plugout.net

Hi i try to install fvdv on my lacie 2big2 network

1) network with only pc and nas swichted off
2) pc firewall switched off
3) connection with cable
4) launch console
5) selected load stand alone kernel
6) selected 2big2 3.5.9 206
7) switch on NAS
8) start dialog box clunc open
9) complete dialog box with bad magic number
10) start telnet it goes time out ????

what can i check ????

Thanks everybody can help me

Hi

can you tell me what standalone kernel filename did you use ?

Jocko wrote:Hi

can you tell me what standalone kernel filename did you use ?

under tftp

I use both this version under tftp
2big1-47-1-1-4-standalone

Hi

So it is the issue. This standalone kernel image is for a 2big1 (2big network 1)

For a d2nw2 you have to use the kirkwood version : UIMAGE-3142-KIRKWOOD-171-standalone

Jocko wrote:Hi

So it is the issue. This standalone kernel image is for a 2big1 (2big network 1)

For a d2nw2 you have to use the kirkwood version : UIMAGE-3142-KIRKWOOD-171-standalone

now start telnet i send pwd root and password giveit2me

fvdw installer goes ok
i reboot the system with reboot -f after the system light is fixed to red (not flash)

Hi

First I did notice you wrote you have a 2big network 2 in your first post

Hi i try to install fvdv on my lacie 2big2 network

because you posted it in the d2nw2 forum. So I moved your post in the right forum.

Then maybe when you ran the install script, you select wrongly the corresponding device according with my previous post...(select choice 1 kirkwood nwsp2, D2N2,...) instead of the choice "lacie kirkwood 2big2, 5big2"... In this case the script installs a bad kernel on the system disk. So you have to repeat the install action.

Jocko wrote:Hi

First I did notice you wrote you have a 2big network 2 in your first post

Hi i try to install fvdv on my lacie 2big2 network

because you posted it in the d2nw2 forum. So I moved your post in the right forum.

Then maybe when you ran the install script, you select wrongly the corresponding device according with my previous post...(select choice 1 kirkwood nwsp2, D2N2,...) instead of the choice "lacie kirkwood 2big2, 5big2"... In this case the script installs a bad kernel on the system disk. So you have to repeat the install action.

if i understand (i repeat for more safe)

i follow this step for my lacie 2big network 2 with 2 disk (2 tb green seagate)

1) start fwdv console 6
2) action start and load
3) select for 2 big 2 network UIMAGE-3142-KIRKWOOD-171-standalone
4) start automatic process that open telnet
5) user root pwd giveit2me
6) fvdw-sl programs
7) on the program configuration wich is the choice ???

Nope as a 2big2 and a d2nw2 are kirkwood platform, they use the same kernel.

So open a telnet terminal(action Standalone kernel,load and start), and post

Code: Select all

mkdir /sda7
mount /dev/sda7 /sda7
cat /sda7/boot.log

Other way, what does it happen if you keep one disk in the left slot ?

Sorry I did see your previous post.

So on your step 7) on the program configuration which is the choice ??? you have to select the first item "install fvdw-sl firmware on a hard disk".

So later on the first dialog, you have to select the 2d item "lacie kirkwood 2big2"

Jocko wrote:Sorry I did see your previous post.

So on your step 7) on the program configuration which is the choice ??? you have to select the first item "install fvdw-sl firmware on a hard disk".

So later on the first dialog, you have to select the 2d item "lacie kirkwood 2big2"

step 7
choice 1 and then press ok
step 8
choice 2 lacie kirkwood 2big2
step 9
delete all partition reply yes
step 10
bigger then 2 tb reply no
step 11
gpt table reply yes
step 13
proceed to delete yes
step 14
blank out mbr reply auto

at end nothig goes wrong but
at reboot -f
wich is the password for admin ??