I'm doing upgrade to the latest version using the web interface
---- not work upgrade interface-----
fvdw-sl firmware version 11-0
is the version of the guide in the manual
KOcrash system random.....
fan
switch led
usb-extras
upgrade firmware
OKTemperature information
----- 2 hdd--- --------1 hd and 32gb pen drive usb--------
Kernel panic will not start ....
- Code: Select all
U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9
U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280
Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 32bit width
[4096kB@ffc00000] Flash: 4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
*** Warning - bad CRC, using default environment
CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net: egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot: 0
Waiting for LUMP (5)
no lump receive; continuing
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 4: OK
Model: WDC WD5000AADS-00S9B0 Firm: 01.00A01 Ser#: WD-WCAV90478832
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
** Device 0 not available
** Device 1 not available
** Device 2 not available
** Device 3 not available
** Device 0 not available
** Device 1 not available
** Device 2 not available
** Device 3 not available
Loading from IDE device 4, partition 6: Name: hde6
Type: U-Boot
Image Name: Linux-2.6.39.4
Created: 2013-08-28 21:39:43 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1864076 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-2.6.39.4
Created: 2013-08-28 21:39:43 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1864076 Bytes = 1.8 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.5.4 (GCC) ) #8 PREEMPT Wed Aug 28 22:39:19 GMT+1 2013
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 126000k/126000k available, 5072k reserved, 0K highmem
Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff1000 ( 4 kB)
fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
vmalloc : 0xc8800000 - 0xfd800000 ( 848 MB)
lowmem : 0xc0000000 - 0xc8000000 ( 128 MB)
modules : 0xbf000000 - 0xc0000000 ( 16 MB)
.init : 0xc0008000 - 0xc0028000 ( 128 kB)
.text : 0xc0028000 - 0xc03a3000 (3564 kB)
.data : 0xc03a4000 - 0xc03bf9e0 ( 111 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
RCU-based detection of stalled CPUs is disabled.
Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
net5big: powering up SATA drives
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff])
pci 0000:01:07.0: BAR 2: assigned [io 0x100000-0x1000ff]
pci 0000:01:07.0: BAR 2: set to [io 0x100000-0x1000ff] (PCI address [0x100000-0x1000ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv 0000:01:07.0: version 1.28
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:8b:60:2b
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
mv_xor mv_xor.1: Self-test copy failed compare, disabling
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
ata1: SATA link down (SStatus 0 SControl 300)
NET: Registered protocol family 37
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
rtc-rs5c372 0-0032: setting system clock to 2013-09-18 18:11:19 UTC (1379527879)
usb 1-1: new high speed USB device number 2 using orion-ehci
scsi13 : usb-storage 1-1:1.0
ata2: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata4: SATA link down (SStatus 0 SControl 300)
scsi 13:0:0:0: Direct-Access TDK LoR TF10 PMAP PQ: 0 ANSI: 4
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5
sd 4:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sdb] Write Protect is off
sd 4:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 4:0:0:0: [sdb] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
sd 13:0:0:0: [sda] 62529536 512-byte logical blocks: (32.0 GB/29.8 GiB)
sd 13:0:0:0: [sda] Write Protect is off
sd 13:0:0:0: [sda] Assuming drive cache: write through
sd 13:0:0:0: [sda] Assuming drive cache: write through
sda: sda1
sd 13:0:0:0: [sda] Assuming drive cache: write through
sd 13:0:0:0: [sda] Attached SCSI removable disk
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
VFS: Cannot open root device "sda7" or unknown-block(8,7)
Please append a correct "root=" boot option; here are the available partitions:
0810 488386584 sdb driver: sd
0811 513056 sdb1 00000000-0000-0000-0000-000000000000sdb1
0812 514080 sdb2 00000000-0000-0000-0000-000000000000sdb2
0813 514080 sdb3 00000000-0000-0000-0000-000000000000sdb3
0814 1 sdb4 00000000-0000-0000-0000-000000000000sdb4
0815 802226 sdb5 00000000-0000-0000-0000-000000000000sdb5
0816 7008 sdb6 00000000-0000-0000-0000-000000000000sdb6
0817 513056 sdb7 00000000-0000-0000-0000-000000000000sdb7
0818 485515406 sdb8 00000000-0000-0000-0000-000000000000sdb8
0800 31264768 sda driver: sd
0801 31260736 sda1 00000000-0000-0000-0000-000000000000sda1
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(8,7)
Backtrace:
[<c0035f14>] (dump_backtrace+0x0/0x114) from [<c02d0124>] (dump_stack+0x18/0x1c)
r6:00008001 r5:c780a000 r4:c03bfde8 r3:00000002
[<c02d010c>] (dump_stack+0x0/0x1c) from [<c02d019c>] (panic+0x74/0x19c)
[<c02d0128>] (panic+0x0/0x19c) from [<c0008de8>] (mount_block_root+0x240/0x290)
r3:c7820000 r2:00000000 r1:c7821f60 r0:c035b651
r7:c0022a30
[<c0008ba8>] (mount_block_root+0x0/0x290) from [<c0008e8c>] (mount_root+0x54/0x6c)
[<c0008e38>] (mount_root+0x0/0x6c) from [<c0008fcc>] (prepare_namespace+0x128/0x17c)
r5:c0022a45 r4:c03bfa80
[<c0008ea4>] (prepare_namespace+0x0/0x17c) from [<c0008a14>] (kernel_init+0x108/0x144)
r5:c0022218 r4:c03bfa20
[<c000890c>] (kernel_init+0x0/0x144) from [<c00473ac>] (do_exit+0x0/0x71c)
r5:c000890c r4:00000000