Time out with telnet ? any help

[Cricrou59]

Hi Jocko, I'm using 4 WD Red of 2 To and 1 Seagate Barracuda of 1.5 To. At least I've made many tests with the disks and I must go back to zero with the NAS.
Friendly,

[fvdw]

Does the disk(s) spin up when you give "ide reset" command in uboot console?

[Cricrou59]

Hi and thanks for your help; onely the fith disk is blinking red when i'm doing the command ide reset.

[Cricrou59]

Here the report for ide reset
I've made another test and the first disk in left side is blinking red



provided by fvdw
waiting for u-boot..
starting u-boot net console click on window and press enter

Marvell>> ide reset
ide reset

Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
[0 4]: failed to perform ATA Identify command
Failed initializing storage deivce connected to SATA channel 4

Marvell>>

[Jocko]

Ok cricrou59 but do you hear if the disks are spinning ?

[Cricrou59]

Hi,

I've just wait a while to do something else and now i'v this report :
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
[0 4]: failed to perform ATA Identify command
Failed initializing storage deivce connected to SATA channel 4

Marvell>> ide reset
ide reset

Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: WDC WD20EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC
4M3DFZATE
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: WDC WD20EFRX-68EUZN0 Firm: 80.00A80 Ser#: WD-WMC
4M1213158
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 2: OK
Model: WDC WD20EFRX-68AX9N0 Firm: 80.00A80 Ser#: WD-WMC
300463460
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: WDC WD20EFRX-68AX9N0 Firm: 80.00A80 Ser#: WD-WMC
300371936
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: WDC WD20EFRX-68EUZN0 Firm: 82.00A82 Ser#: WD-WCC
4M0YT1CLR
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)

Marvell>>

[Cricrou59]

Now I'm trying to install the firmware and it's processing to work
I will tell you next and for asking you for the next step to putting the other disks in the NAS

[Cricrou59]

Re, the NAS has rebooted normally after the installation done but it's demands a login and a password, I've entered admin /admin but it doesn't work

[Cricrou59]

it's ok I've found it in the Help explanation,

What I'm supposed to do to put the other disks in the NAS ?

[Jocko]

Glad to hear you made a progress but it is really amazing this time that works :scratch

Anyhow the next step is to initialize the other disks. Now all can be done from the web-interface : go to the disk setup menu and run the initialize process on the 4 disks