however, if it helps, these are the outputs of the two commands
- Code: Select all
[root@LaCie-5big ~]# dmseg
-sh: dmseg: command not found
[root@LaCie-5big ~]# dmesg
193, 4 ports, feat 0x5/0x1f
[ 2.400000] ata1.00: hard resetting link
[ 2.750000] ata1.01: hard resetting link
[ 3.120000] rtc-mv rtc-mv: internal RTC not ticking
[ 3.210000] md: linear personality registered for level -1
[ 3.210000] md: raid0 personality registered for level 0
[ 3.220000] md: raid1 personality registered for level 1
[ 3.220000] md: raid10 personality registered for level 10
[ 3.230000] md: raid6 personality registered for level 6
[ 3.230000] md: raid5 personality registered for level 5
[ 3.240000] md: raid4 personality registered for level 4
[ 3.240000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 3.250000] cpufreq: Setting CPU Frequency to 1200000 KHz
[ 3.250000] cpufreq: Setting PowerSaveState to off
[ 3.260000] ata1.02: hard resetting link
[ 3.260000] cpuidle: using governor ladder
[ 3.260000] cpuidle: using governor menu
[ 3.270000] Registered led device: net5big-v2:blue:power
[ 3.270000] Registered led device: net5big-v2:red:power
[ 3.280000] Registered led device: net5big-v2:blue:sata0
[ 3.290000] Registered led device: net5big-v2:red:sata0
[ 3.290000] Registered led device: net5big-v2:blue:sata1
[ 3.300000] Registered led device: net5big-v2:red:sata1
[ 3.300000] Registered led device: net5big-v2:blue:sata2
[ 3.310000] Registered led device: net5big-v2:red:sata2
[ 3.310000] Registered led device: net5big-v2:blue:sata3
[ 3.320000] Registered led device: net5big-v2:red:sata3
[ 3.320000] Registered led device: net5big-v2:blue:sata4
[ 3.330000] Registered led device: net5big-v2:red:sata4
[ 3.330000] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 3.340000] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 3.390000] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 3.430000] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 3.470000] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 3.510000] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 3.510000] TCP cubic registered
[ 3.510000] NET: Registered protocol family 17
[ 3.520000] Bridge firewalling registered
[ 3.520000] NET: Registered protocol family 5
[ 3.530000] RPC: Registered udp transport module.
[ 3.530000] RPC: Registered tcp transport module.
[ 3.540000] /home/sbs/devs/workspace/5bignetwork2_release/system/components/linux/source/drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 3.770000] ata1.03: hard resetting link
[ 4.300000] ata1.01: ATA-10: WDC WD40EFAX-68JH4N1, 83.00A83, max UDMA/133
[ 4.300000] ata1.01: 7814037168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[ 4.330000] ata1.01: configured for UDMA/133
[ 4.370000] ata1.02: ATA-9: ST4000VN000-1H4168, SC43, max UDMA/133
[ 4.370000] ata1.02: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.440000] ata1.02: configured for UDMA/133
[ 4.480000] ata1.03: ATA-9: ST4000VN000-1H4168, SC43, max UDMA/133
[ 4.480000] ata1.03: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.550000] ata1.03: configured for UDMA/133
[ 4.550000] ata1: EH complete
[ 4.550000] scsi 0:1:0:0: Direct-Access ATA WDC WD40EFAX-68J 83.0 PQ: 0 ANSI: 5
[ 4.560000] sd 0:1:0:0: [sdc] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 4.570000] sd 0:1:0:0: [sdc] 4096-byte physical blocks
[ 4.570000] sd 0:1:0:0: [sdc] Write Protect is off
[ 4.580000] sd 0:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 4.580000] sd 0:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.590000] sdc:
[ 4.590000] sd 0:1:0:0: Attached scsi generic sg0 type 0
[ 4.600000] scsi 0:2:0:0: Direct-Access ATA ST4000VN000-1H41 SC43 PQ: 0 ANSI: 5
[ 4.610000] sd 0:2:0:0: [sdb] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 4.610000] sd 0:2:0:0: [sdb] 4096-byte physical blocks
[ 4.620000] sd 0:2:0:0: [sdb] Write Protect is off
[ 4.620000] sd 0:2:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 4.620000] sd 0:2:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.630000] sdb:
[ 4.640000] sd 0:2:0:0: Attached scsi generic sg1 type 0
[ 4.640000] scsi 0:3:0:0: Direct-Access ATA ST4000VN000-1H41 SC43 PQ: 0 ANSI: 5
[ 4.650000] sdc1 sdc2 sdc3
[ 4.650000] sd 0:3:0:0: [sda] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 4.660000] sd 0:3:0:0: [sda] 4096-byte physical blocks
[ 4.670000] sd 0:3:0:0: [sda] Write Protect is off
[ 4.670000] sd 0:3:0:0: [sda] Mode Sense: 00 3a 00 00
[ 4.670000] sd 0:3:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.680000] sda:
[ 4.680000] sd 0:3:0:0: Attached scsi generic sg2 type 0
[ 4.690000] sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8 sdb9 sdb10
[ 4.700000] sd 0:1:0:0: [sdc] Attached SCSI disk
[ 4.710000] sd 0:2:0:0: [sdb] Attached SCSI disk
[ 4.740000] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9 sda10
[ 4.750000] sd 0:3:0:0: [sda] Attached SCSI disk
[ 5.200000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.200000] ata2.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[ 5.210000] ata2.00: hard resetting link
[ 5.560000] ata2.01: hard resetting link
[ 6.070000] ata2.02: hard resetting link
[ 6.580000] ata2.03: hard resetting link
[ 6.970000] ata2.01: ATA-9: ST4000VN000-1H4168, SC46, max UDMA/133
[ 6.970000] ata2.01: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.040000] ata2.01: configured for UDMA/133
[ 7.080000] ata2.02: ATA-9: ST4000VN000-1H4168, SC43, max UDMA/133
[ 7.080000] ata2.02: 7814037168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 7.150000] ata2.02: configured for UDMA/133
[ 7.150000] ata2: EH complete
[ 7.150000] scsi 1:1:0:0: Direct-Access ATA ST4000VN000-1H41 SC46 PQ: 0 ANSI: 5
[ 7.160000] sd 1:1:0:0: [sde] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 7.170000] sd 1:1:0:0: [sde] 4096-byte physical blocks
[ 7.170000] sd 1:1:0:0: [sde] Write Protect is off
[ 7.180000] sd 1:1:0:0: [sde] Mode Sense: 00 3a 00 00
[ 7.180000] sd 1:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.190000] sde:
[ 7.190000] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 7.200000] scsi 1:2:0:0: Direct-Access ATA ST4000VN000-1H41 SC43 PQ: 0 ANSI: 5
[ 7.210000] sd 1:2:0:0: [sdd] 7814037168 512-byte logical blocks: (4.00 TB/3.63 TiB)
[ 7.210000] sd 1:2:0:0: [sdd] 4096-byte physical blocks
[ 7.220000] sd 1:2:0:0: [sdd] Write Protect is off
[ 7.220000] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[ 7.220000] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 7.230000] sdd:
[ 7.240000] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 7.270000] sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10
[ 7.280000] sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd7 sdd8 sdd9 sdd10
[ 7.280000] sd 1:1:0:0: [sde] Attached SCSI disk
[ 7.290000] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 7.290000] Freeing init memory: 148K
[ 7.300000] Freeing initramfs memory: 4K
[ 9.640000] eth0: link down
[ 9.640000] eth0: started
[ 10.680000] eth0: link up, full duplex, speed 1 Gbps
[ 12.900000] md: md0 stopped.
[ 12.910000] md: bind<sda7>
[ 12.910000] raid1: raid set md0 active with 1 out of 5 mirrors
[ 12.920000] md0: detected capacity change from 0 to 16384000
[ 12.920000] md0: unknown partition table
[ 12.930000] kjournald starting. Commit interval 5 seconds
[ 12.940000] EXT3-fs: mounted filesystem with writeback data mode.
[ 14.050000] md: bind<sdb7>
[ 14.140000] RAID1 conf printout:
[ 14.140000] --- wd:1 rd:5
[ 14.140000] disk 0, wo:0, o:1, dev:sda7
[ 14.140000] disk 1, wo:1, o:1, dev:sdb7
[ 14.150000] md: recovery of RAID array md0
[ 14.150000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 14.160000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 14.170000] md: using 128k window, over a total of 16000 blocks.
[ 14.170000] md: md0: recovery done.
[ 14.260000] RAID1 conf printout:
[ 14.260000] --- wd:2 rd:5
[ 14.260000] disk 0, wo:0, o:1, dev:sda7
[ 14.260000] disk 1, wo:0, o:1, dev:sdb7
[ 14.520000] md: bind<sdd7>
[ 14.600000] RAID1 conf printout:
[ 14.600000] --- wd:2 rd:5
[ 14.600000] disk 0, wo:0, o:1, dev:sda7
[ 14.600000] disk 1, wo:0, o:1, dev:sdb7
[ 14.610000] disk 2, wo:1, o:1, dev:sdd7
[ 14.610000] md: recovery of RAID array md0
[ 14.620000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 14.620000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 14.630000] md: using 128k window, over a total of 16000 blocks.
[ 14.870000] md: bind<sde7>
[ 17.660000] md: md0: recovery done.
[ 17.820000] RAID1 conf printout:
[ 17.820000] --- wd:3 rd:5
[ 17.820000] disk 0, wo:0, o:1, dev:sda7
[ 17.820000] disk 1, wo:0, o:1, dev:sdb7
[ 17.830000] disk 2, wo:0, o:1, dev:sdd7
[ 17.910000] RAID1 conf printout:
[ 17.910000] --- wd:3 rd:5
[ 17.910000] disk 0, wo:0, o:1, dev:sda7
[ 17.910000] disk 1, wo:0, o:1, dev:sdb7
[ 17.920000] disk 2, wo:0, o:1, dev:sdd7
[ 17.920000] disk 3, wo:1, o:1, dev:sde7
[ 17.930000] md: recovery of RAID array md0
[ 17.930000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 17.940000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 17.950000] md: using 128k window, over a total of 16000 blocks.
[ 20.160000] md: md0: recovery done.
[ 20.340000] RAID1 conf printout:
[ 20.340000] --- wd:4 rd:5
[ 20.340000] disk 0, wo:0, o:1, dev:sda7
[ 20.340000] disk 1, wo:0, o:1, dev:sdb7
[ 20.350000] disk 2, wo:0, o:1, dev:sdd7
[ 20.350000] disk 3, wo:0, o:1, dev:sde7
[ 20.850000] md: md1 stopped.
[ 20.860000] md: bind<sde8>
[ 20.870000] md: bind<sdd8>
[ 20.870000] md: bind<sdb8>
[ 20.870000] md: bind<sda8>
[ 20.880000] raid1: raid set md1 active with 4 out of 5 mirrors
[ 20.880000] md1: detected capacity change from 0 to 863567872
[ 20.980000] md1: unknown partition table
[ 21.830000] md: md2 stopped.
[ 21.870000] md: bind<sde9>
[ 21.870000] md: bind<sdd9>
[ 21.880000] md: bind<sdb9>
[ 21.880000] md: bind<sda9>
[ 21.890000] raid1: raid set md2 active with 4 out of 5 mirrors
[ 21.890000] md2: detected capacity change from 0 to 896466944
[ 21.980000] md2: unknown partition table
[ 22.840000] md: md3 stopped.
[ 22.840000] md: bind<sde5>
[ 22.850000] md: bind<sdd5>
[ 22.850000] md: bind<sdb5>
[ 22.850000] md: bind<sda5>
[ 22.860000] raid1: raid set md3 active with 4 out of 5 mirrors
[ 22.870000] md3: detected capacity change from 0 to 262078464
[ 22.960000] md3: unknown partition table
[ 28.120000] kjournald starting. Commit interval 5 seconds
[ 28.120000] EXT3-fs: mounted filesystem with writeback data mode.
[ 28.170000] kjournald starting. Commit interval 5 seconds
[ 28.180000] EXT3 FS on md2, internal journal
[ 28.180000] EXT3-fs: mounted filesystem with writeback data mode.
[ 28.340000] unionfs: unionfs: new generation number 2
[ 28.390000] unionfs: unionfs: new generation number 3
[ 29.390000] Adding 255928k swap on /dev/md3. Priority:-1 extents:1 across:255928k
[ 29.770000] usbcore: registered new interface driver usbfs
[ 29.770000] usbcore: registered new interface driver hub
[ 29.770000] usbcore: registered new device driver usb
[ 29.790000] Initializing USB Mass Storage driver...
[ 29.790000] usbcore: registered new interface driver usb-storage
[ 29.790000] USB Mass Storage support registered.
[ 30.650000] udev: starting version 139
[ 32.850000] uncorrectable error :
[ 32.850000] end_request: I/O error, dev mtdblock0, sector 0
[ 32.850000] Buffer I/O error on device mtdblock0, logical block 0
[ 32.850000] uncorrectable error :
[ 32.850000] end_request: I/O error, dev mtdblock0, sector 8
[ 32.850000] Buffer I/O error on device mtdblock0, logical block 1
[ 32.850000] end_request: I/O error, dev mtdblock0, sector 16
[ 32.850000] Buffer I/O error on device mtdblock0, logical block 2
[ 32.850000] uncorrectable error :
[ 32.850000] end_request: I/O error, dev mtdblock0, sector 24
[ 32.850000] Buffer I/O error on device mtdblock0, logical block 3
[ 32.850000] uncorrectable error :
[ 32.850000] end_request: I/O error, dev mtdblock0, sector 0
[ 32.850000] Buffer I/O error on device mtdblock0, logical block 0
[ 43.470000] uncorrectable error :
[ 43.470000] end_request: I/O error, dev mtdblock0, sector 0
[ 43.640000] md: md4 stopped.
[ 43.640000] md: bind<sdc2>
[ 43.640000] md: bind<sdd2>
[ 43.640000] md: bind<sdb2>
[ 43.640000] md: bind<sde2>
[ 43.640000] md: bind<sda2>
[ 43.640000] md: kicking non-fresh sdc2 from array!
[ 43.640000] md: unbind<sdc2>
[ 43.640000] md: export_rdev(sdc2)
[ 44.050000] raid5: device sda2 operational as raid disk 0
[ 44.050000] raid5: device sde2 operational as raid disk 4
[ 44.050000] raid5: device sdb2 operational as raid disk 3
[ 44.050000] raid5: device sdd2 operational as raid disk 2
[ 44.050000] raid5: allocated 5258kB for md4
[ 44.050000] raid5: raid level 5 set md4 active with 4 out of 5 devices, algorithm 2
[ 44.050000] RAID5 conf printout:
[ 44.050000] --- rd:5 wd:4
[ 44.050000] disk 0, o:1, dev:sda2
[ 44.050000] disk 2, o:1, dev:sdd2
[ 44.050000] disk 3, o:1, dev:sdb2
[ 44.050000] disk 4, o:1, dev:sde2
[ 44.050000] md4: detected capacity change from 0 to 15994848280576
[ 44.550000] md4: unknown partition table
[ 47.970000] eth1: started
[ 60.960000] loop: module loaded
[ 65.440000] XFS mounting filesystem md4
[ 65.680000] XFS: Invalid block length (0x0) given for buffer
[ 65.680000] XFS: Log inconsistent (didn't find previous header)
[ 65.680000] XFS: empty log check failed
[ 65.680000] XFS: log mount/recovery failed: error 5
[ 65.680000] XFS: log mount failed
[ 96.600000] iSCSI Enterprise Target Software - version 1.4.19
[ 96.600000] iscsi_trgt: Registered io type fileio
[ 96.600000] iscsi_trgt: Registered io type blockio
[ 96.600000] iscsi_trgt: Registered io type nullio
[ 104.060000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 104.060000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 104.060000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 104.090000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 104.110000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[ 104.110000] usb usb1: configuration #1 chosen from 1 choice
[ 104.110000] hub 1-0:1.0: USB hub found
[ 104.110000] hub 1-0:1.0: 1 port detected
[ 104.430000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 104.580000] usb 1-1: configuration #1 chosen from 1 choice
[ 104.580000] hub 1-1:1.0: USB hub found
[ 104.590000] hub 1-1:1.0: 2 ports detected
[ 110.720000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 110.720000] NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
[ 110.720000] NFSD: starting 90-second grace period
[ 121.290000] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
[ 1149.250000] eth0: link down
[ 1152.150000] eth0: link up, full duplex, speed 1 Gbps
- Code: Select all
[root@LaCie-5big ~]# which smartctl
/usr/sbin/smartctl
In any case, I don't know if I'm using LaCie firmware or yours. is there a command to figure this out?