I’ve put in five 2TB HGST HUS724020ALA640 disks, replaced the capacitors on the motherboard, and added pins to the J29 header for accessing the serial console.
When connected to the serial console, the `ide reset` command almost always fails to initialise one or more disks. I can detect no clear pattern to the failures. The failing slots vary depending on the number of disks installed.
Any advice?
- Code: Select all
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: RD-88F5281-LaCie LE
U-Boot 1.1.4 (Jun 26 2008 - 16:55:41) Marvell version: 2.4.9
U-Boot code: 00200000 -> 0026FFF0 BSS: -> 00283280
Soc: 88F5281 D0 (DDR2)
CPU running @ 500Mhz
SysClock = 166Mhz , TClock = 166Mhz
DRAM CS[0] base 0x00000000 size 128MB
DRAM Total size 128MB 32bit width
[4096kB@ffc00000] Flash: 4 MB
Addresses 4M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (4M - 3M): Done
CPU : ARM926 (Rev 0)
Streaming disabled
VFP initialized to Run Fast Mode.
USB 0: host mode
PCI 0: PCI Express Root Complex Interface
PCI 1: PCI-X, speed = 66000000
CPU: Write allocate Disabled
Net: egiga0 [PRIME]
POWER ON
Hit any key to stop autoboot: 0
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXG6NN
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 2: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUMX1P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXG6NN
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 2: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUMX1P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXG6NN
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 4
Failed initializing storage deivce connected to SATA channel 4
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXG6NN
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 1: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXG6NN
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Device 2: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUMX1P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Found adapter at bus 1, device 7 ... Scanning channels
Device 0: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUBWBP
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Error - Failed initializing(SRST) drive on channel 1
Failed initializing storage deivce connected to SATA channel 1
Error - Failed initializing(SRST) drive on channel 2
Failed initializing storage deivce connected to SATA channel 2
Device 3: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN1134P6GXKW0N
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Device 4: OK
Model: HGST HUS724020ALA640 Firm: MF6OAC50 Ser#: PN2134P6GUKY8P
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
Marvell>>