lacie 5 big network v.1 please support for fvdw

[fvdw]

Hi tatae

this part of the rcs output proves that you did not install the file I have sent you to enable reboot and shutdown, it mentions unknown platform
It seems to boot form sda7 as it mentions "booting from root file system"
I need to find my post back with the file you need to install

Code: Select all

------------------------
rcS finished
------------------------
 list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using  root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = unknown
source =
Thu Dec 26 05:59:02 GMT+1 2013

[fvdw]

Hi tatae in the attachment two file that should get your shutdown and reboot buttons working in the web interface

unpack the zip archive in the share with name public
You should have a file with name nas_bin and platform_check.sh
Connect via ssh and give following commands

Code: Select all

cp /share/1000/public/nas_bin /etc/nas_bin
chmod 755 /etc/nas_bin
cp /share/1000/public/platform_check.sh /etc/platform_check.sh
chmod 755 /etc/platform_check.sh

After rebooting your 5big1 the buttons in the web interface should work.

[taetae]

I did this as in your previous post

Code: Select all

cp /share/1000/public/nas_bin /etc/nas_bin
chmod 755 /etc/nas_bin

Now I am going to do the other files posted by you and tell you to restart


ok

Code: Select all

/share/1000/Terra/5big1-nas_bin # cp nas_bin /etc/nas_bin
/share/1000/Terra/5big1-nas_bin # chmod 755 /etc/nas_bin
/share/1000/Terra/5big1-nas_bin # cp platform_check.sh  /etc/platform_check.sh
/share/1000/Terra/5big1-nas_bin # chmod 755 /etc/platform_check.sh
/share/1000/Terra/5big1-nas_bin # reboot


Code: Select all

-----------------------
rcS finished
------------------------
 list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using  root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = unknown
source =
Thu Dec 26 22:34:52 GMT+1 2013
create temporary passwd file
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
setting reboot and standby
unknown

unknown

starting php based setup routines step 1


[taetae]

Code: Select all

/share/1000/Terra/5big1-nas_bin # cp nas_bin /etc/nas_bin
/share/1000/Terra/5big1-nas_bin # chmod 755 /etc/nas_bin
/share/1000/Terra/5big1-nas_bin # cp platform_check.sh  /etc/platform_check.sh
/share/1000/Terra/5big1-nas_bin # chmod 755 /etc/platform_check.sh
/share/1000/Terra/5big1-nas_bin # reboot
/share/1000/Terra/5big1-nas_bin # killall: zfs: no process killed
killall: zxtract: no process killed
killall: zappdms: no process killed
killall: udhcpc: no process killed
killall: syncawayd: no process killed
killall: ntpd: no process killed
killall: fanctld: no process killed
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
sd 4:0:0:0: [sda] Synchronizing SCSI cache
sd 3:0:0:0: [sdb] Synchronizing SCSI cache
sd 2:0:0:0: [sdc] Synchronizing SCSI cache
sd 1:0:0:0: [sdd] Synchronizing SCSI cache
sd 0:0:0:0: [sde] Synchronizing SCSI cache
Restarting system.

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: RD-88F5281-LaCie LE

U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9

U-Boot code: 00200000 -> 0026FFF0  BSS: -> 00283280

Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz

DRAM CS[0] base 0x00000000   size 128MB
DRAM Total size 128MB  32bit width
[4096kB@ffc00000] Flash:  4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
*** Warning - bad CRC, using default environment


CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.

USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net:   egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot:  0
Waiting for LUMP (5)
no lump receive; continuing

Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
  Device 0: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0218180
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 1: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0410979
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 2: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0424246
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 3: OK
Model: WDC WD20EZRX-00D8PB0                     Firm: 80.00A80 Ser#:      WD-WMC4M0219436
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
  Device 4: OK
Model: WDC WD5000AADS-00S9B0                    Firm: 01.00A01 Ser#:      WD-WCAV90478832
            Type: Hard Disk
            Supports 48-bit addressing
            Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)


Loading from IDE device 0, partition 6: Name: hda6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 1, partition 6: Name: hdb6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 2, partition 6: Name: hdc6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 3, partition 6: Name: hdd6
  Type: U-Boot

** Bad Magic Number **

Loading from IDE device 4, partition 6: Name: hde6
  Type: U-Boot
   Image Name:   Linux-2.6.39.4
   Created:      2013-09-23  18:39:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1871800 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
## Booting image at 00400000 ...
   Image Name:   Linux-2.6.39.4
   Created:      2013-09-23  18:39:53 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1871800 Bytes =  1.8 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
Linux version 2.6.39.4 (root@fvdwsl-5big2.local) (gcc version 4.5.4 (GCC) ) #20 PREEMPT Mon Sep 23 19:39:28 GMT+1 2013
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=00053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie 5Big1 Network
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Clearing invalid memory bank 0KB@0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 32512
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro boardType=mv88F5281 productType=5Big reset=0
PID hash table entries: 512 (order: -1, 2048 bytes)
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 128MB = 128MB total
Memory: 125992k/125992k available, 5080k reserved, 0K highmem
Virtual kernel memory layout:
    vector  : 0xffff0000 - 0xffff1000   (   4 kB)
    fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
    DMA     : 0xffc00000 - 0xffe00000   (   2 MB)
    vmalloc : 0xc8800000 - 0xfd800000   ( 848 MB)
    lowmem  : 0xc0000000 - 0xc8000000   ( 128 MB)
    modules : 0xbf000000 - 0xc0000000   (  16 MB)
      .init : 0xc0008000 - 0xc0028000   ( 128 kB)
      .text : 0xc0028000 - 0xc03a6000   (3576 kB)
      .data : 0xc03a6000 - 0xc03c1a40   ( 111 kB)
SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Preemptable hierarchical RCU implementation.
        RCU-based detection of stalled CPUs is disabled.
        Verbose stalled-CPUs detection is disabled.
NR_IRQS:64
sched_clock: 32 bits at 166MHz, resolution 5ns, wraps every 25769ms
Calibrating delay loop... 498.89 BogoMIPS (lpj=2494464)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5281-D0. TCLK=166666667.
Orion: Applying 5281 D0 WFI workaround.
net5big: powering up SATA drives
net5big: turning off power-off control GPIO
net5big: Flash writing is not yet supported.
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:01:07.0: BAR 0: assigned [mem 0xe8000000-0xe80fffff 64bit]
pci 0000:01:07.0: BAR 0: set to [mem 0xe8000000-0xe80fffff 64bit] (PCI address [0xe8000000-0xe80fffff])
pci 0000:01:07.0: BAR 2: assigned [io  0x100000-0x1000ff]
pci 0000:01:07.0: BAR 2: set to [io  0x100000-0x1000ff] (PCI address [0x100000-0x1000ff])
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
NetWinder Floating Point Emulator V0.97 (double precision)
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 246
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv 0000:01:07.0: version 1.28
sata_mv 0000:01:07.0: Gen-II 32 slots 8 ports SCSI mode IRQ via INTx
scsi0 : sata_mv
scsi1 : sata_mv
scsi2 : sata_mv
scsi3 : sata_mv
scsi4 : sata_mv
scsi5 : sata_mv
scsi6 : sata_mv
scsi7 : sata_mv
ata1: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8022000 irq 52
ata2: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8024000 irq 52
ata3: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8026000 irq 52
ata4: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8028000 irq 52
ata5: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8032000 irq 52
ata6: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8034000 irq 52
ata7: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8036000 irq 52
ata8: SATA max UDMA/133 mmio m1048576@0xe8000000 port 0xe8038000 irq 52
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 5
scsi8 : sata_mv
scsi9 : sata_mv
scsi10 : sata_mv
scsi11 : sata_mv
scsi12 : sata_mv
ata9: SATA max UDMA/133 irq 29
ata10: SATA max UDMA/133 irq 29
ata11: SATA max UDMA/133 irq 29
ata12: SATA max UDMA/133 irq 29
ata13: SATA max UDMA/133 irq 29
mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
mv643xx_eth_port mv643xx_eth_port.0: eth0: port 0 with MAC address 00:d0:4b:8b:60:2b
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP MPPE Compression module registered
NET: Registered protocol family 24
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
usbcore: registered new interface driver ipheth
console [netcon0] enabled
netconsole: network logging started
aoe: AoE v47 initialised.
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
input: gpio-keys as /devices/platform/gpio-keys/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372b found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
at24 0-0050: 1024 byte 24c08 EEPROM, writable, 1 bytes/write
mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
mv_xor mv_xor.0: Self-test copy failed compare, disabling
mv_xor mv_xor.1: Self-test copy failed compare, disabling
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1968 buckets, 7872 max)
IPv4 over IPv4 tunneling driver
TCP cubic registered
NET: Registered protocol family 17
NET: Registered protocol family 5
NET: Registered protocol family 37
VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 0
rtc-rs5c372 0-0032: setting system clock to 2013-12-26 21:34:43 UTC (1388093683)
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata1.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access     ATA      WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 0
fvdw2 disk indexfvdw 0
fvdw3 disk indexfvdw 4
fvdw4 disk diskname= sde
sd 0:0:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 0:0:0:0: [sde] 4096-byte physical blocks
sd 0:0:0:0: [sde] Write Protect is off
sd 0:0:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sde: sde4 < sde5 sde6 sde7 sde8 >
sd 0:0:0:0: [sde] Attached SCSI disk
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata9: failed to resume link (SControl 0)
ata9: SATA link down (SStatus 0 SControl 0)
ata2.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access     ATA      WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 1
fvdw2 disk indexfvdw 1
fvdw3 disk indexfvdw 3
fvdw4 disk diskname= sdd
sd 1:0:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 1:0:0:0: [sdd] 4096-byte physical blocks
sd 1:0:0:0: [sdd] Write Protect is off
sd 1:0:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdd: sdd4 < sdd5 sdd6 sdd7 sdd8 >
sd 1:0:0:0: [sdd] Attached SCSI disk
ata3: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata3.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata3.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access     ATA      WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 2
fvdw2 disk indexfvdw 2
fvdw3 disk indexfvdw 2
fvdw4 disk diskname= sdc
sd 2:0:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 2:0:0:0: [sdc] 4096-byte physical blocks
sd 2:0:0:0: [sdc] Write Protect is off
sd 2:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdc: sdc4 < sdc5 sdc6 sdc7 sdc8 >
sd 2:0:0:0: [sdc] Attached SCSI disk
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata4.00: ATA-9: WDC WD20EZRX-00D8PB0, 80.00A80, max UDMA/133
ata4.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata4.00: configured for UDMA/133
scsi 3:0:0:0: Direct-Access     ATA      WDC WD20EZRX-00D 80.0 PQ: 0 ANSI: 5
fvdw1 disk index 3
fvdw2 disk indexfvdw 3
fvdw3 disk indexfvdw 1
fvdw4 disk diskname= sdb
sd 3:0:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 3:0:0:0: [sdb] 4096-byte physical blocks
sd 3:0:0:0: [sdb] Write Protect is off
sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb: sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 3:0:0:0: [sdb] Attached SCSI disk
ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata5.00: ATA-8: WDC WD5000AADS-00S9B0, 01.00A01, max UDMA/133
ata5.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata5.00: configured for UDMA/133
scsi 4:0:0:0: Direct-Access     ATA      WDC WD5000AADS-0 01.0 PQ: 0 ANSI: 5
fvdw1 disk index 4
fvdw2 disk indexfvdw 4
fvdw3 disk indexfvdw 0
fvdw4 disk diskname= sda
sd 4:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 4:0:0:0: [sda] Write Protect is off
sd 4:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 4:0:0:0: [sda] Attached SCSI disk
ata6: SATA link down (SStatus 0 SControl 300)
ata7: SATA link down (SStatus 0 SControl 300)
ata8: SATA link down (SStatus 0 SControl 300)
ata10: failed to resume link (SControl 0)
ata10: SATA link down (SStatus 0 SControl 0)
ata11: failed to resume link (SControl 0)
ata11: SATA link down (SStatus 0 SControl 0)
ata12: failed to resume link (SControl 0)
ata12: SATA link down (SStatus 0 SControl 0)
ata13: failed to resume link (SControl 0)
ata13: SATA link down (SStatus 0 SControl 0)
EXT3-fs: barriers not enabled
EXT3-fs (sda7): mounted filesystem with ordered data mode
kjournald starting.  Commit interval 5 seconds
VFS: Mounted root (ext3 filesystem) readonly on device 8:71.
Freeing init memory: 128K
start rcS
set global environment params
mount proc
remount root file system rw
EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
mount sysfs
start boot log
detect and set platform
unknown
update dev nodes
booting using  root file system...
make dev node for buttons...
mkdir: can't create directory '/dev/input': File exists
mknod: /dev/input/event0: File exists
make dev node for tun device...
mknod: /dev/net/tun: File exists
enable IP forwarding...
start buttons control daemon
/etc/init.d/rcS: line 522: /usr/sbin/buttonsd: Permission denied
create temporary passwd file
run udevstart to update dev nodes when necessary
mkdir: can't create directory 'rw_fs': File exists
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Setting up swapspace version 1, size = 526413824 bytes
UUID=750b2715-ecc4-41cc-8633-15d3c663fb19
Adding 514076k swap on /dev/sda3.  Priority:-1 extents:1 across:514076k
inserting kernel modules:
NTFS driver 2.1.30 [Flags: R/W MODULE].
fuse init (API version 7.16)
usbcore: registered new interface driver usblp
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
iSCSI Enterprise Target Software - version trunk
iscsi_trgt: Registered io type fileio
iscsi_trgt: Registered io type blockio
iscsi_trgt: Registered io type nullio
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Linux video capture interface: v2.00
usbcore: registered new interface driver uvcvideo
USB Video Class driver (v1.0.0)
Usage: mount -V                 : print version
       mount -h                 : print this help
       mount                    : list mounted filesystems
       mount -l                 : idem, including volume labels
So far the informational part. Next the mounting.
The command is `mount [-t fstype] something somewhere'.
Details found in /etc/fstab may be omitted.
       mount -a [-t|-O] ...     : mount all stuff from /etc/fstab
       mount device             : mount device at the known place
       mount directory          : mount known device here
       mount -t type dev dir    : ordinary mount command
Note that one does not really mount a device, one mounts
a filesystem (of the given type) found on the device.
One can also mount an already visible directory tree elsewhere:
       mount --bind olddir newdir
or move a subtree:
       mount --move olddir newdir
One can change the type of mount containing the directory dir:
       mount --make-shared dir
       mount --make-slave dir
       mount --make-private dir
       mount --make-unbindable dir
One can change the type of all the mounts in a mount subtree
containing the directory dir:
       mount --make-rshared dir
       mount --make-rslave dir
       mount --make-rprivate dir
       mount --make-runbindable dir
A device can be given by name, say /dev/hda1 or /dev/cdrom,
or by label, using  -L label  or by uuid, using  -U uuid .
Other options: [-nfFrsvw] [-o options] [-p passwdfd].
For many more details, say  man 8 mount .
configure loopback network interface
setting reboot and standby
starting php based setup routines step 1
sudo: /usr/sbin/lsscsi: command not found
sudo: /usr/sbin/lsscsi: command not found
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdb8): using internal journal
EXT3-fs (sdb8): recovery complete
EXT3-fs (sdb8): mounted filesystem with ordered data mode
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdc8): using internal journal
EXT3-fs (sdc8): recovery complete
EXT3-fs (sdc8): mounted filesystem with ordered data mode
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sdd8): using internal journal
EXT3-fs (sdd8): recovery complete
EXT3-fs (sdd8): mounted filesystem with ordered data mode
EXT3-fs: barriers not enabled
kjournald starting.  Commit interval 5 seconds
EXT3-fs (sde8): using internal journal
EXT3-fs (sde8): recovery complete
EXT3-fs (sde8): mounted filesystem with ordered data mode
udevd (822): /proc/822/oom_adj is deprecated, please use /proc/822/oom_score_adj instead.
mv643xx_eth_port mv643xx_eth_port.0: eth0: link up, 1000 Mb/s, full duplex, flow control disabled
passwd[850]: password for `carmine' changed by user `root'
passwd[855]: password for `adelina' changed by user `root'
passwd[859]: password for `lucio' changed by user `root'
passwd[863]: password for `veronica' changed by user `root'
start portmap service
starting php based setup routines step2
starting php based setup routines step3
starting php based setup routines step banner
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
------------------------
rcS finished
------------------------
 list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using  root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = unknown
source =
Thu Dec 26 22:34:52 GMT+1 2013
create temporary passwd file
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
setting reboot and standby
unknown

unknown

starting php based setup routines step 1

 * Found XML database configuration file...      [ OK ]
 * Configuring Disks...                                  [ OK ]
 * Starting mount of volumes...
   - Mounting volume Vol-a:              [ OK ]
   - Mounting volume Vol-b:              [ OK ]
   - Mounting volume Vol-c:              [ OK ]
   - Mounting volume Vol-d:              [ OK ]
   - Mounting volume Vol-e:              [ OK ]
 * Finishing mount of volumes...                 [ OK ]
 * Generating Hosts File...                      [ OK ]
 * Configuring System Hostname...                [ OK ]
 * Configuring Samba...                                  [ OK ]
 * Configuring LAN interface...                  [ OK ]
 * Starting udevd...                                     [ OK ]
 * Starting web server...                                [ OK ]
 * Initializing Timezone...                      [ OK ]
 * Configuring Samba...                                  [ OK ]
 * Configuring System Users...
        Root password: use default password
        Set users, linux and samba accounts      [ OK ]
 * Starting Fvdw-sl Discovery Daemon...  [ OK ]
start portmap service
starting php based setup routines step 2
 * Starting dropbear...                                  [ OK ]
 * Kill temporary dropbear...                    [ OK ]
starting php based setup routines step 3
 * Starting daemon update Hosts File...  [ OK ]
 * Starting Disk Temperature Guard...    [ OK ]
starting php based setup routines step banner


*** fvdw-sl NAS firmware
    This is fvdw-sl version: fvdw-sl 15.0
    built on: September 30 2013

    LAN IP address: 192.168.1.71 (static)

    Port configuration:

    LAN   -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
rcS finished
/bin/sh: can't access tty; job control turned off
~ #


[fvdw]

mmm....unknown platform

still we get this

Code: Select all

 list boot.log file
start boot log
detect and set platform
unknown
unknown
unknown
update dev nodes
booting using  root file system...
make dev node for buttons...
make dev node for tun device...
e

:scratch need to verify some things

[fvdw]

found the error in the platform_check file it was missing a 1 after 5Big

install this one and try again

Code: Select all

/share/1000/Terra/5big1-nas_bin # cp platform_check.sh  /etc/platform_check.sh
/share/1000/Terra/5big1-nas_bin # chmod 755 /etc/platform_check.sh

[taetae]

:applause

Code: Select all

------------------------
rcS finished
------------------------
 list boot.log file
start boot log
detect and set platform
5big1
UIMAGE-26394-5BIG1-20
5big1
update dev nodes
booting using  root file system...
make dev node for buttons...
make dev node for tun device...
enable IP forwarding...
start buttons control daemon
device = 5big1
source = buttons-nwsp2
buttons-nwsp2 daemon started
Thu Dec 26 23:51:07 GMT+1 2013
create temporary passwd file
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
setting reboot and standby
5big1
rebootd-isp1
5big1
standbyd-isp1
starting php based setup routines step 1

 * Found XML database configuration file...      [ OK ]
 * Configuring Disks...                                  [ OK ]
 * Starting mount of volumes...
   - Mounting volume Vol-a:              [ OK ]
   - Mounting volume Vol-b:              [ OK ]
   - Mounting volume Vol-c:              [ OK ]
   - Mounting volume Vol-d:              [ OK ]
   - Mounting volume Vol-e:              [ OK ]
 * Finishing mount of volumes...                 [ OK ]
 * Generating Hosts File...                      [ OK ]
 * Configuring System Hostname...                [ OK ]
 * Configuring Samba...                                  [ OK ]
 * Configuring LAN interface...                  [ OK ]
 * Starting udevd...                                     [ OK ]
 * Starting web server...                                [ OK ]
 * Initializing Timezone...                      [ OK ]
 * Configuring Samba...                                  [ OK ]
 * Configuring System Users...
        Root password: use default password
        Set users, linux and samba accounts      [ OK ]
 * Starting syncawayd...                                 [ OK ]
 * Starting Fvdw-sl Discovery Daemon...  [ OK ]
start portmap service
starting php based setup routines step 2
 * Starting dropbear...                                  [ OK ]
 * Kill temporary dropbear...                    [ OK ]
starting php based setup routines step 3
 * Starting daemon update Hosts File...  [ OK ]
 * Starting Disk Temperature Guard...    [ OK ]
starting php based setup routines step banner


*** fvdw-sl NAS firmware
    This is fvdw-sl version: fvdw-sl 15.0
    built on: September 30 2013

    LAN IP address: 192.168.1.71 (static)

    Port configuration:

    LAN   -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
rcS finished
/bin/sh: can't access tty; job control turned off
~ #


ok full work restart and shutdown

[fvdw]

:-D finally

and do the reboot and shutdown buttons now work in the web interface

[taetae]

:-D finally

and do the reboot and shutdown buttons now work in the web interface

great job fvdw

What do you want me to do now?

[fvdw]

for the moment start using your 5big1

we will need to do some work for the leds and buttons. But the rest of the firmware now should work, so try it out and report if you find problems