version 1.28
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:8b:60:2b
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
mv_xor mv_xor.1: Self-test copy failed compare, disabling
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 37
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
rtc-rs5c372 0-0032: setting system clock to 2013-11-08 02:14:58 UTC (1383876898)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 0
fvdw2 disk indexfvdw 0
fvdw3 disk indexfvdw 4
fvdw4 disk diskname= sde
sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sde] 4096-byte physical blocks
sd 0:0:0:0: [sde] Write Protect is off
sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 1
fvdw2 disk indexfvdw 1
fvdw3 disk indexfvdw 3
fvdw4 disk diskname= sdd
sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sde: sde1
sd 1:0:0:0: [sdd] 4096-byte physical blocks
sd 0:0:0:0: [sde] Attached SCSI disk
sd 1:0:0:0: [sdd] Write Protect is off
sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 2
fvdw2 disk indexfvdw 2
fvdw3 disk indexfvdw 2
fvdw4 disk diskname= sdc
sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:0:0:0: [sdd] Attached SCSI disk
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 3
fvdw2 disk indexfvdw 3
fvdw3 disk indexfvdw 1
fvdw4 disk diskname= sdb
sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 3:0:0:0: [sdb] 4096-byte physical blocks
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5
fvdw1 disk index 4
fvdw2 disk indexfvdw 4
fvdw3 disk indexfvdw 0
fvdw4 disk diskname= sda
sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: [sda] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
EXT3-fs (sda7): recovery required on readonly filesystem
EXT3-fs (sda7): write access will be enabled during recovery
EXT3-fs: barriers not enabled
EXT3-fs (sda7): recovery complete
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:71.
Freeing init memory: 128K
start rcS
set global environment params
mount proc
remount root file system rw
EXT3-fs (sda7): warning: checktime reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
mount sysfs
start boot log
detect and set platform
unknown
update dev nodes
booting using root file system...
make dev node for buttons...
mkdir: can't create directory '/dev/input': File exists
mknod: /dev/input/event0: File exists
make dev node for tun device...
mknod: /dev/net/tun: File exists
enable IP forwarding...
start buttons control daemon
/etc/init.d/rcS: line 522: /usr/sbin/buttonsd: Permission denied
create temporary passwd file
run udevstart to update dev nodes when necessary
mkdir: can't create directory 'rw_fs': File exists
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Setting up swapspace version 1, size = 526413824 bytes
UUID=54af57db-375c-4a2b-9b28-4f9b5f63b999
Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k
inserting kernel modules:
NTFS driver 2.1.30 [Flags: R/W MODULE].
fuse init (API version 7.16)
usbcore: registered new interface driver usblp
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
iSCSI Enterprise Target Software - version trunk
iscsi_trgt: Registered io type fileio
iscsi_trgt: Registered io type blockio
iscsi_trgt: Registered io type nullio
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
Usage: mount -V : print version
mount -h : print this help
mount : list mounted filesystems
mount -l : idem, including volume labels
So far the informational part. Next the mounting.
The command is `mount [-t fstype] something somewhere'.
Details found in /etc/fstab may be omitted.
mount -a [-t|-O] ... : mount all stuff from /etc/fstab
mount device : mount device at the known place
mount directory : mount known device here
mount -t type dev dir : ordinary mount command
Note that one does not really mount a device, one mounts
a filesystem (of the given type) found on the device.
One can also mount an already visible directory tree elsewhere:
mount --bind olddir newdir
or move a subtree:
mount --move olddir newdir
One can change the type of mount containing the directory dir:
mount --make-shared dir
mount --make-slave dir
mount --make-private dir
mount --make-unbindable dir
One can change the type of all the mounts in a mount subtree
containing the directory dir:
mount --make-rshared dir
mount --make-rslave dir
mount --make-rprivate dir
mount --make-runbindable dir
A device can be given by name, say /dev/hda1 or /dev/cdrom,
or by label, using -L label or by uuid, using -U uuid .
Other options: [-nfFrsvw] [-o options] [-p passwdfd].
For many more details, say man 8 mount .
configure loopback network interface
setting reboot and standby
starting php based setup routines step 1
sudo: /usr/sbin/lsscsi: command not found
sudo: /usr/sbin/lsscsi: command not found
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
NTFS volume version 3.1.
NTFS-fs error (device sdb1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdc1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdd1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sde1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
udevd (820): /proc/820/oom_adj is deprecated, please use /proc/820/oom_score_adj instead.
passwd[848]: password for `dummy' changed by user `root'
API[2013/11/08 02:15:46] userfunc_users_commit.finc(141)[737]: userfunc_users_commit: no smb user for dummy.
start portmap service
starting php based setup routines step2
starting php based setup routines step3
starting php based setup routines step banner
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
------------------------
rcS finished
------------------------
list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = unknown
source =
Fri Nov 8 03:15:07 GMT+1 2013
create temporary passwd file
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
setting reboot and standby
unknown
unknown
starting php based setup routines step 1
* Found XML database configuration file... [ OK ]
* Configuring Disks... [ OK ]
* Starting mount of volumes...
- Mounting volume Disk-a: [ OK ]
- Mounting volume Disk-b: [ OK ]
- Mounting volume Disk-c: [ OK ]
- Mounting volume Disk-d: [ OK ]
- Mounting volume Disk-e: [ OK ]
* Finishing mount of volumes... [ OK ]
* Generating Hosts File... [ OK ]
* Configuring System Hostname... [ OK ]
* Configuring Samba... [ OK ]
* Configuring LAN interface... [ OK ]
* Starting udevd... [ OK ]
* Starting web server... [ OK ]
* Initializing Timezone... [ OK ]
* Configuring Samba... [ OK ]
* Configuring System Users...
Root password: use default password
Set users, linux and samba accounts [ OK ]
* Starting Fvdw-sl Discovery Daemon... [ OK ]
start portmap service
starting php based setup routines step 2
* Starting dropbear... [ OK ]
* Kill temporary dropbear... [ OK ]
starting php based setup routines step 3
* Starting daemon update Hosts File... [ OK ]
starting php based setup routines step banner
*** fvdw-sl NAS firmware
This is fvdw-sl version: fvdw-sl 15.0
built on: September 30 2013
LAN IP address: 192.168.1.71 (DHCP)
Port configuration:
LAN -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
rcS finished
/bin/sh: can't access tty; job control turned off
~ #
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Wed Nov 06, 2013 10:20 am
mmmmm
- Code: Select all
~ # dmesg
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.5.4 (GCC) ) #20 PREEMPT Mon Sep 23 19:39:28 GMT+1 2013
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 32768
free_area_init_node: node 0, pgdat c03c1378, node_mem_map c03d4000
Normal zone: 256 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 32512 pages, LIFO batch:7
pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
pcpu-alloc: [0] 0
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125992k/125992k available, 5080k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0028000 ( 128 kB)
.text : 0xc0028000 - 0xc03a6000 (3576 kB)
.data : 0xc03a6000 - 0xc03c1a40 ( 111 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
net5big: powering up SATA drives
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
pci 0000:00:00.0: [11ab:5281] type 0 class 0x000580
pci 0000:00:00.0: reg 10: [mem 0xf1000000-0xf10fffff 64bit pref]
pci 0000:00:00.0: reg 18: [mem 0x00000000-0x07ffffff]
PCI: bus0: Fast back to back transfers disabled
pci 0000:01:00.0: [11ab:5281] type 0 class 0x000580
pci 0000:01:00.0: reg 10: [mem 0x00000000-0x07ffffff 64bit pref]
pci 0000:01:00.0: reg 18: [mem 0x10000000-0x1fffffff 64bit pref]
pci 0000:01:00.0: reg 20: [mem 0xf1000000-0xf10fffff 64bit]
pci 0000:01:00.0: reg 30: [mem 0xe0000000-0xe7ffffff pref]
pci 0000:01:00.0: supports D1 D2
pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:01:07.0: [11ab:6081] type 0 class 0x000100
pci 0000:01:07.0: reg 10: [mem 0x40000000-0x400fffff 64bit]
pci 0000:01:07.0: reg 18: [io 0xf0100000-0xf01000ff]
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff])
pci 0000:01:07.0: BAR 2: assigned [io 0x100000-0x1000ff]
pci 0000:01:07.0: BAR 2: set to [io 0x100000-0x1000ff] (PCI address [0x100000-0x1000ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
PCI: CLS 32 bytes, default 32
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv 0000:01:07.0: version 1.28
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:8b:60:2b
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
mv_xor mv_xor.1: Self-test copy failed compare, disabling
Registered led device: net5big:blink:front
Registered led device: net5big:red:front
Registered led device: net5big:blue:front
Registered led device: net5big:red:sata0
Registered led device: net5big:red:sata1
Registered led device: net5big:red:sata2
Registered led device: net5big:red:sata3
Registered led device: net5big:red:sata4
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 37
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
rtc-rs5c372 0-0032: setting system clock to 2013-11-08 02:14:58 UTC (1383876898)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 0
fvdw2 disk indexfvdw 0
fvdw3 disk indexfvdw 4
fvdw4 disk diskname= sde
sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sde] 4096-byte physical blocks
sd 0:0:0:0: [sde] Write Protect is off
sd 0:0:0:0: [sde] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 1
fvdw2 disk indexfvdw 1
fvdw3 disk indexfvdw 3
fvdw4 disk diskname= sdd
sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sde: sde1
sd 1:0:0:0: [sdd] 4096-byte physical blocks
sd 0:0:0:0: [sde] Attached SCSI disk
sd 1:0:0:0: [sdd] Write Protect is off
sd 1:0:0:0: [sdd] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 2
fvdw2 disk indexfvdw 2
fvdw3 disk indexfvdw 2
fvdw4 disk diskname= sdc
sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdd: sdd1
sd 1:0:0:0: [sdd] Attached SCSI disk
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 3
fvdw2 disk indexfvdw 3
fvdw3 disk indexfvdw 1
fvdw4 disk diskname= sdb
sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 3:0:0:0: [sdb] 4096-byte physical blocks
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 3:0:0:0: [sdb] Attached SCSI disk
sdc: sdc1
sd 2:0:0:0: [sdc] Attached SCSI disk
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5
fvdw1 disk index 4
fvdw2 disk indexfvdw 4
fvdw3 disk indexfvdw 0
fvdw4 disk diskname= sda
sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: [sda] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
EXT3-fs (sda7): recovery required on readonly filesystem
EXT3-fs (sda7): write access will be enabled during recovery
EXT3-fs: barriers not enabled
EXT3-fs (sda7): recovery complete
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:71.
Freeing init memory: 128K
EXT3-fs (sda7): warning: checktime reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k
NTFS driver 2.1.30 [Flags: R/W MODULE].
fuse init (API version 7.16)
usbcore: registered new interface driver usblp
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
iSCSI Enterprise Target Software - version trunk
iscsi_trgt: Registered io type fileio
iscsi_trgt: Registered io type blockio
iscsi_trgt: Registered io type nullio
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
EXT3-fs: barriers not enabled
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
NTFS volume version 3.1.
NTFS-fs error (device sdb1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdc1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sdd1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
NTFS volume version 3.1.
NTFS-fs error (device sde1): load_system_files(): Volume is dirty. Mounting read-only. Run chkdsk and mount in Windows.
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
udevd (820): /proc/820/oom_adj is deprecated, please use /proc/820/oom_score_adj instead.
~ #
You do not have the required permissions to view the files attached to this post.
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Re: lacie 5 big network v.1 please support for fvdw
by taetae » Wed Nov 06, 2013 10:35 am
do you think the fan runs? there is the possibility to test it?
ps after about 15 minutes and two start-eighths, saw their HD is normal for this time we put the Institute for viewing 5 hd?
http://imageshack.us/photo/my-images/41/t3dw.jpg/
ps after about 15 minutes and two start-eighths, saw their HD is normal for this time we put the Institute for viewing 5 hd?
http://imageshack.us/photo/my-images/41/t3dw.jpg/
You do not have the required permissions to view the files attached to this post.
- taetae
- Donator VIP
- Posts: 438
- Joined: Mon Aug 26, 2013 9:02 am
Return to Lacie 5Big Network vs1
Who is online
Users browsing this forum: No registered users and 2 guests