plugout.net

by **taetae** » Tue Dec 31, 2013 10:17 am

ok I'll wait here;-)

by **fvdw** » Tue Dec 31, 2013 11:03 am

I do not have a reply yet but found a similar issue on the internet and i patched the xor driver

maybe you can try if this ones goes ok (see pm)

by **taetae** » Tue Dec 31, 2013 11:18 am

:punk :punk :punk :punk :punk :woohoo :woohoo :woohoo :woohoo :woohoo
we succeeded
u-boot console

Code: Select all: provided by fvdw waiting for u-boot.. starting u-boot net console click on window and press enter Marvell>> setenv ipaddr ${ipaddr}; setenv serverip ${serverip}; setenv bootargs console=ttyS0,115200 netconsole=6666@${ipaddr}/,6666@${serverip}/ root=/dev/sda7 earlyprintk setenv ipaddr ${ipaddr}; setenv serverip ${serverip}; setenv bootargs console=tt yS0,115200 netconsole=6666@${ipaddr}/,6666@${serverip}/ root=/dev/sda7 earlyprin tk Marvell>> tftpboot 0x800000 UIMAGE-395-5BIG1-22 tftpboot 0x800000 UIMAGE-395-5BIG1-22 Using egiga0 device TFTP from server 192.168.1.29; our IP address is 192.168.1.252 Filename 'UIMAGE-395-5BIG1-22'. Load address: 0x800000 Loading: ################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ########################################### done Bytes transferred = 1879232 (1cacc0 hex) Marvell>> bootm bootm ## Booting image at 00800000 ... Image Name: Linux-3.9.5 Created: 2013-12-31 10:56:08 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1879168 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Booting Linux on physical CPU 0x0 Linux version 3.9.5 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #22 Tue Dec 31 11:55:40 GMT+1 2013 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: LaCie 5Big1 Network Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@19 2.168.1.29/ root=/dev/sda7 earlyprintk PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) __ex_table already sorted, skipping sort Memory: 128MB = 128MB total Memory: 125964k/125964k available, 5108k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0363fdc (3440 kB) .init : 0xc0364000 - 0xc0383094 ( 125 kB) .data : 0xc0384000 - 0xc03aacc0 ( 156 kB) .bss : 0xc03aacc0 - 0xc03d973c ( 187 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:64 sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms Console: colour dummy device 80x30 Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 Setting up static identity map for 0xc029b120 - 0xc029b15c Orion: Applying 5281 D0 WFI workaround. 5big1 init 5 5big1 init 11 5big1 init end pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff] PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized NET: Registered protocol family 2 UDP hash table entries: 256 (order: 0, 4096 bytes) Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Register Driver 'mv_xor' serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A Register Driver 'at24' ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52 ata10: SATA max UDMA/133 irq 29 ata11: SATA max UDMA/133 irq 29 ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu> mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 Register Driver 'rtc-ds1374' g762 probe 1 Register Driver 'gpio-fan' Register Driver 'mv_crypto' NET: Registered protocol family 17 netpoll: netconsole: remote IPv4 address 192.168.1.29 ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw3 prefix[0]=s prefix[1]=d sd 0:0:0:0: [sde] 4096-byte physical blocks ata9: failed to resume link (SControl 0) fvdw2 disk index after get_sd_name = 3 sd 1:0:0:0: [sdd] Write Protect is off ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdd] Attached SCSI disk console [netcon0] enabled netconsole: network logging started drivers/rtc/hctosys.c: unable to open rtc device (rtc0) ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 3 device-name= sata_mv fvdw2 disk index after get_sd_name = 1 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdb sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 3:0:0:0: [sdb] 4096-byte physical blocks sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc4 < sdc5 sdc6 sdc7 sdc8 > sd 2:0:0:0: [sdc] Attached SCSI disk ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) sdb: sdb4 < sdb5 sdb6 sdb7 sdb8 > sd 3:0:0:0: [sdb] Attached SCSI disk ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133 ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 4 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sda sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk ata6: SATA link down (SStatus 0 SControl 300) ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) ata10: failed to resume link (SControl 0) ata10: SATA link down (SStatus 0 SControl 0) ata11: failed to resume link (SControl 0) ata11: SATA link down (SStatus 0 SControl 0) ata12: failed to resume link (SControl 0) ata12: SATA link down (SStatus 0 SControl 0) ata13: failed to resume link (SControl 0) ata13: SATA link down (SStatus 0 SControl 0) kjournald starting. Commit interval 5 seconds EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sda7): using internal journal EXT3-fs (sda7): recovery complete EXT3-fs (sda7): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 8:71. Freeing init memory: 124K kjournald starting. Commit interval 5 seconds EXT3-fs (sda5): using internal journal EXT3-fs (sda5): recovery complete EXT3-fs (sda5): mounted filesystem with ordered data mode Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k cifs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_ unload ARMv5 ' isofs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod _unload ARMv5 ' ntfs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_ unload ARMv5 ' fuse: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_ unload ARMv5 ' usblp: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod _unload ARMv5 ' nfs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_u nload ARMv5 ' nfsd: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_ unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' v4l2_int_device: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' v4l2_common: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9 .5 mod_unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' uvcvideo: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' kjournald starting. Commit interval 5 seconds EXT3-fs (sda8): using internal journal EXT3-fs (sda8): recovery complete EXT3-fs (sda8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdb8): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sdb8): using internal journal EXT3-fs (sdb8): recovery complete EXT3-fs (sdb8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdc8): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sdc8): using internal journal EXT3-fs (sdc8): recovery complete EXT3-fs (sdc8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdd8): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sdd8): using internal journal EXT3-fs (sdd8): recovery complete EXT3-fs (sdd8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sde8): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sde8): using internal journal EXT3-fs (sde8): recovery complete EXT3-fs (sde8): mounted filesystem with ordered data mode udevd (884): /proc/884/oom_adj is deprecated, please use /proc/884/oom_score_adj instead.

Seriale Console

Code: Select all: 0 Marvell>> boot Waiting for LUMP (5) Lump received switching to NetConsole on 192.168.1.29 Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.9.5 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #22 Tue Dec 31 11:55:40 GMT+1 2013 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: LaCie 5Big1 Network Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 bootconsole [earlycon0] enabled Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.29/ root=/dev/sda7 earlyprintk PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) __ex_table already sorted, skipping sort Memory: 128MB = 128MB total Memory: 125964k/125964k available, 5108k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0363fdc (3440 kB) .init : 0xc0364000 - 0xc0383094 ( 125 kB) .data : 0xc0384000 - 0xc03aacc0 ( 156 kB) .bss : 0xc03aacc0 - 0xc03d973c ( 187 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:64 sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms Console: colour dummy device 80x30 Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc029b120 - 0xc029b15c NET: Registered protocol family 16 DMA: preallocated 1024 KiB pool for atomic coherent allocations Register Driver 'dummy' 5big1 init started Orion ID: MV88F5281-D0. TCLK=166666667. Orion: Applying 5281 D0 WFI workaround. 5big1 init 1 5big1 init 2 net5big: powering up SATA drives 5big1 init 3 5big1 init 4 5big1 init 5 5big1 init 6 5big1 init 7 5big1 init 8 5big1 init 9 5big1 init 10 5big1 init 11 5big1 init 12 net5big: turning off power-off control GPIO net5big: Flash writing is not yet supported. 5big1 init end net5big_pci_preinit failed to gpio_request 20 PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] PCI: bus0: Fast back to back transfers disabled PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff] pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] PCI: bus1: Fast back to back transfers enabled pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit] pci 0000:01:07.0: BAR 2: assigned [io 0x10000-0x100ff] bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized Register Driver 'Generic PHY' Register Driver 'usbfs' usbcore: registered new interface driver usbfs Register Driver 'hub' usbcore: registered new interface driver hub Register Driver 'usb' usbcore: registered new device driver usb Register Driver 'i2c-gpio' Switching to clocksource orion_clocksource NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Register Driver 'alarmtimer' VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 246 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Register Driver 'mv_xor' mv_xor mv_xor.0: Marvell shared XOR driver mv_xor mv_xor.0: Self-test copy failed compare, disabling Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Register Driver 'serial8250' serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled, bootconsole disabled console [ttyS0] enabled, bootconsole disabled Register Driver 'serial' brd: module loaded loop: module loaded Register Driver 'at24' Register Driver 'eeprom' Register Driver 'sd' Register Driver 'ahci' Register Driver 'sata_mv' sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv scsi4 : sata_mv scsi5 : sata_mv scsi6 : sata_mv scsi7 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52 ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52 ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52 ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52 ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52 ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52 ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52 ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52 Register Driver 'sata_mv' sata_mv sata_mv.0: cannot get optional clkdev sata_mv sata_mv.0: slots 32 ports 5 scsi8 : sata_mv scsi9 : sata_mv scsi10 : sata_mv scsi11 : sata_mv scsi12 : sata_mv ata9: SATA max UDMA/133 irq 29 ata10: SATA max UDMA/133 irq 29 ata11: SATA max UDMA/133 irq 29 ata12: SATA max UDMA/133 irq 29 ata13: SATA max UDMA/133 irq 29 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu> ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu> Register Driver 'mv643xx_eth' mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 libphy: mv643xx_eth smi: probed Register Driver 'mv643xx_eth_port' mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:8b:60:2b mousedev: PS/2 mouse device common for all mice Register Driver 'rtc-ds1307' Register Driver 'rtc-ds1374' i2c /dev entries driver Register Driver 'mv64xxx_i2c' at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write Register Driver 'g762' g762 probe started g762 probe 1 g762 probe 2 g762 probe 3 g762 probe 4 g762 probe 5 g762 probe 6 g762 probe 7 Register Driver 'gpio-fan' Register Driver 'lm75' Register Driver 'lm77' Register Driver 'leds-gpio' Register Driver 'mv_crypto' Netfilter messages via NETLINK v0.30. IPv4 over IPv4 tunneling driver TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 5 VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0 netpoll: netconsole: local port 6666 netpoll: netconsole: local IPv4 address 192.168.1.252 netpoll: netconsole: interface 'eth0' netpoll: netconsole: remote port 6666 netpoll: netconsole: remote IPv4 address 192.168.1.29 netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff netpoll: netconsole: device eth0 not up yet, forcing it ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 0 device-name= sata_mv fvdw2 disk index after get_sd_name = 4 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sde sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sde] 4096-byte physical blocks sd 0:0:0:0: [sde] Write Protect is off sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata9: failed to resume link (SControl 0) ata9: SATA link down (SStatus 0 SControl 0) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 1 device-name= sata_mv fvdw2 disk index after get_sd_name = 3 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdd sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdd] 4096-byte physical blocks sd 1:0:0:0: [sdd] Write Protect is off sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde4 < sde5 sde6 sde7 sde8 > sd 0:0:0:0: [sde] Attached SCSI disk ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 2 device-name= sata_mv fvdw2 disk index after get_sd_name = 2 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdc sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 2:0:0:0: [sdc] 4096-byte physical blocks sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd4 < sdd5 sdd6 sdd7 sdd8 > sd 1:0:0:0: [sdd] Attached SCSI disk mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled console [netcon0] enabled netconsole: network logging started drivers/rtc/hctosys.c: unable to open rtc device (rtc0) ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 3 device-name= sata_mv fvdw2 disk index after get_sd_name = 1 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdb sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 3:0:0:0: [sdb] 4096-byte physical blocks sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc4 < sdc5 sdc6 sdc7 sdc8 > sd 2:0:0:0: [sdc] Attached SCSI disk ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) sdb: sdb4 < sdb5 sdb6 sdb7 sdb8 > sd 3:0:0:0: [sdb] Attached SCSI disk ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133 ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 4 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sda sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk ata6: SATA link down (SStatus 0 SControl 300) ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) ata10: failed to resume link (SControl 0) ata10: SATA link down (SStatus 0 SControl 0) ata11: failed to resume link (SControl 0) ata11: SATA link down (SStatus 0 SControl 0) ata12: failed to resume link (SControl 0) ata12: SATA link down (SStatus 0 SControl 0) ata13: failed to resume link (SControl 0) ata13: SATA link down (SStatus 0 SControl 0) kjournald starting. Commit interval 5 seconds EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sda7): using internal journal EXT3-fs (sda7): recovery complete EXT3-fs (sda7): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) on device 8:71. Freeing init memory: 124K start rcS set global environment params mount proc remount root file system rw mount sysfs start boot log detect and set platform 5big1 update dev nodes booting using root file system... make dev node for buttons... mkdir: can't create directory '/dev/input': File exists mknod: /dev/input/event0: File exists make dev node for tun device... mknod: /dev/net/tun: File exists enable IP forwarding... start buttons control daemon Wed Nov 16 12:00:00 GMT+1 2011 create temporary passwd file run udevstart to update dev nodes when necessary mkdir: can't create directory 'rw_fs': File exists kjournald starting. Commit interval 5 seconds EXT3-fs (sda5): using internal journal EXT3-fs (sda5): recovery complete EXT3-fs (sda5): mounted filesystem with ordered data mode Setting up swapspace version 1, size = 526413824 bytes UUID=864df4e7-7590-49a4-b827-2f8ce97dca68 Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k inserting kernel modules: cifs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' isofs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' ntfs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' fuse: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' usblp: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' nfs: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' nfsd: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' v4l2_int_device: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' v4l2_common: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' videodev: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' uvcvideo: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' Usage: mount -V : print version mount -h : print this help mount : list mounted filesystems mount -l : idem, including volume labels So far the informational part. Next the mounting. The command is `mount [-t fstype] something somewhere'. Details found in /etc/fstab may be omitted. mount -a [-t|-O] ... : mount all stuff from /etc/fstab mount device : mount device at the known place mount directory : mount known device here mount -t type dev dir : ordinary mount command Note that one does not really mount a device, one mounts a filesystem (of the given type) found on the device. One can also mount an already visible directory tree elsewhere: mount --bind olddir newdir or move a subtree: mount --move olddir newdir One can change the type of mount containing the directory dir: mount --make-shared dir mount --make-slave dir mount --make-private dir mount --make-unbindable dir One can change the type of all the mounts in a mount subtree containing the directory dir: mount --make-rshared dir mount --make-rslave dir mount --make-rprivate dir mount --make-runbindable dir A device can be given by name, say /dev/hda1 or /dev/cdrom, or by label, using -L label or by uuid, using -U uuid . Other options: [-nfFrsvw] [-o options] [-p passwdfd]. For many more details, say man 8 mount . configure loopback network interface setting reboot and standby starting php based setup routines step 1 sudo: /usr/sbin/lsscsi: command not found sudo: /usr/sbin/lsscsi: command not found kjournald starting. Commit interval 5 seconds EXT3-fs (sda8): using internal journal EXT3-fs (sda8): recovery complete EXT3-fs (sda8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdb8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdb8): using internal journal EXT3-fs (sdb8): recovery complete EXT3-fs (sdb8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdc8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdc8): using internal journal EXT3-fs (sdc8): recovery complete EXT3-fs (sdc8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdd8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdd8): using internal journal EXT3-fs (sdd8): recovery complete EXT3-fs (sdd8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sde8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sde8): using internal journal EXT3-fs (sde8): recovery complete EXT3-fs (sde8): mounted filesystem with ordered data mode udevd (884): /proc/884/oom_adj is deprecated, please use /proc/884/oom_score_adj instead. passwd[912]: password for `carmine' changed by user `root' passwd[917]: password for `adelina' changed by user `root' passwd[921]: password for `lucio' changed by user `root' passwd[925]: password for `veronica' changed by user `root' start portmap service starting php based setup routines step2 starting php based setup routines step3 starting php based setup routines step banner php based setup routines finished web permission on resolv.conf set device tuning for dms performance ------------------------ rcS finished ------------------------ list boot.log file start boot log detect and set platform 5big1 UIMAGE-26394-5BIG1-20 5big1 update dev nodes booting using root file system... make dev node for buttons... make dev node for tun device... enable IP forwarding... start buttons control daemon device = 5big1 source = buttons-nwsp2 buttons-nwsp2 daemon started initializing date Wed Nov 16 12:00:00 GMT+1 2011 create temporary passwd file run udevstart to update dev nodes when necessary inserting kernel modules: modprobe: 'cifs.ko': invalid module format modprobe: 'isofs.ko': invalid module format modprobe: 'ntfs.ko': invalid module format modprobe: 'fuse.ko': invalid module format modprobe: 'usblp.ko': invalid module format modprobe: module 'sunrpc' not found modprobe: module 'lockd' not found modprobe: 'nfs.ko': invalid module format modprobe: module 'sunrpc' not found modprobe: module 'lockd' not found modprobe: module 'exportfs' not found modprobe: 'nfsd.ko': invalid module format modprobe: module 'iscsi_trgt' not found modprobe: module 'iscsi_tcp' not found modprobe: 'videodev.ko': invalid module format modprobe: 'v4l2-int-device.ko': invalid module format modprobe: 'videodev.ko': invalid module format modprobe: 'v4l2-common.ko': invalid module format modprobe: 'videodev.ko': invalid module format modprobe: module 'videobuf2_core' not found modprobe: module 'input_core' not found modprobe: module 'videobuf2_vmalloc' not found modprobe: 'uvcvideo.ko': invalid module format configure loopback netwerk interface setting reboot and standby 5big1 rebootd-isp1 5big1 standbyd-isp1 starting php based setup routines step 1 * Found XML database configuration file... [ OK ] * Configuring Disks... [ OK ] * Starting mount of volumes... - Mounting volume Vol-a: [ OK ] - Mounting volume Vol-b: [ OK ] - Mounting volume Vol-c: [ OK ] - Mounting volume Vol-d: [ OK ] - Mounting volume Vol-e: [ OK ] * Finishing mount of volumes... [ OK ] * Generating Hosts File... [ OK ] * Configuring System Hostname... [ OK ] * Configuring Samba... [ OK ] * Configuring LAN interface... [ OK ] * Starting udevd... [ OK ] * Starting web server... [ OK ] * Initializing Timezone... [ OK ] * Configuring Samba... [ OK ] * Configuring System Users... Root password: use default password Set users, linux and samba accounts [ OK ] * Starting syncawayd... [ OK ] * Starting Fvdw-sl Discovery Daemon... [ OK ] start portmap service starting php based setup routines step 2 * Starting dropbear... [ OK ] * Kill temporary dropbear... [ OK ] starting php based setup routines step 3 * Starting daemon update Hosts File... [ OK ] * Starting Disk Temperature Guard... [ OK ] starting php based setup routines step banner *** fvdw-sl NAS firmware This is fvdw-sl version: fvdw-sl 15.0 built on: September 30 2013 LAN IP address: 192.168.1.71 (static) Port configuration: LAN -> eth0 php based setup routines finished web permission on resolv.conf set device tuning for dms performance rcS finished /bin/sh: can't access tty; job control turned off ~ #

by **fvdw** » Tue Dec 31, 2013 11:50 am

finally

it seems that mv_or driver is disabled now, don't know if that is a problem. I also need to recompile the moudles, now samba and so will not work as the cifs module is not loaded.

This will not be this afternoon as I need to go out with the family. But maybe end of the afternoon I still have some time

ps are the g762 drivers inputs visible in /sys ?

by **taetae** » Tue Dec 31, 2013 12:00 pm

Are you comfortable are special days of celebration .....

In this moment of pause I wish you a good start of the year, ttutta to you and your family from the bottom of my heart.

Of course, best wishes are also aimed at Jocko :applause :applause

Code: Select all: /sys # ls block class devices fs module bus dev firmware kernel power /sys #

Code: Select all: /sys # cd dev dev/ devices/ /sys # cd devices/ /sys/devices # ls pci0000:00 pci0000:01 platform system virtual /sys/devices # cd p pci0000:00/ pci0000:01/ platform/ /sys/devices # cd platform/ /sys/devices/platform # ls alarmtimer mv643xx_eth_port.0 orion_wdt serial8250 gpio-keys mv64xxx_i2c.0 physmap-flash.0 serial8250.0 leds-gpio mv_xor.0 power uevent mv643xx_eth.0 orion-ehci.0 sata_mv.0 /sys/devices/platform # cd mv mv643xx_eth.0/ mv64xxx_i2c.0/ mv643xx_eth_port.0/ mv_xor.0/ /sys/devices/platform # cd mv64xxx_i2c.0/ /sys/devices/platform/mv64xxx_i2c.0 # ls driver i2c-0 modalias power subsystem uevent /sys/devices/platform/mv64xxx_i2c.0 # cd i2c-0/ /sys/devices/platform/mv64xxx_i2c.0/i2c-0 # ls 0-0032 0-0051 delete_device name subsystem 0-003e 0-0052 device new_device uevent 0-0050 0-0053 i2c-dev power /sys/devices/platform/mv64xxx_i2c.0/i2c-0 # cd 0-003e /sys/devices/platform/mv64xxx_i2c.0/i2c-0/0-003e # ls driver fan1_fault fan1_target name pwm1_enable uevent fan1_alarm fan1_input hwmon power pwm1_mode fan1_div fan1_pulses modalias pwm1 subsystem /sys/devices/platform/mv64xxx_i2c.0/i2c-0/0-003e #

by **fvdw** » Tue Dec 31, 2013 6:54 pm

Also the best wishes for the new year for you and your family taetae

As old year bonus I just have sent you a pm with the updated kernel modules for 3.9.5 kernel

by **taetae** » Tue Dec 31, 2013 8:41 pm

Code: Select all: __ __ _ _ | \/ | __ _ _ ____ _____| | | | |\/| |/ _` | '__\ \ / / _ \ | | | | | | (_| | | \ V / __/ | | |_| |_|\__,_|_| \_/ \___|_|_| _ _ ____ _ | | | | | __ ) ___ ___ | |_ | | | |___| _ \ / _ \ / _ \| __| | |_| |___| |_) | (_) | (_) | |_ \___/ |____/ \___/ \___/ \__| ** LOADER ** ** MARVELL BOARD: RD-88F5281-LaCie LE U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9 U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280 Soc: 88F5281 D0 (DDR2) CPU running @ 500Mhz SysClock = 166Mhz , TClock = 166Mhz DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB 32bit width [4096kB@ffc00000] Flash: 4 MB Addresses 4M - 0M are saved for the U-Boot usage. Mem malloc Initialization (4M - 3M): Done *** Warning - bad CRC, using default environment CPU : ARM926 (Rev 0) Streaming disabled VFP initialized to Run Fast Mode. USB 0: host mode PCI 0: PCI Express Root Complex Interface PCI 1: PCI-X, speed = 66000000 CPU: Write allocate Disabled Net: egiga0 [PRIME] POWER ON Hit any key to stop autoboot: 28 0 Waiting for LUMP (5) no lump receive; continuing Reset IDE: Marvell Serial ATA Adapter Found adapter at bus 1, device 7 ... Scanning channels Error - Failed initializing(SRST) drive on channel 0 Failed initializing storage deivce connected to SATA channel 0 Device 1: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC 4M0410979 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 2: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC 4M0424246 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 3: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC 4M0219436 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 4: OK Model: WDC WD5000AADS-00S9B0 Firm: 01.00A01 Ser#: WD-WCA V90478832 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) ** Device 0 not available ** Device 0 not available Loading from IDE device 1, partition 6: Name: hdb6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 2, partition 6: Name: hdc6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 3, partition 6: Name: hdd6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 4, partition 6: Name: hde6 Type: U-Boot Image Name: Linux-3.9.5 Created: 2013-12-31 10:56:08 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1879168 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00400000 ... Image Name: Linux-3.9.5 Created: 2013-12-31 10:56:08 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1879168 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.9.5 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #22 Tue Dec 31 11:55:40 GMT+1 2013 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: LaCie 5Big1 Network Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) __ex_table already sorted, skipping sort Memory: 128MB = 128MB total Memory: 125964k/125964k available, 5108k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0363fdc (3440 kB) .init : 0xc0364000 - 0xc0383094 ( 125 kB) .data : 0xc0384000 - 0xc03aacc0 ( 156 kB) .bss : 0xc03aacc0 - 0xc03d973c ( 187 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:64 sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms Console: colour dummy device 80x30 Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc029b120 - 0xc029b15c NET: Registered protocol family 16 DMA: preallocated 1024 KiB pool for atomic coherent allocations Register Driver 'dummy' 5big1 init started Orion ID: MV88F5281-D0. TCLK=166666667. Orion: Applying 5281 D0 WFI workaround. 5big1 init 1 5big1 init 2 net5big: powering up SATA drives 5big1 init 3 5big1 init 4 5big1 init 5 5big1 init 6 5big1 init 7 5big1 init 8 5big1 init 9 5big1 init 10 5big1 init 11 5big1 init 12 net5big: turning off power-off control GPIO net5big: Flash writing is not yet supported. 5big1 init end net5big_pci_preinit failed to gpio_request 20 PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] PCI: bus0: Fast back to back transfers disabled PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff] pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] PCI: bus1: Fast back to back transfers enabled pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit] pci 0000:01:07.0: BAR 2: assigned [io 0x10000-0x100ff] bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized Register Driver 'Generic PHY' Register Driver 'usbfs' usbcore: registered new interface driver usbfs Register Driver 'hub' usbcore: registered new interface driver hub Register Driver 'usb' usbcore: registered new device driver usb Register Driver 'i2c-gpio' Switching to clocksource orion_clocksource NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Register Driver 'alarmtimer' VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 246 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Register Driver 'mv_xor' mv_xor mv_xor.0: Marvell shared XOR driver mv_xor mv_xor.0: Self-test copy failed compare, disabling Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Register Driver 'serial8250' serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled Register Driver 'serial' brd: module loaded loop: module loaded Register Driver 'at24' Register Driver 'eeprom' Register Driver 'sd' Register Driver 'ahci' Register Driver 'sata_mv' sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv scsi4 : sata_mv scsi5 : sata_mv scsi6 : sata_mv scsi7 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52 ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52 ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52 ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52 ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52 ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52 ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52 ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52 Register Driver 'sata_mv' sata_mv sata_mv.0: cannot get optional clkdev sata_mv sata_mv.0: slots 32 ports 5 scsi8 : sata_mv scsi9 : sata_mv scsi10 : sata_mv scsi11 : sata_mv scsi12 : sata_mv ata9: SATA max UDMA/133 irq 29 ata10: SATA max UDMA/133 irq 29 ata11: SATA max UDMA/133 irq 29 ata12: SATA max UDMA/133 irq 29 ata13: SATA max UDMA/133 irq 29 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu> ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn. edu> Register Driver 'mv643xx_eth' mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 libphy: mv643xx_eth smi: probed Register Driver 'mv643xx_eth_port' mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:8b:60 :2b mousedev: PS/2 mouse device common for all mice Register Driver 'rtc-ds1307' Register Driver 'rtc-ds1374' i2c /dev entries driver Register Driver 'mv64xxx_i2c' at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write Register Driver 'g762' g762 probe started g762 probe 1 g762 probe 2 g762 probe 3 g762 probe 4 g762 probe 5 g762 probe 6 g762 probe 7 Register Driver 'gpio-fan' Register Driver 'lm75' Register Driver 'lm77' Register Driver 'leds-gpio' Register Driver 'mv_crypto' Netfilter messages via NETLINK v0.30. IPv4 over IPv4 tunneling driver TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 5 VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0 console [netcon0] enabled netconsole: network logging started drivers/rtc/hctosys.c: unable to open rtc device (rtc0) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 0 device-name= sata_mv fvdw2 disk index after get_sd_name = 4 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sde sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sde] 4096-byte physical blocks sd 0:0:0:0: [sde] Write Protect is off sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata9: failed to resume link (SControl 0) ata9: SATA link down (SStatus 0 SControl 0) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 1 device-name= sata_mv fvdw2 disk index after get_sd_name = 3 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdd sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdd] 4096-byte physical blocks sd 1:0:0:0: [sdd] Write Protect is off sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde4 < sde5 sde6 sde7 sde8 > sd 0:0:0:0: [sde] Attached SCSI disk sdd: sdd4 < sdd5 sdd6 sdd7 sdd8 > sd 1:0:0:0: [sdd] Attached SCSI disk ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 2 device-name= sata_mv fvdw2 disk index after get_sd_name = 2 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdc sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 2:0:0:0: [sdc] 4096-byte physical blocks sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc4 < sdc5 sdc6 sdc7 sdc8 > sd 2:0:0:0: [sdc] Attached SCSI disk ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 3 device-name= sata_mv fvdw2 disk index after get_sd_name = 1 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdb sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 3:0:0:0: [sdb] 4096-byte physical blocks sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb4 < sdb5 sdb6 sdb7 sdb8 > sd 3:0:0:0: [sdb] Attached SCSI disk ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133 ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 4 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sda sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk ata6: SATA link down (SStatus 0 SControl 300) ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) ata10: failed to resume link (SControl 0) ata10: SATA link down (SStatus 0 SControl 0) ata11: failed to resume link (SControl 0) ata11: SATA link down (SStatus 0 SControl 0) ata12: failed to resume link (SControl 0) ata12: SATA link down (SStatus 0 SControl 0) ata13: failed to resume link (SControl 0) ata13: SATA link down (SStatus 0 SControl 0) kjournald starting. Commit interval 5 seconds EXT3-fs (sda7): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 8:71. Freeing init memory: 124K start rcS set global environment params mount proc remount root file system rw EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommen ded EXT3-fs (sda7): using internal journal mount sysfs start boot log detect and set platform 5big1 update dev nodes booting using root file system... make dev node for buttons... mkdir: can't create directory '/dev/input': File exists mknod: /dev/input/event0: File exists make dev node for tun device... mknod: /dev/net/tun: File exists enable IP forwarding... start buttons control daemon Wed Nov 16 12:00:00 GMT+1 2011 create temporary passwd file run udevstart to update dev nodes when necessary mkdir: can't create directory 'rw_fs': File exists kjournald starting. Commit interval 5 seconds EXT3-fs (sda5): using internal journal EXT3-fs (sda5): recovery complete EXT3-fs (sda5): mounted filesystem with ordered data mode Setting up swapspace version 1, size = 526413824 bytes UUID=4eaa514e-d6d2-4279-88af-242b66279e97 Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k inserting kernel modules: NTFS driver 2.1.30 [Flags: R/W MODULE]. fuse init (API version 7.21) Register Driver 'usblp' usbcore: registered new interface driver usblp RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). iscsi_tcp: Unknown symbol iscsi_tcp_segment_done (err 0) iscsi_tcp: Unknown symbol iscsi_session_recovery_timedout (err 0) iscsi_tcp: Unknown symbol iscsi_segment_seek_sg (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_segment_unmap (err 0) iscsi_tcp: Unknown symbol iscsi_target_alloc (err 0) iscsi_tcp: Unknown symbol iscsi_conn_bind (err 0) iscsi_tcp: Unknown symbol iscsi_host_get_param (err 0) iscsi_tcp: Unknown symbol iscsi_session_setup (err 0) iscsi_tcp: Unknown symbol iscsi_eh_abort (err 0) iscsi_tcp: Unknown symbol iscsi_conn_failure (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_hdr_recv_prep (err 0) iscsi_tcp: Unknown symbol iscsi_conn_queue_work (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_cleanup_task (err 0) iscsi_tcp: Unknown symbol iscsi_eh_device_reset (err 0) iscsi_tcp: Unknown symbol iscsi_register_transport (err 0) iscsi_tcp: Unknown symbol iscsi_set_param (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_conn_setup (err 0) iscsi_tcp: Unknown symbol iscsi_conn_get_param (err 0) iscsi_tcp: Unknown symbol iscsi_suspend_tx (err 0) iscsi_tcp: Unknown symbol iscsi_host_free (err 0) iscsi_tcp: Unknown symbol iscsi_host_set_param (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_r2tpool_alloc (err 0) iscsi_tcp: Unknown symbol iscsi_session_get_param (err 0) iscsi_tcp: Unknown symbol iscsi_conn_send_pdu (err 0) iscsi_tcp: Unknown symbol iscsi_conn_start (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_r2tpool_free (err 0) iscsi_tcp: Unknown symbol iscsi_host_alloc (err 0) iscsi_tcp: Unknown symbol iscsi_host_add (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_task_xmit (err 0) iscsi_tcp: Unknown symbol iscsi_session_teardown (err 0) iscsi_tcp: Unknown symbol iscsi_conn_get_addr_param (err 0) iscsi_tcp: Unknown symbol iscsi_unregister_transport (err 0) iscsi_tcp: Unknown symbol iscsi_eh_recover_target (err 0) iscsi_tcp: Unknown symbol iscsi_conn_stop (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_recv_skb (err 0) iscsi_tcp: Unknown symbol iscsi_queuecommand (err 0) iscsi_tcp: Unknown symbol iscsi_change_queue_depth (err 0) iscsi_tcp: Unknown symbol iscsi_segment_init_linear (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_conn_get_stats (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_set_max_r2t (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_task_init (err 0) iscsi_tcp: Unknown symbol iscsi_host_remove (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_dgst_header (err 0) iscsi_tcp: Unknown symbol iscsi_tcp_conn_teardown (err 0) Linux video capture interface: v2.00 uvcvideo: Unknown symbol vb2_vmalloc_memops (err 0) Usage: mount -V : print version mount -h : print this help mount : list mounted filesystems mount -l : idem, including volume labels So far the informational part. Next the mounting. The command is `mount [-t fstype] something somewhere'. Details found in /etc/fstab may be omitted. mount -a [-t|-O] ... : mount all stuff from /etc/fstab mount device : mount device at the known place mount directory : mount known device here mount -t type dev dir : ordinary mount command Note that one does not really mount a device, one mounts a filesystem (of the given type) found on the device. One can also mount an already visible directory tree elsewhere: mount --bind olddir newdir or move a subtree: mount --move olddir newdir One can change the type of mount containing the directory dir: mount --make-shared dir mount --make-slave dir mount --make-private dir mount --make-unbindable dir One can change the type of all the mounts in a mount subtree containing the directory dir: mount --make-rshared dir mount --make-rslave dir mount --make-rprivate dir mount --make-runbindable dir A device can be given by name, say /dev/hda1 or /dev/cdrom, or by label, using -L label or by uuid, using -U uuid . Other options: [-nfFrsvw] [-o options] [-p passwdfd]. For many more details, say man 8 mount . configure loopback network interface setting reboot and standby starting php based setup routines step 1 sudo: /usr/sbin/lsscsi: command not found sudo: /usr/sbin/lsscsi: command not found kjournald starting. Commit interval 5 seconds EXT3-fs (sda8): using internal journal EXT3-fs (sda8): recovery complete EXT3-fs (sda8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdb8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdb8): using internal journal EXT3-fs (sdb8): recovery complete EXT3-fs (sdb8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdc8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdc8): using internal journal EXT3-fs (sdc8): recovery complete EXT3-fs (sdc8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdd8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdd8): using internal journal EXT3-fs (sdd8): recovery complete EXT3-fs (sdd8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sde8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sde8): using internal journal EXT3-fs (sde8): recovery complete EXT3-fs (sde8): mounted filesystem with ordered data mode udevd (916): /proc/916/oom_adj is deprecated, please use /proc/916/oom_score_adj instead. mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full duplex, flow control disabled passwd[944]: password for `carmine' changed by user `root' passwd[949]: password for `adelina' changed by user `root' passwd[953]: password for `lucio' changed by user `root' passwd[957]: password for `veronica' changed by user `root' start portmap service starting php based setup routines step2 starting php based setup routines step3 starting php based setup routines step banner php based setup routines finished web permission on resolv.conf set device tuning for dms performance ------------------------ rcS finished ------------------------ list boot.log file start boot log detect and set platform 5big1 UIMAGE-26394-5BIG1-20 5big1 update dev nodes booting using root file system... make dev node for buttons... make dev node for tun device... enable IP forwarding... start buttons control daemon device = 5big1 source = buttons-nwsp2 buttons-nwsp2 daemon started initializing date Wed Nov 16 12:00:00 GMT+1 2011 create temporary passwd file run udevstart to update dev nodes when necessary inserting kernel modules: modprobe: module 'iscsi_trgt' not found modprobe: module 'libiscsi' not found modprobe: module 'libiscsi_tcp' not found modprobe: module 'scsi_transport_iscsi' not found modprobe: 'iscsi_tcp.ko': unknown symbol in module or invalid parameter modprobe: module 'videobuf2_vmalloc' not found modprobe: 'uvcvideo.ko': unknown symbol in module or invalid parameter configure loopback netwerk interface setting reboot and standby 5big1 rebootd-isp1 5big1 standbyd-isp1 starting php based setup routines step 1 * Found XML database configuration file... [ OK ] * Configuring Disks... [ OK ] * Starting mount of volumes... - Mounting volume Vol-a: [ OK ] - Mounting volume Vol-b: [ OK ] - Mounting volume Vol-c: [ OK ] - Mounting volume Vol-d: [ OK ] - Mounting volume Vol-e: [ OK ] * Finishing mount of volumes... [ OK ] * Generating Hosts File... [ OK ] * Configuring System Hostname... [ OK ] * Configuring Samba... [ OK ] * Configuring LAN interface... [ OK ] * Starting udevd... [ OK ] * Starting web server... [ OK ] * Initializing Timezone... [ OK ] * Configuring Samba... [ OK ] * Configuring System Users... Root password: use default password Set users, linux and samba accounts [ OK ] * Starting syncawayd... [ OK ] * Starting Fvdw-sl Discovery Daemon... [ OK ] start portmap service starting php based setup routines step 2 * Starting dropbear... [ OK ] * Kill temporary dropbear... [ OK ] starting php based setup routines step 3 Warning: require_once(/etc/finc/vpnfunc_get_status.finc): failed to open stream: No such file or directory in /etc/init.d/rc.bootup3 on line 13 Fatal error: require_once(): Failed opening required '/etc/finc/vpnfunc_get_status.finc' (include_path='.:/usr/htdocs/php:/usr/htdocs:/usr/htdocs/inc:/usr/htdocs/status') in /etc/init.d/rc.bootup3 on line 13 starting php based setup routines step banner *** fvdw-sl NAS firmware This is fvdw-sl version: fvdw-sl 15.0 built on: September 30 2013 LAN IP address: 192.168.1.71 (static) Port configuration: LAN -> eth0 php based setup routines finished web permission on resolv.conf set device tuning for dms performance rcS finished /bin/sh: can't access tty; job control turned off ~ #

(both kernel before this new)
numerous tests that I'm doing, I have noticed that copying files on the NAS is always successful .. while if I want to withdraw from the nas, files or multiple files, the size of 600mb to 3gb etc, I drop the connection and very often I get the message unable to copy files to the PC (ABORT RETRY IGNORE) until in some cases not at all, and then the copy I have to reboot the nas.

From what can be the problem? state that does not appear on the serial console error on these issues

by **fvdw** » Wed Jan 01, 2014 11:51 am

I see that that you still miss some 3.9.5 modules in the serial output
I will sent these today

about the 0x8007003B.error

Think this is a problem of your windows PC as it is a network communication fault
I don't know if it is a solution but you can check the settings of your network adapter
if these are present
Large Send offload(IPv4)
Large Send offload v2 (IPv4)
Large Send offload-offload v2 (IPv6)

And if these are activate disable them (clear the checkbox).
This also will improve transfer speeds

by **fvdw** » Wed Jan 01, 2014 1:05 pm

I sent you an update of the modules for 3.9.5 kernel this contains also the missing ones in previous package

by **taetae** » Wed Jan 01, 2014 5:42 pm

Code: Select all: Waiting for LUMP (5) no lump receive; continuing Reset IDE: Marvell Serial ATA Adapter Found adapter at bus 1, device 7 ... Scanning channels Device 0: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0218180 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 1: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0410979 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 2: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0424246 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 3: OK Model: WDC WD20EZRX-00D8PB0 Firm: 80.00A80 Ser#: WD-WMC4M0219436 Type: Hard Disk Supports 48-bit addressing Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512) Device 4: OK Model: WDC WD5000AADS-00S9B0 Firm: 01.00A01 Ser#: WD-WCAV90478832 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Loading from IDE device 0, partition 6: Name: hda6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 1, partition 6: Name: hdb6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 2, partition 6: Name: hdc6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 3, partition 6: Name: hdd6 Type: U-Boot ** Bad Magic Number ** Loading from IDE device 4, partition 6: Name: hde6 Type: U-Boot Image Name: Linux-3.9.5 Created: 2014-01-01 14:21:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1880848 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 ## Booting image at 00400000 ... Image Name: Linux-3.9.5 Created: 2014-01-01 14:21:22 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1880848 Bytes = 1.8 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK Starting kernel ... Uncompressing Linux... done, booting the kernel. Booting Linux on physical CPU 0x0 Linux version 3.9.5 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #23 Wed Jan 1 15:20:55 GMT+1 2014 CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177 CPU: VIVT data cache, VIVT instruction cache Machine: LaCie 5Big1 Network Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Clearing invalid memory bank 0KB@0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x00000000 Ignoring unrecognised tag 0x41000403 Memory policy: ECC disabled, Data cache writeback Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0 PID hash table entries: 512 (order: -1, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) __ex_table already sorted, skipping sort Memory: 128MB = 128MB total Memory: 125956k/125956k available, 5116k reserved, 0K highmem Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xc8800000 - 0xff000000 ( 872 MB) lowmem : 0xc0000000 - 0xc8000000 ( 128 MB) modules : 0xbf000000 - 0xc0000000 ( 16 MB) .text : 0xc0008000 - 0xc0364fdc (3444 kB) .init : 0xc0365000 - 0xc03840d8 ( 125 kB) .data : 0xc0386000 - 0xc03acd80 ( 156 kB) .bss : 0xc03acd80 - 0xc03db7fc ( 187 kB) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:64 sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms Console: colour dummy device 80x30 Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok Setting up static identity map for 0xc029bbb8 - 0xc029bbf4 NET: Registered protocol family 16 DMA: preallocated 1024 KiB pool for atomic coherent allocations Register Driver 'dummy' 5big1 init started Orion ID: MV88F5281-D0. TCLK=166666667. Orion: Applying 5281 D0 WFI workaround. 5big1 init 1 5big1 init 2 net5big: powering up SATA drives 5big1 init 3 5big1 init 4 5big1 init 5 5big1 init 6 5big1 init 7 5big1 init 8 5big1 init 9 5big1 init 10 5big1 init 11 5big1 init 12 net5big: turning off power-off control GPIO net5big: Flash writing is not yet supported. 5big1 init end net5big_pci_preinit failed to gpio_request 20 PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] PCI: bus0: Fast back to back transfers disabled PCI host bridge to bus 0000:01 pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff] pci_bus 0000:01: root bus resource [io 0x10000-0x1ffff] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] PCI: bus1: Fast back to back transfers enabled pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit] pci 0000:01:07.0: BAR 2: assigned [io 0x10000-0x100ff] bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized Register Driver 'Generic PHY' Register Driver 'usbfs' usbcore: registered new interface driver usbfs Register Driver 'hub' usbcore: registered new interface driver hub Register Driver 'usb' usbcore: registered new device driver usb Register Driver 'i2c-gpio' Switching to clocksource orion_clocksource NET: Registered protocol family 2 TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP: reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Register Driver 'alarmtimer' VFS: Disk quotas dquot_6.5.2 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) msgmni has been set to 246 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253) io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) Register Driver 'mv_xor' mv_xor mv_xor.0: Marvell shared XOR driver mv_xor mv_xor.0: Self-test copy failed compare, disabling Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled Register Driver 'serial8250' serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A console [ttyS0] enabled Register Driver 'serial' brd: module loaded loop: module loaded Register Driver 'at24' Register Driver 'eeprom' Register Driver 'sd' Register Driver 'ahci' Register Driver 'sata_mv' sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx scsi0 : sata_mv scsi1 : sata_mv scsi2 : sata_mv scsi3 : sata_mv scsi4 : sata_mv scsi5 : sata_mv scsi6 : sata_mv scsi7 : sata_mv ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52 ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52 ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52 ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52 ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52 ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52 ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52 ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52 Register Driver 'sata_mv' sata_mv sata_mv.0: cannot get optional clkdev sata_mv sata_mv.0: slots 32 ports 5 scsi8 : sata_mv scsi9 : sata_mv scsi10 : sata_mv scsi11 : sata_mv scsi12 : sata_mv ata9: SATA max UDMA/133 irq 29 ata10: SATA max UDMA/133 irq 29 ata11: SATA max UDMA/133 irq 29 ata12: SATA max UDMA/133 irq 29 ata13: SATA max UDMA/133 irq 29 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu> ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu> Register Driver 'mv643xx_eth' mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4 libphy: mv643xx_eth smi: probed Register Driver 'mv643xx_eth_port' mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:8b:60:2b mousedev: PS/2 mouse device common for all mice Register Driver 'rtc-ds1307' Register Driver 'rtc-ds1374' Register Driver 'rtc-rs5c372' i2c /dev entries driver Register Driver 'mv64xxx_i2c' rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6 rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0 at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write Register Driver 'g762' g762 probe started g762 probe 1 g762 probe 2 g762 probe 3 g762 probe 4 g762 probe 5 g762 probe 6 g762 probe 7 Register Driver 'gpio-fan' Register Driver 'lm75' Register Driver 'lm77' Register Driver 'leds-gpio' Register Driver 'mv_crypto' Netfilter messages via NETLINK v0.30. IPv4 over IPv4 tunneling driver TCP: cubic registered NET: Registered protocol family 17 NET: Registered protocol family 5 VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0 console [netcon0] enabled netconsole: network logging started rtc-rs5c372 0-0032: setting system clock to 2014-01-05 02:37:26 UTC (1388889446) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata1.00: configured for UDMA/133 scsi 0:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 0 device-name= sata_mv fvdw2 disk index after get_sd_name = 4 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sde sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 0:0:0:0: [sde] 4096-byte physical blocks sd 0:0:0:0: [sde] Write Protect is off sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sde: sde4 < sde5 sde6 sde7 sde8 > sd 0:0:0:0: [sde] Attached SCSI disk ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata9: failed to resume link (SControl 0) ata9: SATA link down (SStatus 0 SControl 0) ata2.00: configured for UDMA/133 scsi 1:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 1 device-name= sata_mv fvdw2 disk index after get_sd_name = 3 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdd sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 1:0:0:0: [sdd] 4096-byte physical blocks sd 1:0:0:0: [sdd] Write Protect is off sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdd: sdd4 < sdd5 sdd6 sdd7 sdd8 > sd 1:0:0:0: [sdd] Attached SCSI disk ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata3.00: configured for UDMA/133 scsi 2:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 2 device-name= sata_mv fvdw2 disk index after get_sd_name = 2 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdc sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 2:0:0:0: [sdc] 4096-byte physical blocks sd 2:0:0:0: [sdc] Write Protect is off sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdc: sdc4 < sdc5 sdc6 sdc7 sdc8 > sd 2:0:0:0: [sdc] Attached SCSI disk ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133 ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata4.00: configured for UDMA/133 scsi 3:0:0:0: Direct-Access ATA WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 3 device-name= sata_mv fvdw2 disk index after get_sd_name = 1 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sdb sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) sd 3:0:0:0: [sdb] 4096-byte physical blocks sd 3:0:0:0: [sdb] Write Protect is off sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sdb: sdb4 < sdb5 sdb6 sdb7 sdb8 > sd 3:0:0:0: [sdb] Attached SCSI disk ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133 ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32) ata5.00: configured for UDMA/133 scsi 4:0:0:0: Direct-Access ATA WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5 fvdw1 disk index before get_sd_name = 4 device-name= sata_mv fvdw2 disk index after get_sd_name = 0 fvdw3 prefix[0]=s prefix[1]=d fvdw4 diskname = sda sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB) sd 4:0:0:0: [sda] Write Protect is off sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 > sd 4:0:0:0: [sda] Attached SCSI disk ata6: SATA link down (SStatus 0 SControl 300) ata7: SATA link down (SStatus 0 SControl 300) ata8: SATA link down (SStatus 0 SControl 300) ata10: failed to resume link (SControl 0) ata10: SATA link down (SStatus 0 SControl 0) ata11: failed to resume link (SControl 0) ata11: SATA link down (SStatus 0 SControl 0) ata12: failed to resume link (SControl 0) ata12: SATA link down (SStatus 0 SControl 0) ata13: failed to resume link (SControl 0) ata13: SATA link down (SStatus 0 SControl 0) kjournald starting. Commit interval 5 seconds EXT3-fs (sda7): mounted filesystem with ordered data mode VFS: Mounted root (ext3 filesystem) readonly on device 8:71. Freeing init memory: 124K start rcS set global environment params mount proc remount root file system rw EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sda7): using internal journal mount sysfs start boot log detect and set platform 5big1 update dev nodes booting using root file system... make dev node for buttons... mkdir: can't create directory '/dev/input': File exists mknod: /dev/input/event0: File exists make dev node for tun device... mknod: /dev/net/tun: File exists enable IP forwarding... start buttons control daemon create temporary passwd file run udevstart to update dev nodes when necessary mkdir: can't create directory 'rw_fs': File exists kjournald starting. Commit interval 5 seconds EXT3-fs (sda5): using internal journal EXT3-fs (sda5): recovery complete EXT3-fs (sda5): mounted filesystem with ordered data mode Setting up swapspace version 1, size = 526413824 bytes UUID=a75ba44f-854e-4d8c-85a4-f24da5380ec2 Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k inserting kernel modules: NTFS driver 2.1.30 [Flags: R/W MODULE]. fuse init (API version 7.21) Register Driver 'usblp' usbcore: registered new interface driver usblp RPC: Registered named UNIX socket transport module. RPC: Registered udp transport module. RPC: Registered tcp transport module. RPC: Registered tcp NFSv4.1 backchannel transport module. Installing knfsd (copyright (C) 1996 okir@monad.swb.de). iscsi_trgt: version magic '3.9.5 preempt mod_unload ARMv5 p2v8 ' should be '3.9.5 mod_unload ARMv5 ' Loading iSCSI transport class v2.0-870. iscsi: registered transport (tcp) Linux video capture interface: v2.00 uvcvideo: Unable to create debugfs directory Register Driver 'uvcvideo' usbcore: registered new interface driver uvcvideo USB Video Class driver (1.1.1) Usage: mount -V : print version mount -h : print this help mount : list mounted filesystems mount -l : idem, including volume labels So far the informational part. Next the mounting. The command is `mount [-t fstype] something somewhere'. Details found in /etc/fstab may be omitted. mount -a [-t|-O] ... : mount all stuff from /etc/fstab mount device : mount device at the known place mount directory : mount known device here mount -t type dev dir : ordinary mount command Note that one does not really mount a device, one mounts a filesystem (of the given type) found on the device. One can also mount an already visible directory tree elsewhere: mount --bind olddir newdir or move a subtree: mount --move olddir newdir One can change the type of mount containing the directory dir: mount --make-shared dir mount --make-slave dir mount --make-private dir mount --make-unbindable dir One can change the type of all the mounts in a mount subtree containing the directory dir: mount --make-rshared dir mount --make-rslave dir mount --make-rprivate dir mount --make-runbindable dir A device can be given by name, say /dev/hda1 or /dev/cdrom, or by label, using -L label or by uuid, using -U uuid . Other options: [-nfFrsvw] [-o options] [-p passwdfd]. For many more details, say man 8 mount . configure loopback network interface setting reboot and standby starting php based setup routines step 1 sudo: /usr/sbin/lsscsi: command not found sudo: /usr/sbin/lsscsi: command not found kjournald starting. Commit interval 5 seconds EXT3-fs (sda8): using internal journal EXT3-fs (sda8): recovery complete EXT3-fs (sda8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdb8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdb8): using internal journal EXT3-fs (sdb8): recovery complete EXT3-fs (sdb8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdc8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdc8): using internal journal EXT3-fs (sdc8): recovery complete EXT3-fs (sdc8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sdd8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sdd8): using internal journal EXT3-fs (sdd8): recovery complete EXT3-fs (sdd8): mounted filesystem with ordered data mode kjournald starting. Commit interval 5 seconds EXT3-fs (sde8): warning: maximal mount count reached, running e2fsck is recommended EXT3-fs (sde8): using internal journal EXT3-fs (sde8): recovery complete EXT3-fs (sde8): mounted filesystem with ordered data mode udevd (934): /proc/934/oom_adj is deprecated, please use /proc/934/oom_score_adj instead. mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled passwd[962]: password for `carmine' changed by user `root' passwd[967]: password for `adelina' changed by user `root' passwd[971]: password for `lucio' changed by user `root' passwd[975]: password for `veronica' changed by user `root' start portmap service starting php based setup routines step2 starting php based setup routines step3 starting php based setup routines step banner php based setup routines finished web permission on resolv.conf set device tuning for dms performance ------------------------ rcS finished ------------------------ list boot.log file start boot log detect and set platform 5big1 UIMAGE-26394-5BIG1-20 5big1 update dev nodes booting using root file system... make dev node for buttons... make dev node for tun device... enable IP forwarding... start buttons control daemon device = 5big1 source = buttons-nwsp2 buttons-nwsp2 daemon started Sun Jan 5 03:37:35 GMT+1 2014 create temporary passwd file run udevstart to update dev nodes when necessary inserting kernel modules: modprobe: 'iscsi_trgt.ko': invalid module format configure loopback netwerk interface setting reboot and standby 5big1 rebootd-isp1 5big1 standbyd-isp1 starting php based setup routines step 1 * Found XML database configuration file... [ OK ] * Configuring Disks... [ OK ] * Starting mount of volumes... - Mounting volume Vol-a: [ OK ] - Mounting volume Vol-b: [ OK ] - Mounting volume Vol-c: [ OK ] - Mounting volume Vol-d: [ OK ] - Mounting volume Vol-e: [ OK ] * Finishing mount of volumes... [ OK ] * Generating Hosts File... [ OK ] * Configuring System Hostname... [ OK ] * Configuring Samba... [ OK ] * Configuring LAN interface... [ OK ] * Starting udevd... [ OK ] * Starting web server... [ OK ] * Initializing Timezone... [ OK ] * Configuring Samba... [ OK ] * Configuring System Users... Root password: use default password Set users, linux and samba accounts [ OK ] * Starting syncawayd... [ OK ] * Starting Fvdw-sl Discovery Daemon... [ OK ] start portmap service starting php based setup routines step 2 * Starting dropbear... [ OK ] * Kill temporary dropbear... [ OK ] starting php based setup routines step 3 * Starting daemon update Hosts File... [ OK ] * Starting Disk Temperature Guard... [ OK ] starting php based setup routines step banner *** fvdw-sl NAS firmware This is fvdw-sl version: fvdw-sl 15.0 built on: September 30 2013 LAN IP address: 192.168.1.71 (static) Port configuration: LAN -> eth0 php based setup routines finished web permission on resolv.conf set device tuning for dms performance rcS finished /bin/sh: can't access tty; job control turned off ~ #

plugout.net

lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Re: lacie 5 big network v.1 please support for fvdw

Who is online