Time out with telnet ? any help

[Cricrou59]

Hi all,

I'm trying to install firmware on a Lacie 5 Big Network 1 (Orion) with only left disk and I Don't manage to issue. I have read the topic about this problem "Time out" with Telnet. I've tried many ways to resolve it, but I'm having always the same issue.

I have trying with a pc with Windows XP and Avast/Firewall Windows disable and still the same.
I have a fiber box sfr with Firewall disable.
Please any help to tell me what to do ?
Thanks

[Jocko]

Hi

What kernel filename did you select ?

[Cricrou59]

UIMAGE-26394-5BIG1-45-standalone

[Jocko]

So kernel file file is ok.

Additional information about timeout issue, check if :
- ip xxx.yyy.zzz.252 is not used by a host on your LAN
- ip xxx.yyy.zzz.252 is an allowed address by your free box
- after disabling any firewall, the main thing is to have only one iface card enabled on your PC. Please to note 'to be disconnected' is not enough, you need to disable the card.

[Cricrou59]

Hi Joko,

I've tried many time to resolve the problem but it issue always the same thing time out with telnet

Antivirus Kapersky disable - one lan card enable
IP 192.168.0.252 ok on router BOX SFR
Tests done on 3 PC 1 with Windows xp, 1 with Windows 10 64 bits and the last with Windows 10 pro 64 bits

The only thing I think is that I'm running Windows 10 pro 64 bits
Every thing is doing fine till telnet

I Don't know what to do...

[Cricrou59]

The IP 192.168.0.252 is only used by the NAS, I've checked the Mac Adress

[Jocko]

Ok we will try to get a telnet access manually.

- CLose any fvdw-sl windows : fvdw-sl console; tftpd, nc
- start again fvdw-sl console
- from fvdw-sl console window, start tftp server and U-boot console
Then on nc window, you must have this message

Code: Select all

provided by fvdw
waiting for u-boot..

So start your 5big1 and wait until you get this message

Code: Select all

starting u-boot net console click on window and press enter

After pressing Enter, you should get the "Marvell" prompt

So do

Code: Select all

Marvell>> setenv ipaddr ${ipaddr}
Marvell>> setenv serverip ${serverip}
Marvell>> setenv bootargs console=ttyS0,115200 netconsole=6666@${ipaddr}/,6666@${serverip}/
Marvell>> tftpboot 0x800000 UIMAGE-26394-5BIG1-45-standalone

Then you should get this output like this

Code: Select all

Using egiga0 device
TFTP from server 192.168.1.12; our IP address is 192.168.1.252
Filename 'UIMAGE-3142-KIRKWOOD-158-standalone'.
Load address: 0x800000
Loading: #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         #################################################################
         ###########################################
done
Bytes transferred = 5876336 (59aa70 hex)

then type the command 'bootm' and you should get this new output:

Code: Select all

Marvell>> bootm
bootm
## Booting image at 00800000 ...
   Image Name:   Linux-3.14.2
   Created:      2017-03-05   0:29:58 UTC
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    5876272 Bytes =  5.6 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK

Starting kernel ...

and later some kernel messages like

Code: Select all

[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1  (GCC) ) #158 PREEMPT Sun Mar 5 01:29:06 CET 2017
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
....


wait a moment upto there is no new kernel message and from fvdw-sl console window, run 'Telnet Terminal',and then try to connect you

Please to post all output of nc window

[Jocko]

Please not to send such requests ! :disapprove

Code: Select all

85.168.90.xxx plugout.net - [09/Jun/2019:19:34:34 +0200] "GET /8C5EFD50-F1AE-7D4A-990B-45580898A489/websocket?url=https%3A%2F%2Fplugout.net%2Fviewtopic.php%3Ff%3D30%26t%3D3051&nocache=1560101681719 HTTP/1.1" 404 244 "-" "Mozilla/5.0 (Windows NT 10.0; Win64; x64) AppleWebKit/537.36 (KHTML, like Gecko) Chrome/64.0.3282.140 Safari/537.36 Edge/18.17763"

Which are useless on plugout

[Cricrou59]

Re
when i'm setting serverip i have an error !

[Cricrou59]

sorry i didn't see your last message