Well, I did this extreme step:
With the Clonezilla software, i inserted the "failed" HD and the new one in two bay of my MacPro and clone the old on the new one.
After several hours, the procedure was successful.
So put the old HD in the NAS and the NAS remains with the front light in
solid red, while it was blinking before.
Same thing with the new HD clone.
The led on the back of the NAS are all blue.
I can connect to the NAS via SSH or via Dashboard but this is the situation now.
- Code: Select all
cat /proc/mdstat
Personalities : [linear] [raid0] [raid1] [raid10] [raid6] [raid5] [raid4]
md3 : active raid1 sda5[0] sde5[1] sdc5[4] sdb5[3] sdd5[2]
255936 blocks [5/5] [UUUUU]
md2 : active raid1 sda9[0] sde9[1] sdb9[4] sdc9[3] sdd9[2]
875456 blocks [5/5] [UUUUU]
md1 : active raid1 sda8[0] sdb8[4] sdc8[3] sdd8[2] sde8[1]
843328 blocks [5/5] [UUUUU]
md0 : active raid1 sde7[4] sdd7[3] sdc7[2] sdb7[1] sda7[0]
16000 blocks [5/5] [UUUUU]
unused devices: <none>
The MD4 it's gone and RAID5 too.
this is the new output of dmesg.
- Code: Select all
[root@LaCie-5big ~]# dmesg
cross:255928k
[ 29.430000] usbcore: registered new interface driver usbfs
[ 29.430000] usbcore: registered new interface driver hub
[ 29.440000] usbcore: registered new device driver usb
[ 29.460000] Initializing USB Mass Storage driver...
[ 29.460000] usbcore: registered new interface driver usb-storage
[ 29.460000] USB Mass Storage support registered.
[ 30.410000] udev: starting version 139
[ 33.750000] uncorrectable error :
[ 33.750000] end_request: I/O error, dev mtdblock0, sector 0
[ 33.750000] Buffer I/O error on device mtdblock0, logical block 0
[ 33.750000] uncorrectable error :
[ 33.750000] end_request: I/O error, dev mtdblock0, sector 8
[ 33.750000] Buffer I/O error on device mtdblock0, logical block 1
[ 33.750000] end_request: I/O error, dev mtdblock0, sector 16
[ 33.750000] Buffer I/O error on device mtdblock0, logical block 2
[ 33.750000] uncorrectable error :
[ 33.750000] end_request: I/O error, dev mtdblock0, sector 24
[ 33.750000] Buffer I/O error on device mtdblock0, logical block 3
[ 33.750000] uncorrectable error :
[ 33.750000] end_request: I/O error, dev mtdblock0, sector 0
[ 33.750000] Buffer I/O error on device mtdblock0, logical block 0
[ 44.530000] uncorrectable error :
[ 44.530000] end_request: I/O error, dev mtdblock0, sector 0
[ 44.720000] md: md4 stopped.
[ 44.740000] md: bind<sda2>
[ 44.750000] md: bind<sdd2>
[ 44.750000] md: bind<sdb2>
[ 44.750000] md: bind<sde2>
[ 44.760000] md: bind<sdc2>
[ 44.760000] md: kicking non-fresh sda2 from array!
[ 44.760000] md: unbind<sda2>
[ 44.760000] md: export_rdev(sda2)
[ 44.780000] raid5: device sdc2 operational as raid disk 1
[ 44.780000] raid5: device sde2 operational as raid disk 4
[ 44.780000] raid5: device sdb2 operational as raid disk 3
[ 44.780000] raid5: device sdd2 operational as raid disk 2
[ 44.790000] raid5: allocated 5258kB for md4
[ 44.880000] raid5: raid level 5 set md4 active with 4 out of 5 devices, algorithm 2
[ 44.880000] RAID5 conf printout:
[ 44.880000] --- rd:5 wd:4
[ 44.880000] disk 1, o:1, dev:sdc2
[ 44.880000] disk 2, o:1, dev:sdd2
[ 44.880000] disk 3, o:1, dev:sdb2
[ 44.880000] disk 4, o:1, dev:sde2
[ 44.880000] md4: detected capacity change from 0 to 15994848280576
[ 45.210000] md4: unknown partition table
[ 49.360000] eth1: started
[ 63.220000] loop: module loaded
[ 68.270000] XFS mounting filesystem md4
[ 72.770000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 72.770000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 72.930000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 72.930000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 72.930000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 72.930000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 72.930000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 72.930000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 72.930000] ata1.01: dev err
[ 72.930000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 72.930000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 72.930000] ata1.01: status: { DRDY ERR }
[ 72.930000] ata1.01: error: { UNC }
[ 72.930000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 72.930000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 72.930000] ata1.15: hard resetting link
[ 73.440000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 73.440000] ata1.00: hard resetting link
[ 73.790000] ata1.01: hard resetting link
[ 74.300000] ata1.02: hard resetting link
[ 74.810000] ata1.03: hard resetting link
[ 75.420000] ata1.01: configured for UDMA/133
[ 75.520000] ata1.02: configured for UDMA/133
[ 75.620000] ata1.03: configured for UDMA/133
[ 75.620000] ata1: EH complete
[ 79.540000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 79.540000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 79.560000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 79.560000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 79.560000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 79.560000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 79.560000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 79.560000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 79.560000] ata1.01: dev err
[ 79.560000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 79.560000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 79.560000] ata1.01: status: { DRDY ERR }
[ 79.560000] ata1.01: error: { UNC }
[ 79.560000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 79.560000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 79.560000] ata1.15: hard resetting link
[ 80.070000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 80.070000] ata1.00: hard resetting link
[ 80.420000] ata1.01: hard resetting link
[ 80.930000] ata1.02: hard resetting link
[ 81.440000] ata1.03: hard resetting link
[ 82.050000] ata1.01: configured for UDMA/133
[ 82.150000] ata1.02: configured for UDMA/133
[ 82.250000] ata1.03: configured for UDMA/133
[ 82.250000] ata1: EH complete
[ 86.170000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 86.170000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 86.210000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 86.210000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 86.210000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 86.210000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 86.210000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 86.210000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 86.210000] ata1.01: dev err
[ 86.210000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 86.210000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 86.210000] ata1.01: status: { DRDY ERR }
[ 86.210000] ata1.01: error: { UNC }
[ 86.210000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 86.210000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 86.210000] ata1.15: hard resetting link
[ 86.720000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 86.720000] ata1.00: limiting SATA link speed to 1.5 Gbps
[ 86.720000] ata1.00: hard resetting link
[ 87.070000] ata1.01: hard resetting link
[ 87.580000] ata1.02: hard resetting link
[ 88.090000] ata1.03: hard resetting link
[ 88.700000] ata1.01: configured for UDMA/133
[ 88.800000] ata1.02: configured for UDMA/133
[ 88.900000] ata1.03: configured for UDMA/133
[ 88.900000] ata1: EH complete
[ 92.820000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 92.820000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 92.840000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 92.840000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 92.840000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 92.840000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 92.840000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 92.840000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 92.840000] ata1.01: dev err
[ 92.840000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 92.840000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 92.840000] ata1.01: status: { DRDY ERR }
[ 92.840000] ata1.01: error: { UNC }
[ 92.840000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 92.840000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 92.840000] ata1.15: hard resetting link
[ 93.350000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 93.350000] ata1.00: limiting SATA link speed to 1.5 Gbps
[ 93.350000] ata1.00: hard resetting link
[ 93.700000] ata1.01: hard resetting link
[ 94.210000] ata1.02: hard resetting link
[ 94.720000] ata1.03: hard resetting link
[ 95.330000] ata1.01: configured for UDMA/133
[ 95.430000] ata1.02: configured for UDMA/133
[ 95.530000] ata1.03: configured for UDMA/133
[ 95.530000] ata1: EH complete
[ 99.460000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 99.460000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 99.480000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 99.480000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 99.480000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 99.480000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 99.480000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 99.480000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 99.480000] ata1.01: dev err
[ 99.480000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 99.480000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 99.480000] ata1.01: status: { DRDY ERR }
[ 99.480000] ata1.01: error: { UNC }
[ 99.480000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 99.480000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 99.480000] ata1.15: hard resetting link
[ 99.990000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 99.990000] ata1.00: limiting SATA link speed to 1.5 Gbps
[ 99.990000] ata1.00: hard resetting link
[ 100.340000] ata1.01: hard resetting link
[ 100.850000] ata1.02: hard resetting link
[ 101.360000] ata1.03: hard resetting link
[ 101.970000] ata1.01: configured for UDMA/133
[ 102.070000] ata1.02: configured for UDMA/133
[ 102.170000] ata1.03: configured for UDMA/133
[ 102.170000] ata1: EH complete
[ 106.090000] ata1: mv_handle_fbs_ncq_dev_err: pmp_map=0002 qc_map=0001 failed_links=1 nr_active_links=1
[ 106.090000] ata1: mv_handle_fbs_ncq_dev_err: done
[ 106.110000] ata1.00: failed to read SCR 1 (Emask=0x40)
[ 106.110000] ata1.01: failed to read SCR 1 (Emask=0x40)
[ 106.110000] ata1.02: failed to read SCR 1 (Emask=0x40)
[ 106.110000] ata1.03: failed to read SCR 1 (Emask=0x40)
[ 106.110000] ata1.00: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 106.110000] ata1.01: exception Emask 0x100 SAct 0x1 SErr 0x0 action 0x6 frozen
[ 106.110000] ata1.01: dev err
[ 106.110000] ata1.01: cmd 60/08:00:18:e4:3f/00:00:10:00:00/40 tag 0 ncq 4096 in
[ 106.110000] res 41/40:08:18:e4:3f/07:00:10:00:00/00 Emask 0x409 (media error) <F>
[ 106.110000] ata1.01: status: { DRDY ERR }
[ 106.110000] ata1.01: error: { UNC }
[ 106.110000] ata1.02: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 106.110000] ata1.03: exception Emask 0x100 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 106.110000] ata1.15: hard resetting link
[ 106.620000] ata1.15: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 106.620000] ata1.00: limiting SATA link speed to 1.5 Gbps
[ 106.620000] ata1.00: hard resetting link
[ 106.970000] ata1.01: hard resetting link
[ 107.480000] ata1.02: hard resetting link
[ 107.990000] ata1.03: hard resetting link
[ 108.600000] ata1.01: configured for UDMA/133
[ 108.700000] ata1.02: configured for UDMA/133
[ 108.800000] ata1.03: configured for UDMA/133
[ 108.800000] sd 0:1:0:0: [sdc] Unhandled sense code
[ 108.800000] sd 0:1:0:0: [sdc] Result: hostbyte=0x00 driverbyte=0x08
[ 108.800000] sd 0:1:0:0: [sdc] Sense Key : 0x3 [current] [descriptor]
[ 108.800000] Descriptor sense data with sense descriptors (in hex):
[ 108.800000] 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00
[ 108.800000] 10 3f e4 18
[ 108.800000] sd 0:1:0:0: [sdc] ASC=0x11 ASCQ=0x4
[ 108.800000] end_request: I/O error, dev sdc, sector 272622616
[ 108.800000] raid5:md4: read error not correctable (sector 268573720 on sdc2).
[ 108.800000] raid5: Disk failure on sdc2, disabling device.
[ 108.800000] raid5: Operation continuing on 3 devices.
[ 108.800000] ata1: EH complete
[ 108.960000] RAID5 conf printout:
[ 108.960000] --- rd:5 wd:3
[ 108.960000] disk 1, o:0, dev:sdc2
[ 108.960000] disk 2, o:1, dev:sdd2
[ 108.960000] disk 3, o:1, dev:sdb2
[ 108.960000] disk 4, o:1, dev:sde2
[ 108.960000] RAID5 conf printout:
[ 108.960000] --- rd:5 wd:3
[ 108.960000] disk 2, o:1, dev:sdd2
[ 108.960000] disk 3, o:1, dev:sdb2
[ 108.960000] disk 4, o:1, dev:sde2
[ 108.960000] I/O error in filesystem ("md4") meta-data dev md4 block 0x4008711f ("xlog_bread") error 5 buf count 512
[ 108.960000] XFS: empty log check failed
[ 108.960000] XFS: log mount/recovery failed: error 5
[ 108.960000] XFS: log mount failed
[ 124.500000] md: md4 stopped.
[ 124.500000] md: unbind<sdc2>
[ 124.500000] md: export_rdev(sdc2)
[ 124.500000] md: unbind<sde2>
[ 124.500000] md: export_rdev(sde2)
[ 124.500000] md: unbind<sdb2>
[ 124.500000] md: export_rdev(sdb2)
[ 124.500000] md: unbind<sdd2>
[ 124.500000] md: export_rdev(sdd2)
[ 124.520000] md4: detected capacity change from 15994848280576 to 0
[ 149.300000] iSCSI Enterprise Target Software - version 1.4.19
[ 149.300000] iscsi_trgt: Registered io type fileio
[ 149.300000] iscsi_trgt: Registered io type blockio
[ 149.300000] iscsi_trgt: Registered io type nullio
[ 153.480000] md: md2: recovery done.
[ 153.490000] md: recovery of RAID array md3
[ 153.490000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 153.490000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 153.490000] md: using 128k window, over a total of 255936 blocks.
[ 153.720000] RAID1 conf printout:
[ 153.720000] --- wd:5 rd:5
[ 153.720000] disk 0, wo:0, o:1, dev:sda9
[ 153.720000] disk 1, wo:0, o:1, dev:sde9
[ 153.720000] disk 2, wo:0, o:1, dev:sdd9
[ 153.720000] disk 3, wo:0, o:1, dev:sdc9
[ 153.720000] disk 4, wo:0, o:1, dev:sdb9
[ 157.660000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 157.660000] ehci_marvell ehci_marvell.70059: Marvell Orion EHCI
[ 157.660000] ehci_marvell ehci_marvell.70059: new USB bus registered, assigned bus number 1
[ 157.690000] ehci_marvell ehci_marvell.70059: irq 19, io base 0xf1050100
[ 157.710000] ehci_marvell ehci_marvell.70059: USB 2.0 started, EHCI 1.00
[ 157.710000] usb usb1: configuration #1 chosen from 1 choice
[ 157.710000] hub 1-0:1.0: USB hub found
[ 157.710000] hub 1-0:1.0: 1 port detected
[ 158.030000] usb 1-1: new high speed USB device using ehci_marvell and address 2
[ 158.180000] usb 1-1: configuration #1 chosen from 1 choice
[ 158.180000] hub 1-1:1.0: USB hub found
[ 158.190000] hub 1-1:1.0: 2 ports detected
[ 162.780000] md: md3: recovery done.
[ 162.940000] RAID1 conf printout:
[ 162.940000] --- wd:5 rd:5
[ 162.940000] disk 0, wo:0, o:1, dev:sda5
[ 162.940000] disk 1, wo:0, o:1, dev:sde5
[ 162.940000] disk 2, wo:0, o:1, dev:sdd5
[ 162.940000] disk 3, wo:0, o:1, dev:sdb5
[ 162.940000] disk 4, wo:0, o:1, dev:sdc5
[ 165.120000] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[ 165.120000] NFSD: unable to find recovery directory /var/lib/nfs/v4recovery
[ 165.120000] NFSD: starting 90-second grace period
[ 175.320000] warning: `proftpd' uses 32-bit capabilities (legacy support in use)
I don't take any further action to avoid making things worse and I'm staying with the hope of your help, maybe try to rebuild the array?