Raid clean, degraded completed, estimated time ...

[razzor0]

dont looking good, i leave hdd 1 in slot 1 as you wrote and trying to start but the led is RED and the program wont starting

is it possible to take data from hdds ?

thank you

[fvdw]

the only option I see if slot 1 is really broken, (maybe Jocko has more ??) is connecting 5 disks to a another pc running linux and assemble the raid array.

mm...strange that you can run the standalone kernel with all 5 disks installed and not with only 1 disk.
To see if the problem is still related to the disk, try to put disk 2 in slot 1 and see if you can run the standalone kernel and see sda now in dmesg.
If that is the case then you couldput in a new disk install fvdw-sl firmware and put the other disks in slot 2-5 and boot the nas and assemble the array etc. Of course your settings will be lost but you should then be able to recover your data.

If that fails also you might try another power supply but its unlikely that that is the problem.

[razzor0]

Yep its look like then only disk is dead.... I was able to start standalone with disk 2 in port 1
here is output. Please tell me I should buy just a new HDD. I need those data badly. Thank you !

Code: Select all

root@fvdw-sta-kirkwood:/ # dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #171 PREEMPT Wed Jan 17 23:33:31 CET 2018
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie 5Big Network v2
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0982898, node_mem_map dfbfb000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 netconsole=6666@169.254.30.252/,6666@169.254.30.243/
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 509780K/524288K available (5950K kernel code, 220K rwdata, 1596K rodata, 1933K init, 233K bss, 14508K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0766b44   (7547 kB)
[    0.000000]       .init : 0xc0767000 - 0xc094a4cc   (1934 kB)
[    0.000000]       .data : 0xc094c000 - 0xc0983100   ( 221 kB)
[    0.000000]        .bss : 0xc098310c - 0xc09bd56c   ( 234 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000011] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[   19.543023] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[   19.632992] pid_max: default: 32768 minimum: 301
[   19.633127] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   19.633146] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   19.633688] CPU: Testing write buffer coherency: ok
[   19.633998] Setting up static identity map for 0x5a6ac0 - 0x5a6b18
[   19.636598] VFP support v0.3: not present
[   19.637132] xor: measuring software checksum speed
[   19.733023]    arm4regs  :  1089.200 MB/sec
[   19.832986]    8regs     :   654.400 MB/sec
[   19.932973]    32regs    :   902.800 MB/sec
[   19.932992] xor: using function: arm4regs (1089.200 MB/sec)
[   19.933008] pinctrl core: initialized pinctrl subsystem
[   19.933126] NET: Registered protocol family 16
[   19.933483] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   19.936187] Kirkwood: MV88F6281-A0, TCLK=166666667.
[   19.936213] Feroceon L2: Enabling L2
[   19.936251] Feroceon L2: Cache support initialised.
[   19.937343] mv_usb_init 1
[   19.937362] mv_usb_init 2 devnum = 0
[   19.937374] init function mv_usb_init finished
[   19.937382] initial MPP regs: 01112222 00003311 33331100 33003333 00000033 00000000 00000000
[   19.937414]   final MPP regs: 01112222 00003311 33331100 33003333 00000033 00000000 00000000
[   19.937600]  orion-ehci registered
[   19.939431] orion_gpio_is_valid: invalid GPIO 7
[   19.939913] Kirkwood PCIe port 0: link down
[   19.939923] Kirkwood PCIe port 1: link up
[   19.939933] PCI: bus0 uses PCIe port 0
[   19.940172] PCI host bridge to bus 0000:00
[   19.940193] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   19.940207] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   19.940220] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   19.940267] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[   19.940297] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[   19.940315] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x1fffffff]
[   19.940365] pci 0000:00:00.0: supports D1 D2
[   19.940639] PCI: bus0: Fast back to back transfers disabled
[   19.940658] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[   19.940670] PCI: bus1 uses PCIe port 1
[   19.940894] PCI host bridge to bus 0000:01
[   19.940912] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[   19.940926] pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
[   19.940939] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[   19.940977] PCI: bus1: Fast back to back transfers enabled
[   19.940991] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   19.965154] bio: create slab <bio-0> at 0
[   20.134157] raid6: int32x1     95 MB/s
[   20.303134] raid6: int32x2    123 MB/s
[   20.473206] raid6: int32x4    120 MB/s
[   20.643074] raid6: int32x8    128 MB/s
[   20.643084] raid6: using algorithm int32x8 (128 MB/s)
[   20.643092] raid6: using intx1 recovery algorithm
[   20.643918] SCSI subsystem initialized
[   20.644373] libata version 3.00 loaded.
[   20.645258] usbcore: registered new interface driver usbfs
[   20.645431] usbcore: registered new interface driver hub
[   20.645626] usbcore: registered new device driver usb
[   20.648105] cfg80211: Calling CRDA to update world regulatory domain
[   20.648352] Switched to clocksource orion_clocksource
[   20.650629] NET: Registered protocol family 2
[   20.651095] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[   20.651154] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[   20.651206] TCP: Hash tables configured (established 4096 bind 4096)
[   20.651259] TCP: reno registered
[   20.651273] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   20.651295] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   20.651486] NET: Registered protocol family 1
[   20.651754] RPC: Registered named UNIX socket transport module.
[   20.651765] RPC: Registered udp transport module.
[   20.651772] RPC: Registered tcp transport module.
[   20.651780] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   20.651801] PCI: CLS 32 bytes, default 32
[   20.798367] NetWinder Floating Point Emulator V0.97 (double precision)
[   20.798492] gpio-usb-probe-4b err=0
[   20.798508] gpio-usb gpio-usb: USB GPIO's initialized
[   20.800103] futex hash table entries: 256 (order: -1, 3072 bytes)
[   20.901776] VFS: Disk quotas dquot_6.5.2
[   20.901826] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   20.902255] NFS: Registering the id_resolver key type
[   20.902304] Key type id_resolver registered
[   20.902314] Key type id_legacy registered
[   20.902331] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   20.902345] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   20.902448] NTFS driver 2.1.30 [Flags: R/W].
[   20.902479] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   20.902626] fuse init (API version 7.22)
[   20.903247] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[   20.903666] msgmni has been set to 995
[   20.904785] async_tx: api initialized (async)
[   20.904971] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   20.904983] io scheduler noop registered
[   20.904991] io scheduler deadline registered
[   20.905011] io scheduler cfq registered (default)
[   20.905391] mv_xor mv_xor.0: Marvell shared XOR driver
[   20.943005] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   20.983002] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   20.983249] mv_xor mv_xor.1: Marvell shared XOR driver
[   21.022999] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   21.063000] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   21.068877] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   21.089992] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   21.714751] console [ttyS0] enabled
[   21.727638] brd: module loaded
[   21.735348] loop: module loaded
[   21.738782] Uniform Multi-Platform E-IDE driver
[   21.743651] ide-gd driver 1.18
[   21.748199] sata_mv sata_mv.0: version 1.28
[   21.748263] sata_mv sata_mv.0: cannot get optional clkdev
[   21.754097] sata_mv sata_mv.0: slots 32 ports 2
[   21.761639] scsi0 : sata_mv
[   21.765157] scsi1 : sata_mv
[   21.768344] ata1: SATA max UDMA/133 irq 21
[   21.772423] ata2: SATA max UDMA/133 irq 21
[   21.779151] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[   21.784193] Creating 2 MTD partitions on "spi_flash":
[   21.789222] 0x000000000000-0x00000007d000 : "u-boot"
[   21.795455] 0x00000007e000-0x00000007f000 : "u-boot-env"
[   21.803551] tun: Universal TUN/TAP device driver, 1.6
[   21.808578] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   21.815060] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   21.823368] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   21.839774] libphy: orion_mdio_bus: probed
[   21.844052] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   22.282973] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   22.302969] ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   22.364616] ata1.00: hard resetting link
[   22.713729] ata1.01: hard resetting link
[   22.957366] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:8f:c2:05
[   23.073727] ata1.02: hard resetting link
[   23.433723] ata1.03: hard resetting link
[   23.993000] ata1.03: ATA-8: ST2000DL001-9VT156, CC41, max UDMA/133
[   23.999151] ata1.03: 3907029168 sectors, multi 0: LBA48
[   24.069128] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:4b:8f:15:8f
[   24.077876] ata1.03: configured for UDMA/133
[   24.082339] ata1: EH complete
[   24.085470] PPP generic driver version 2.4.2
[   24.090048] PPP Deflate Compression module registered
[   24.095142] PPP MPPE Compression module registered
[   24.099907] NET: Registered protocol family 24
[   24.104682] scsi 0:3:0:0: Direct-Access     ATA      ST2000DL001-9VT1 CC41 PQ: 0 ANSI: 5
[   24.113161] usbcore: registered new interface driver rtl8187
[   24.118796] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[   24.126526] fvdw1 disk index before get_sd_name = 0
[   24.131382] device-name= sata_mv
[   24.134747] fvdw2 disk index after get_sd_name = 0
[   24.139512] fvdw3 prefix[0]=s  prefix[1]=d
[   24.143689] usbcore: registered new interface driver pegasus
[   24.149524] usbcore: registered new interface driver asix
[   24.154939] fvdw4 diskname = sda
[   24.158699] usbcore: registered new interface driver ax88179_178a
[   24.164904] sd 0:3:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   24.172616] sd 0:3:0:0: [sda] 4096-byte physical blocks
[   24.178258] sd 0:3:0:0: Attached scsi generic sg0 type 0
[   24.183920] usbcore: registered new interface driver cdc_ether
[   24.190079] usbcore: registered new interface driver net1080
[   24.196000] sd 0:3:0:0: [sda] Write Protect is off
[   24.200776] sd 0:3:0:0: [sda] Mode Sense: 00 3a 00 00
[   24.200988] sd 0:3:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   24.210138] usbcore: registered new interface driver cdc_subset
[   24.216231] usbcore: registered new interface driver zaurus
[   24.222917] usbcore: registered new interface driver ipheth
[   24.228683] usbcore: registered new interface driver cdc_ncm
[   24.235509] aoe: cannot create debugfs directory
[   24.240247] aoe: AoE v85 initialised.
[   24.244826] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   24.250903] i2c /dev entries driver
[   24.255475] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[   24.269323]  sda: sda4 < sda5 sda6 sda7 sda8 >
[   24.276147] sd 0:3:0:0: [sda] Attached SCSI disk
[   24.287239] md: linear personality registered for level -1
[   24.292700] md: raid0 personality registered for level 0
[   24.298081] md: raid1 personality registered for level 1
[   24.303442] md: raid10 personality registered for level 10
[   24.309049] md: raid6 personality registered for level 6
[   24.314374] md: raid5 personality registered for level 5
[   24.319657] md: raid4 personality registered for level 4
[   24.325164] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[   24.333801] device-mapper: multipath: version 1.6.0 loaded
[   24.339262] device-mapper: multipath round-robin: version 1.0.0 loaded
[   24.345797] device-mapper: multipath queue-length: version 0.1.0 loaded
[   24.352377] device-mapper: multipath service-time: version 0.2.0 loaded
[   24.359044] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   24.365133] device-mapper: raid: Loading target version 1.5.2
[   24.375016] ipip: IPv4 over IPv4 tunneling driver
[   24.380459] TCP: cubic registered
[   24.383875] NET: Registered protocol family 10
[   24.389225] sit: IPv6 over IPv4 tunneling driver
[   24.394722] NET: Registered protocol family 17
[   24.399404] NET: Registered protocol family 5
[   24.404016] 8021q: 802.1Q VLAN Support v1.8
[   24.408216] NET: Registered protocol family 37
[   24.412675] Key type dns_resolver registered
[   24.418213] netpoll: netconsole: local port 6666
[   24.422812] netpoll: netconsole: local IPv4 address 169.254.30.252
[   24.429024] netpoll: netconsole: interface 'eth0'
[   24.433740] netpoll: netconsole: remote port 6666
[   24.438424] netpoll: netconsole: remote IPv4 address 169.254.30.243
[   24.444734] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   24.451584] netpoll: netconsole: device eth0 not up yet, forcing it
[   24.692976] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   24.712970] ata2.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   24.774618] ata2.00: hard resetting link
[   25.123726] ata2.01: hard resetting link
[   25.483723] ata2.02: hard resetting link
[   25.572872] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   25.843726] ata2.03: hard resetting link
[   26.193876] ata2: EH complete
[   28.665744] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   28.675565] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   28.685046] console [netcon0] enabled
[   28.688701] netconsole: network logging started
[   28.693874] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   28.700965] rtc-mv rtc-mv: setting system clock to 2024-05-22 06:19:33 UTC (1716358773)
[   28.714690] Freeing unused kernel memory: 1932K (c0767000 - c094a000)
[   29.802896] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   38.881433] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   38.891651] ehci-orion: EHCI orion driver
[   38.895881] orion-ehci orion-ehci.0: EHCI Host Controller
[   38.901303] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   38.909017] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   38.932981] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   38.939028] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   38.945830] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   38.953073] usb usb1: Product: EHCI Host Controller
[   38.957961] usb usb1: Manufacturer: Linux 3.14.2 ehci_hcd
[   38.963382] usb usb1: SerialNumber: orion-ehci.0
[   38.968770] hub 1-0:1.0: USB hub found
[   38.972574] hub 1-0:1.0: 1 port detected
[   38.983067] usbcore: registered new interface driver usb-storage
[   39.292990] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   39.443422] usb 1-1: New USB device found, idVendor=0424, idProduct=2512
[   39.450124] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   39.458057] hub 1-1:1.0: USB hub found
[   39.461902] hub 1-1:1.0: 2 ports detected
[   71.401572] random: nonblocking pool is initialized


[fvdw]

You should buy a 2TB disk (minimal same size in bytes as the other 4 disks) This is important as the raid array needs 5 disk partition from same size. Then put in this new disk in slot 1 and install fvdw-sl firmware using fvdw-sl console. Now the nas will boot but your settings are lost. How to add the other disks an how to assemble the array in this special must be described by Jocko, I have little knowledge of raid. So wait for him to comment how to proceed.

[razzor0]

Will do thank you ! Question about the drives, currently I have st2000dl001. Is this a good option ST2000NT001 ? Thank you !

[fvdw]

Yes that seems to be the same as the others.

Note: I strongly advise to wait for comment of Jocko before puting the other 4 disks in, in order to prevent loss of the array on those disks

[razzor0]

Ok i have to order the new drive first. Which will come probably next week. Then I will install the fvdw-sl firmware using fvdw-sl console. Once I have it i will write again. Thank you !

[razzor0]

Hello!
Amazon did amazing job and new HDD is already here ! I just installed the firmware on new HDD without the other HDDs.
@Jocko could you please support me to rebuild the raid5 ?
Thanks a lot !

[Jocko]

Hi

As the former disk seems to dead, we can not reuse your nas database and the raid is not rebuilt on nas booting.

So I assume you have the new sda disk in its slot and put the other disks in the other slots in the same order; Then start the nas and open a shell window. Use the default credential (root- giveit2me)
Run

Code: Select all

mdadm --assemble -f -R --uuid="30b66c2b:dc82e187:71c77728:dd40f1de"  /dev/md0

and post

Code: Select all

cat /proc/mdstat
cp /etc/mdadm.0 /rw_fs/etc/mdadm.conf
echo "ARRAY /dev/md0 level=raid5 num-devices=5 name=0 UUID=30b66c2b:dc82e187:71c77728:dd40f1de" >> /rw_fs/etc/mdadm.conf
cat /etc/mdadm.conf


Reboot the nas and the raid should be available now. Please to post

Code: Select all

mount

Later we have to add sda8 in the raid to restore the redundancy and then recreate all settings of your shares. But first step is to get your raid volume on nas booting

[razzor0]

Hi Jocko ! Thank you for your support on this !

Code: Select all


root@fvdwsl-base:/ # cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md0 : active raid5 sdb8[1] sde8[4] sdd8[3] sdc8[2]
      7800905728 blocks super 1.0 level 5, 512k chunk, algorithm 2 [5/4] [_UUUU]
      bitmap: 4/15 pages [16KB], 65536KB chunk

unused devices: <none>
root@fvdwsl-base:/ # cp /etc/mdadm.0 /rw_fs/etc/mdadm.conf
root@fvdwsl-base:/ # echo "ARRAY /dev/md0 level=raid5 num-devices=5 name=0 UUID=30b66c2b
root@fvdwsl-base:/ # cat /etc/mdadm.conf
CREATE owner=root group=root mode=0666 auto=yes metadata=1.0
PROGRAM /usr/bin/mdadm-events
DEVICE /dev/sd* /dev/se*

#MAILADDR
ARRAY /dev/md0 level=raid5 num-devices=5 name=0 UUID=30b66c2b:dc82e187:71c77728:dd40f1de
root@fvdwsl-base:/ #

Code: Select all

root@fvdwsl-base:/ # mount
/dev/sda1 on / type ext3 (rw,noatime,data=ordered)
none on /proc type proc (rw,noatime)
none on /sys type sysfs (rw,noatime)
none on /dev/pts type devpts (rw,noatime,mode=600,ptmxmode=000)
/dev/sda5 on /rw_fs type ext3 (rw,noatime,data=ordered)
tmpfs on /rw_fs/tmp/usr/var type tmpfs (rw,noatime,size=5000k)
nfsd on /proc/fs/nfsd type nfsd (rw,noatime)
/dev/sda8 on /share/1000 type ext4 (rw,noatime,nodelalloc,data=ordered)
/dev/sda7 on /lacie-boot type ext3 (rw,noatime,data=ordered)
/dev/sda7 on /lib/firmware type ext3 (rw,noatime,data=ordered)