no ip address, unable to access the NAS

[fvdw]

Could be a power supply issue, if the power supply is not strong enough to start the disk then the board will see it as power failure and reboot.
You could try to see if standalone kernel loads without any disk installed. On the serial interface you can see what is happening . The standalone kernel runs from ram so even without any disk installed.

That you cannot stop boot us because waiting time is set to zero.

[danilomag]

The strange thing is that the system only reboots when there is no disk connected. When I connect the disks, the whole kernel is loaded and the system does not reboot.

[fvdw]

What is the output in the serial interface with disk connected?

[danilomag]

the output is the same whether i connect one drive or if i connect all five

Code: Select all

          | |    __ _ / ___(_) ___
          | |   / _` | |   | |/ _ \
          | |___ (_| | |___| |  __/
          |_____\__,_|\____|_|\___|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: 5BIG REV: 2 LE
Hold front button - long :  FAIL


U-Boot 1.1.4 (Sep  8 2011 - 17:27:17) Marvell version: 3.4.16  LaCie 1.5.23

U-Boot code: 06000000 -> 0607FFF0  BSS: -> 060CE600

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM CAS Latency = 6 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Flash:  0 kB
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
Port Multiplier found @ 0 1. Vendor: 11ab ports: 4
[0 1 1]: Enable DMA mode
  Device 5 @ 0 1 1:
Model: ST3000DM001-1ER166                       Firm: CC45     Ser#:             W500AWN2
            Type: Hard Disk
dev_desc->blksz = 512
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)
[0 1 2]: Enable DMA mode
  Device 6 @ 0 1 2:
Model: ST3000DM001-1ER166                       Firm: CC45     Ser#:             W500EZK0
            Type: Hard Disk
dev_desc->blksz = 512
            Supports 48-bit addressing
            Capacity: 2861588.4 MB = 2794.5 GB (5860533168 x 512)


** Device 3 not available

** Device 2 not available

** Device 1 not available
## Valid EFI partition found ##

Loading from IDE device 6, partition 10: Name: gpt10
  Type: U-Boot
   Image Name:   Linux kernel-2.6.31.14-svn6790 [
   Created:      2015-05-29  20:48:14 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    5548395 Bytes =  5.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
   Image 0:  3003932 Bytes =  2.9 MB
   Image 1:  2544451 Bytes =  2.4 MB
## Booting image at 00800000 ...
   Image Name:   Linux kernel-2.6.31.14-svn6790 [
   Created:      2015-05-29  20:48:14 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    5548395 Bytes =  5.3 MB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
   Image 0:  3003932 Bytes =  2.9 MB
   Image 1:  2544451 Bytes =  2.4 MB
   Verifying Checksum ... OK
OK
bootargs from environment variables : console=ttyS0,115200 root=/dev/sdd7 ro reset=0 productType=BIG5_KW cap=gpt,lba64

Starting kernel ...

Uncompressing Linux................................................................................................................................................................................................. done, booting the kernel.
[    0.000000] Linux version 2.6.31.14-svn6790 (sbs@node2.lacie.com) (gcc version 4.2.1) #1 Fri May 29 20:06:41 UTC 2015
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: net5big_nand_v2
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sdd7 ro reset=0 productType=BIG5_KW cap=gpt,lba64
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 510592KB available (5420K code, 377K data, 148K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] xor: measuring software checksum speed
[    0.280000]    arm4regs  :  1089.600 MB/sec
[    0.330000]    8regs     :   826.800 MB/sec
[    0.380000]    32regs    :   927.200 MB/sec
[    0.380000] xor: using function: arm4regs (1089.600 MB/sec)
[    0.380000] NET: Registered protocol family 16
[    0.380000] Feroceon L2: Enabling L2
[    0.380000] Feroceon L2: Cache support initialised.
[    0.380000]
[    0.380000] CPU Interface
[    0.380000] -------------
[    0.380000] SDRAM_CS0 ....base 00000000, size 256MB
[    0.380000] SDRAM_CS1 ....base 10000000, size 256MB
[    0.380000] SDRAM_CS2 ....disable
[    0.380000] SDRAM_CS3 ....disable
[    0.380000] PEX0_MEM ....base e8000000, size 128MB
[    0.380000] PEX0_IO ....base f2000000, size   1MB
[    0.380000] INTER_REGS ....base f1000000, size   1MB
[    0.380000] NFLASH_CS ....base fa000000, size   2MB
[    0.380000] SPI_CS ....base f4000000, size  16MB
[    0.380000] BOOT_ROM_CS ....no such
[    0.380000] DEV_BOOTCS ....no such
[    0.380000] CRYPT_ENG ....base f0000000, size   2MB
[    0.380000]
[    0.380000]   Marvell Development Board (LSP Version KW_LSP_5.0.3)-- net5big_v2  Soc: 88F6281 A1 LE
[    0.380000]
[    0.380000]  Detected Tclk 166666667 and SysClk 400000000
[    0.380000] Register Marvell USB EHCI Host controller #0
[    0.390000] bio: create slab <bio-0> at 0
[    0.390000] SCSI Scattered Spinup: Enabled
[    0.390000]   o Maximum Disk Spinup: 1
[    0.390000]   o Disk Spinup timeout: 10
[    0.390000] SCSI subsystem initialized
[    0.560000] raid6: int32x1     91 MB/s
[    0.730000] raid6: int32x2    107 MB/s
[    0.900000] raid6: int32x4    123 MB/s
[    1.070000] raid6: int32x8    108 MB/s
[    1.070000] raid6: using algorithm int32x4 (123 MB/s)
[    1.070000] NET: Registered protocol family 2
[    1.070000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    1.070000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.070000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    1.070000] TCP: Hash tables configured (established 16384 bind 16384)
[    1.070000] TCP reno registered
[    1.070000] NET: Registered protocol family 1
[    1.070000] Trying to unpack rootfs image as initramfs...
[    1.080000] Switched to NOHz mode on CPU #0
[    1.230000] Freeing initrd memory: 2484K
[    1.230000] cpufreq: Init kirkwood cpufreq driver
[    1.250000] cesadev_init(c000ee90)
[    1.250000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    1.250000] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
[    1.250000] gpio-usb gpio-usb: USB GPIO's initialized
[    1.250000] g762 0-003e: found a platform specific fan speed array
[    1.250000] g762 0-003e: device successfully initialized
[    1.250000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.250000] Registering unionfs 2.5.10 (for 2.6.31.14)
[    1.250000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.250000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.260000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    1.260000] SGI XFS Quota Management subsystem
[    1.260000] msgmni has been set to 1002
[    1.260000] alg: No test for cipher_null (cipher_null-generic)
[    1.260000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    1.260000] alg: No test for digest_null (digest_null-generic)
[    1.260000] alg: No test for compress_null (compress_null-generic)
[    1.260000] alg: No test for stdrng (krng)
[    1.270000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    1.270000] async_tx: api initialized (async)
[    1.270000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.270000] io scheduler noop registered
[    1.270000] io scheduler anticipatory registered (default)
[    1.270000] io scheduler deadline registered
[    1.270000] io scheduler cfq registered
[    1.290000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.290000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    1.290000] console [ttyS0] enabled
[    1.780000] brd: module loaded
[    1.780000] at24 0-0050: 512 byte 24c04 EEPROM (writable)
[    1.780000] sata_mv sata_mv.0: version 1.28
[    1.790000] sata_mv sata_mv.0: slots 32 ports 2
[    1.790000] scsi0 : sata_mv
[    1.800000] scsi1 : sata_mv
[    1.800000] ata1: SATA max UDMA/133 irq 21
[    1.800000] ata2: SATA max UDMA/133 irq 21
[    1.810000] INIT Marvell Ethernet Driver: mv_netdev
[    1.810000] Loading Marvell Ethernet Driver:
[    1.820000]   o Cached descriptors in DRAM
[    1.820000]   o DRAM SW cache-coherency
[    1.830000]   o 2 Giga ports supported
[    1.830000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    1.840000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    1.840000]   o TCP segmentation offload (TSO) supported
[    1.850000]   o Large Receive offload (LRO) supported
[    1.850000]   o Receive checksum offload supported
[    1.860000]   o Transmit checksum offload supported
[    1.860000]   o Network Fast Processing (Routing) supported - (Disabled)
[    1.870000]   o Proc tool API enabled
[    1.870000]   o SKB Reuse supported - (Disabled)
[    1.880000]   o SKB Recycle supported - (Disabled)
[    1.880000]   o Rx descripors: q0=128
[    1.880000]   o Tx descripors: q0=532
[    1.890000]   o Loading network interface(s):
[    1.890000]     o  register under mv_netdev platform
[    1.900000]     o eth0, ifindex = 2, GbE port = 0
[    1.900000]     o eth1, ifindex = 3, GbE port = 1
[    1.910000]
[    1.910000] mvFpRuleDb (dffec000): 4096 entries, 16384 bytes
[    1.920000] console [netcon0] enabled
[    1.920000] netconsole: network logging started
[    1.930000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
[    1.930000] Scanning device for bad blocks
[    2.070000] Creating 3 MTD partitions on "orion_nand":
[    2.070000] 0x000000000000-0x000000100000 : "u-boot"
[    2.080000] 0x000000100000-0x000001100000 : "uImage"
[    2.090000] 0x000001100000-0x000010000000 : "root"
[    2.090000] mice: PS/2 mouse device common for all mice
[    2.100000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    2.110000] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[    2.200000] md: linear personality registered for level -1
[    2.200000] md: raid0 personality registered for level 0
[    2.210000] md: raid1 personality registered for level 1
[    2.210000] md: raid10 personality registered for level 10
[    2.220000] md: raid6 personality registered for level 6
[    2.220000] md: raid5 personality registered for level 5
[    2.230000] md: raid4 personality registered for level 4
[    2.230000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.250000] cpuidle: using governor ladder
[    2.250000] cpuidle: using governor menu
[    2.250000] Registered led device: net5big-v2:blue:power
[    2.260000] Registered led device: net5big-v2:red:power
[    2.260000] Registered led device: net5big-v2:blue:sata0
[    2.270000] Registered led device: net5big-v2:red:sata0
[    2.280000] Registered led device: net5big-v2:blue:sata1
[    2.280000] Registered led device: net5big-v2:red:sata1
[    2.290000] Registered led device: net5big-v2:blue:sata2
[    2.290000] Registered led device: net5big-v2:red:sata2
[    2.300000] Registered led device: net5big-v2:blue:sata3
[    2.300000] Registered led device: net5big-v2:red:sata3
[    2.310000] Registered led device: net5big-v2:blue:sata4
[    2.310000] Registered led device: net5big-v2:red:sata4
[    2.320000] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[    2.330000] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[    2.370000] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    2.390000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    2.390000] ata1.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    2.400000] ata1.00: hard resetting link
[    2.420000] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[    2.460000] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[    2.500000] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[    2.500000] TCP cubic registered
[    2.500000] NET: Registered protocol family 17
[    2.510000] Bridge firewalling registered
[    2.510000] NET: Registered protocol family 5
[    2.520000] RPC: Registered udp transport module.
[    2.520000] RPC: Registered tcp transport module.
[    2.530000] rtc-mv rtc-mv: setting system clock to 2021-07-26 04:11:28 UTC (1627272688)
[    2.750000] ata1.01: hard resetting link
[    3.100000] ata1.02: hard resetting link
[    3.450000] ata1.03: hard resetting link
[    3.800000] ata1: EH complete
[    4.310000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    4.310000] ata2.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    4.320000] ata2.00: hard resetting link
[    4.670000] ata2.01: hard resetting link
[    5.180000] ata2.02: hard resetting link
[    5.690000] ata2.03: hard resetting link
[    6.080000] ata2.01: ATA-9: ST3000DM001-1ER166, CC45, max UDMA/133
[    6.080000] ata2.01: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    6.150000] ata2.01: configured for UDMA/133
[    6.190000] ata2.02: ATA-9: ST3000DM001-1ER166, CC45, max UDMA/133
[    6.190000] ata2.02: 5860533168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[    6.260000] ata2.02: configured for UDMA/133
[    6.260000] ata2: EH complete
[    6.260000] scsi 1:1:0:0: Direct-Access     ATA      ST3000DM001-1ER1 CC45 PQ: 0 ANSI: 5
[    6.270000] sd 1:1:0:0: [sde] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[    6.280000] sd 1:1:0:0: [sde] 4096-byte physical blocks
[    6.280000] sd 1:1:0:0: [sde] Write Protect is off
[    6.290000] sd 1:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.300000]  sde:
[    6.300000] sd 1:1:0:0: Attached scsi generic sg0 type 0
[    6.310000] scsi 1:2:0:0: Direct-Access     ATA      ST3000DM001-1ER1 CC45 PQ: 0 ANSI: 5
[    6.320000] sd 1:2:0:0: [sdd] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB)
[    6.320000] sd 1:2:0:0: [sdd] 4096-byte physical blocks
[    6.330000] sd 1:2:0:0: [sdd] Write Protect is off
[    6.330000] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    6.340000]  sdd:
[    6.350000] sd 1:2:0:0: Attached scsi generic sg1 type 0
[    6.370000]  sde1 sde2 sde3 sde4 sde5 sde6 sde7 sde8 sde9 sde10
[    6.380000] sd 1:1:0:0: [sde] Attached SCSI disk
[    6.400000]  sdd1 sdd2 sdd3 sdd4 sdd5 sdd6 sdd7 sdd8 sdd9 sdd10
[    6.400000] sd 1:2:0:0: [sdd] Attached SCSI disk
[    6.410000] Freeing init memory: 148K
[    6.410000] Freeing initramfs memory: 4K
===INITRAMFS: =======================================INITRAMFS================================
===INITRAMFS: Initializing filesystem
===INITRAMFS: Mounting /proc
===INITRAMFS: Mounting /sys
===INITRAMFS: Populating /dev
===INITRAMFS: Mounting /dev/pts
===INITRAMFS: Product ID = 'net5big_nand_v2'
===INITRAMFS: numRaidDevices=2
[    8.680000] eth0: link down
[    8.680000] eth0: started
Sleep mode disabled
Set led mode: off
Set led mode: startup
[   10.300000] eth0: link up, full duplex, speed 1 Gbps
kill: cannot kill pid 669: No such process
===INITRAMFS: Found available BootFS partition: /dev/sdd7
===INITRAMFS: Normal boot, starting bootfs system array
===INITRAMFS: Starting bootfs RAID array (/dev/md0) with /dev/sdd7
[   11.970000] md: md0 stopped.
[   11.970000] md: bind<sdd7>
[   11.980000] raid1: raid set md0 active with 1 out of 5 mirrors
[   11.980000] md0: detected capacity change from 0 to 16384000
===INITRAMFS: Mouting /dev/md0 o[   11.990000]  md0:n /root read onl unknown partition table
y
[   12.000000] kjournald starting.  Commit interval 5 seconds
[   12.000000] EXT3-fs: mounted filesystem with writeback data mode.
===INITRAMFS: Switching to bootfs, leaving initramfs
===BOOTFS: =======================================BOOTFS=================================
===BOOTFS: Initializing filesystem
===BOOTFS: Mounting /proc
mount: /etc/mtab: Read-only file system
===BOOTFS: Mounting /sys
mount: /etc/mtab: Read-only file system
===BOOTFS: Populating /dev
===BOOTFS: Mounting /dev/pts
mount: /etc/mtab: Read-only file system
===BOOTFS: Mounting /dev/shm
mount: /etc/mtab: Read-only file system
===BOOTFS: Warning: addBootfsComponents() /dev/sdd7 is already part of /dev/md0, won't add it
===BOOTFS: addBootfsComponents() Adding /dev/sde7 to /dev/md0
[   13.080000] md: bind<sde7>
[   13.180000] RAID1 conf printout:
[   13.180000]  --- wd:1 rd:5
[   13.180000]  disk 0, wo:1, o:1, dev:sde7
[   13.180000]  disk 2, wo:0, o:1, dev:sdd7
[   13.190000] md: recovery of RAID array md0
[   13.190000] md: minimum _guaranteed_  speed: 1000 KB/sec/disk.
[   13.200000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[   13.210000] md: using 128k window, over a total of 16000 blocks.
[   13.210000] md: md0: recovery done.
===BOOTFS: Synchronizing /dev/md0
[   13.360000] RAID1 conf printout:
[   13.360000]  --- wd:2 rd:5
[   13.360000]  disk 0, wo:0, o:1, dev:sde7
[   13.360000]  disk 2, wo:0, o:1, dev:sdd7
===BOOTFS: Starting md1 (RootFS)
[   13.820000] md: md1 stopped.
[   13.830000] md: bind<sde8>
[   13.830000] md: bind<sdd8>
[   13.840000] raid1: raid set md1 active with 2 out of 5 mirrors
[   13.850000] md1: detected capacity change from 0 to 863567872
[   13.920000]  md1: unknown partition table
===BOOTFS: Starting md2 (Snapshots)
[   14.550000] md: md2 stopped.
[   14.560000] md: bind<sde9>
[   14.560000] md: bind<sdd9>
[   14.570000] raid1: md2 is not clean -- starting background reconstruction
[   14.580000] raid1: raid set md2 active with 2 out of 5 mirrors
[   14.580000] md2: detected capacity change from 0 to 896466944
[   14.590000] md: resync of RAID array md2
[   14.590000] md: minimum _guaranteed_  speed: 1000 KB/sec/disk.
[   14.600000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[   14.610000] md: using 128k window, over a total of 875456 blocks.
[   14.670000]  md2: unknown partition table
===BOOTFS: Starting md3 (Swap)
[   15.630000] md: md3 stopped.
[   15.650000] md: bind<sdd5>
[   15.660000] md: bind<sde5>
[   15.660000] raid1: raid set md3 active with 2 out of 5 mirrors
[   15.670000] md3: detected capacity change from 0 to 262078464
[   15.740000]  md3: unknown partition table
===BOOTFS: #### Running File System Check on Snapshot Partition (/dev/md2) ###
e2fsck 1.37 (21-Mar-2005)
/dev/md2: recovering journal
/dev/md2: clean, 31535/109536 files, 124045/218864 blocks (check after next mount)
#### Starting PatchManager using /dev/md1 and /dev/md2  ####
[   16.340000] kjournald starting.  Commit interval 5 seconds
[   16.340000] EXT3-fs: mounted filesystem with writeback data mode.
[   16.360000] kjournald starting.  Commit interval 5 seconds
[   16.360000] EXT3 FS on md2, internal journal
[   16.370000] EXT3-fs: mounted filesystem with writeback data mode.
===BOOTFS: Creating base union /var/base from /var/original
===BOOTFS: Loading snapshots from /snapshots/snaps
[   16.510000] unionfs: unionfs: new generation number 2
mount: /etc/mtab: Read-only file system
[   16.560000] unionfs: unionfs: new generation number 3
mount: /etc/mtab: Read-only file system

        Next Generation Init version ( 0.6.10.2 Die bugs die! )
        http://www.initng.org
        Author: Jimmy Wennlund <jimmy.wennlund@gmail.com>
        If you find initng useful, please consider a small donation.

        System is starting up!

      runlevel/default                  [starting]
      initial                           [starting]
      dbus                              [starting]
      dbus/uuidgen                      [starting]
      udev/filldev                      [starting]
      udev/udevd                        [starting]
      udev/mountdev                     [starting]
      udev/set_hotplug                  [starting]
      hald                              [starting]
      dhcdbd                            [starting]
      bonding                           [starting]
      klogd                             [starting]
      syslogd                           [starting]
      logrotate                         [starting]
      raid                              [starting]
      usb                               [starting]
      NetworkManager                    [starting]
      NetworkManager/prepare            [starting]
      http                              [starting]
      getty/1                           [starting]
      sshd/generate_keys                [starting]
      cron                              [starting]
      unicorn                           [starting]
      lvm                               [starting]
      thumbd                            [starting]

 initial start:
  load RTC  date: Mon Jul 26 04:11:43 UTC 2021
  save file date: Mon Jul 26 04:11:43 UTC 2021

   3% initial                           [done]          ( done in 1022ms )
  14% dbus/uuidgen                      [done]          ( done in 79ms )
  14% udev/mountdev                     [done]          ( done in 78ms )
  14% NetworkManager/prepare            [done]          ( done in 77ms )
  17% thumbd                            [started]       ( pid: 1509 )
  21% cron                              [started]       ( pid: 1511 )
  25% dbus                              [started]       ( pid: 1512 )
  28% udev/udevd                        [started]       ( pid: 1515 )
  32% udev/set_hotplug                  [done]          ( done in 57ms )
udevd-event[1569]: error changing netif name eth0 to eth1: Device or resource busy

  35% udev/filldev                      [done]          ( done in 4995ms )
  46% hald                              [started]       ( pid: 2164 )
  46% getty/1                           [started]       ( pid: 2169 )
  50% sshd/generate_keys                [done]          ( done in 120ms )
  53% usb                               [done]          ( done in 141ms )
  57% logrotate                         [done]          ( done in 6505ms )
  60% syslogd                           [started]       ( pid: 2186 )
  67% klogd                             [started]       ( pid: 2187 )
  71% bonding                           [done]          ( done in 31ms )
  75% dhcdbd                            [started]       ( pid: 2190 )

LaCix Linux release 2.2.12.2
Kernel 2.6.31.14-svn6790 on an armv5tel / ttyS0
LaCie-5big login:   78% NetworkManager  [started]       ( pid: 2193 )
  85% http                              [started]       ( pid: 2194 )
  89% raid                              [done]          ( done in 3654ms )
  93% lvm                               [done]          ( done in 774ms )
 100% unicorn                           [started]       ( pid: 2285 )


        runlevel "runlevel/default" up in, 9986ms.

      runlevel/default                  [done]          ( done in 10917ms )
ifconfig
Password:       fan_controller          [starting]
      fan_controller                    [started]       ( pid: 2341 )
      mdadm                             [starting]
      mdadm                             [done]          ( done in 24ms )
      avahi                             [starting]
      avahi                             [started]       ( pid: 2470 )
      ipcommd                           [starting]
      ipcommd                           [started]       ( pid: 2490 )
      samba/smbd                        [starting]
      samba/initial                     [starting]
      samba/initial                     [done]          ( done in 61ms )
      samba/smbd                        [started]       ( pid: 2536 )
      samba/nmbd                        [starting]
      samba/nmbd                        [started]       ( pid: 2539 )
      samba/winbind                     [starting]
      samba/winbind                     [started]       ( pid: 2543 )
      cups                              [starting]
      cups                              [started]       ( pid: 2549 )

Login timed out       getty/1           [starting]
      getty/1                           [starting]
      getty/1                           [started]       ( pid: 2663 )

LaCix Linux release 2.2.12.2
Kernel 2.6.31.14-svn6790 on an armv5tel / ttyS0
LaCie-5big login:       iscsitarget     [starting]
      iscsitarget/system                [starting]
      iscsitarget/system                [done]          ( done in 133ms )
      iscsitarget                       [started]       ( pid: 2802 )

 iscsitarget daemon:
  1627272787.676737: unable to create server socket (Address family not supported by protocol) 10 1 6!



[fvdw]

Note, that the system reboots when no disk is installed could be because the lacie firmware in nand is designed to install firmware on a empty disk. If it doesn't find a disk I can imagine that it reset the nas.

The output with disks shows that now the firmware is loaded from disk and the system starts. What I don't see is if the network interface comes up.

When the system has booted and you press enter on serial console, do you get a command prompt? If so give the command

Code: Select all

ifconfig

And post output

[danilomag]

I already tried with ifconfig, but I can't get an output! this is because it asks me to enter login and password to access the shell.
but if I insert a formatted disk? could anything change?

[fvdw]

I see, no putting in an formatted or unformatted disk without lacie firmware will cause the nand lacie firmware being loaded which will then initialize the disk and copy firmware to it.

Do you a pc running linux?

[fvdw]

Another question, can you connect to the lacie webinterface when lacie firmware is loaded from disk. Ip could be retrieved from router client list or using lacie assistant that runs under windows

[danilomag]

yes, I have some linux virtual machines available

[danilomag]

In no case can I connect to the web interface. With the disks disconnected, I find the IP address of the Nas in the devices connected to the modem. With Disk, nas is not detected by the modem.I have not downloaded lacie assistant