no ip address, unable to access the NAS

[fvdw]

uboot sets manually an ip address. The fact that window changes after waiting for uboot with message starting uboot console press enter proves that the pc has had contact with the nas and received output.
When pressing enter a command is sent to the nas using a tool called nc to enter interactive mode. It seems the commands form nc are not reaching your nas.

Do you have more network cards in your PC? For example a cable connection and wireless.
If so disable the wireless adapter

[danilomag]

I've tried so many times, but nothing changes. Is there a way to access u-boot via serial cable? in this way, I could set an IP to the NAS and upload everything.
some time ago I had done the reset as described on the Lacie website, but even that didn't seem to work

[fvdw]

Yes there is serial port but you will need to disassemble the nas to get to it.

The 5big2 has two lan ports, did you use lan1?

[danilomag]

disassembling the nas is not a problem, i have already changed the capacitors.
I tested with both LAN ports

[fvdw]

You will need a 232 ttl cable 3.3 Volt. There are usb to 232 ttl cables on the market be sure to use one that uses 3.3V on nas side as 5V will damage your mainboard.

I need to check my archive how to connect

[fvdw]

yellow = pin 8 is tx
black = pin 7 is rx
white = pin 2 is gnd

(red = pin1 is supplying 3.3v , only needed when your adapter needs 3.3 v. Normally usb tot 3.3 ttl cable do not use this cable, they use an internal volatage convertor to make 3.3 v from 5 V usb)

[danilomag]

This is the first time that an ip address has been assigned to the nas 192.168.1.112
There seems to be something wrong, after it starts booting it restarts itself

Code: Select all

          | |    __ _ / ___(_) ___
          | |   / _` | |   | |/ _ \
          | |___ (_| | |___| |  __/
          |_____\__,_|\____|_|\___|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|
 ** MARVELL BOARD: 5BIG REV: 2 LE
Hold front button - long :  FAIL


U-Boot 1.1.4 (Sep  8 2011 - 17:27:17) Marvell version: 3.4.16  LaCie 1.5.23

U-Boot code: 06000000 -> 0607FFF0  BSS: -> 060CE600

Soc: MV88F6281 Rev 3 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 166Mhz

DRAM CAS Latency = 6 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Flash:  0 kB
Addresses 98M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (98M - 97M): Done
NAND:256 MB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled

Module 0 is RGMII

USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
egiga0 no link
egiga1 no link
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot:  0

Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
Port Multiplier found @ 0 1. Vendor: 11ab ports: 4


** Device 3 not available

** Device 2 not available

** Device 1 not available

** Device 6 not available

** Device 5 not available

** Device 3 not available

** Device 2 not available

** Device 1 not available

** Device 6 not available

** Device 5 not available

Loading from NAND 256MB 3,3V 8-bit, offset 0x100000
   Image Name:   Capsule [2.6.31.14-svn6790]
   Created:      2011-12-12  17:46:06 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    7510357 Bytes =  7.2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
   Image 0:  3003720 Bytes =  2.9 MB
   Image 1:  4506625 Bytes =  4.3 MB
## Booting image at 00800000 ...
   Image Name:   Capsule [2.6.31.14-svn6790]
   Created:      2011-12-12  17:46:06 UTC
   Image Type:   ARM Linux Multi-File Image (uncompressed)
   Data Size:    7510357 Bytes =  7.2 MB
   Load Address: 00008000
   Entry Point:  00008000
   Contents:
   Image 0:  3003720 Bytes =  2.9 MB
   Image 1:  4506625 Bytes =  4.3 MB
   Verifying Checksum ... OK
OK
bootargs from environment variables : console=ttyS0,115200 mtdparts=nand_mtd:1m(u-boot),16m(uImage),-(root) root=/dev/mtdblock2 ro reset=0 productType=BIG5_KW cap=gpt,lba64

Starting kernel ...

Uncompressing Linux................................................................................................................................................................................................. done, booting the kernel.
[    0.000000] Linux version 2.6.31.14-svn6790 (sbs@node2.lacie.com) (gcc version 4.2.1) #1 Mon Dec 12 16:16:25 UTC 2011
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: net5big_nand_v2
[    0.000000] Using UBoot passing parameters structure
[    0.000000] Memory policy: ECC disabled, Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 mtdparts=nand_mtd:1m(u-boot),16m(uImage),-(root) root=/dev/mtdblock2 ro reset=0 productType=BIG5_KW cap=gpt,lba64
[    0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 256MB 256MB = 512MB total
[    0.000000] Memory: 508672KB available (5416K code, 377K data, 148K init, 0K highmem)
[    0.000000] Hierarchical RCU implementation.
[    0.000000] NR_IRQS:128
[    0.000000] Console: colour dummy device 80x30
[    0.000000] Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544)
[    0.230000] Mount-cache hash table entries: 512
[    0.230000] CPU: Testing write buffer coherency: ok
[    0.230000] xor: measuring software checksum speed
[    0.280000]    arm4regs  :  1089.600 MB/sec
[    0.330000]    8regs     :   826.800 MB/sec
[    0.380000]    32regs    :   927.200 MB/sec
[    0.380000] xor: using function: arm4regs (1089.600 MB/sec)
[    0.380000] NET: Registered protocol family 16
[    0.380000] Feroceon L2: Enabling L2
[    0.380000] Feroceon L2: Cache support initialised.
[    0.380000]
[    0.380000] CPU Interface
[    0.380000] -------------
[    0.380000] SDRAM_CS0 ....base 00000000, size 256MB
[    0.380000] SDRAM_CS1 ....base 10000000, size 256MB
[    0.380000] SDRAM_CS2 ....disable
[    0.380000] SDRAM_CS3 ....disable
[    0.380000] PEX0_MEM ....base e8000000, size 128MB
[    0.380000] PEX0_IO ....base f2000000, size   1MB
[    0.380000] INTER_REGS ....base f1000000, size   1MB
[    0.380000] NFLASH_CS ....base fa000000, size   2MB
[    0.380000] SPI_CS ....base f4000000, size  16MB
[    0.380000] BOOT_ROM_CS ....no such
[    0.380000] DEV_BOOTCS ....no such
[    0.380000] CRYPT_ENG ....base f0000000, size   2MB
[    0.380000]
[    0.380000]   Marvell Development Board (LSP Version KW_LSP_5.0.3)-- net5big_v2  Soc: 88F6281 A1 LE
[    0.380000]
[    0.380000]  Detected Tclk 166666667 and SysClk 400000000
[    0.380000] Register Marvell USB EHCI Host controller #0
[    0.390000] bio: create slab <bio-0> at 0
[    0.390000] SCSI Scattered Spinup: Enabled
[    0.390000]   o Maximum Disk Spinup: 1
[    0.390000]   o Disk Spinup timeout: 10
[    0.390000] SCSI subsystem initialized
[    0.560000] raid6: int32x1     91 MB/s
[    0.730000] raid6: int32x2    107 MB/s
[    0.900000] raid6: int32x4    123 MB/s
[    1.070000] raid6: int32x8    108 MB/s
[    1.070000] raid6: using algorithm int32x4 (123 MB/s)
[    1.070000] NET: Registered protocol family 2
[    1.070000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[    1.070000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[    1.070000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[    1.070000] TCP: Hash tables configured (established 16384 bind 16384)
[    1.070000] TCP reno registered
[    1.070000] NET: Registered protocol family 1
[    1.070000] Trying to unpack rootfs image as initramfs...
[    1.080000] Switched to NOHz mode on CPU #0
[    1.350000] Freeing initrd memory: 4400K
[    1.350000] cpufreq: Init kirkwood cpufreq driver
[    1.370000] cesadev_init(c000ee90)
[    1.370000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[    1.370000] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
[    1.370000] gpio-usb gpio-usb: USB GPIO's initialized
[    1.370000] g762 0-003e: found a platform specific fan speed array
[    1.370000] g762 0-003e: device successfully initialized
[    1.370000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    1.370000] Registering unionfs 2.5.10 (for 2.6.31.14)
[    1.370000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    1.370000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    1.380000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[    1.380000] SGI XFS Quota Management subsystem
[    1.380000] msgmni has been set to 1002
[    1.380000] alg: No test for cipher_null (cipher_null-generic)
[    1.380000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[    1.380000] alg: No test for digest_null (digest_null-generic)
[    1.380000] alg: No test for compress_null (compress_null-generic)
[    1.380000] alg: No test for stdrng (krng)
[    1.470000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[    1.510000] async_tx: api initialized (async)
[    1.510000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    1.510000] io scheduler noop registered
[    1.510000] io scheduler anticipatory registered (default)
[    1.510000] io scheduler deadline registered
[    1.510000] io scheduler cfq registered
[    1.520000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.520000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[    1.520000] console [ttyS0] enabled
[    2.020000] brd: module loaded
[    2.020000] at24 0-0050: 512 byte 24c04 EEPROM (writable)
[    2.020000] sata_mv sata_mv.0: version 1.28
[    2.030000] sata_mv sata_mv.0: slots 32 ports 2
[    2.030000] scsi0 : sata_mv
[    2.040000] scsi1 : sata_mv
[    2.040000] ata1: SATA max UDMA/133 irq 21
[    2.040000] ata2: SATA max UDMA/133 irq 21
[    2.050000] INIT Marvell Ethernet Driver: mv_netdev
[    2.050000] Loading Marvell Ethernet Driver:
[    2.060000]   o Cached descriptors in DRAM
[    2.060000]   o DRAM SW cache-coherency
[    2.070000]   o 2 Giga ports supported
[    2.070000]   o Single RX Queue support - ETH_DEF_RXQ=0
[    2.080000]   o Single TX Queue support - ETH_DEF_TXQ=0
[    2.080000]   o TCP segmentation offload (TSO) supported
[    2.090000]   o Large Receive offload (LRO) supported
[    2.090000]   o Receive checksum offload supported
[    2.100000]   o Transmit checksum offload supported
[    2.100000]   o Network Fast Processing (Routing) supported - (Disabled)
[    2.110000]   o Proc tool API enabled
[    2.110000]   o SKB Reuse supported - (Disabled)
[    2.120000]   o SKB Recycle supported - (Disabled)
[    2.120000]   o Rx descripors: q0=128
[    2.120000]   o Tx descripors: q0=532
[    2.130000]   o Loading network interface(s):
[    2.130000]     o  register under mv_netdev platform
[    2.140000]     o eth0, ifindex = 2, GbE port = 0
[    2.140000]     o eth1, ifindex = 3, GbE port = 1
[    2.150000]
[    2.150000] mvFpRuleDb (dfc94000): 4096 entries, 16384 bytes
[    2.160000] console [netcon0] enabled
[    2.160000] netconsole: network logging started
[    2.170000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
[    2.170000] Scanning device for bad blocks
[    2.310000] Creating 3 MTD partitions on "orion_nand":
[    2.310000] 0x000000000000-0x000000100000 : "u-boot"
[    2.320000] 0x000000100000-0x000001100000 : "uImage"
[    2.330000] 0x000001100000-0x000010000000 : "root"
[    2.330000] mice: PS/2 mouse device common for all mice
[    2.340000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[    2.350000] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[    2.440000] md: linear personality registered for level -1
[    2.440000] md: raid0 personality registered for level 0
[    2.450000] md: raid1 personality registered for level 1
[    2.450000] md: raid10 personality registered for level 10
[    2.460000] md: raid6 personality registered for level 6
[    2.460000] md: raid5 personality registered for level 5
[    2.470000] md: raid4 personality registered for level 4
[    2.470000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[    2.490000] cpuidle: using governor ladder
[    2.490000] cpuidle: using governor menu
[    2.490000] Registered led device: net5big-v2:blue:power
[    2.500000] Registered led device: net5big-v2:red:power
[    2.500000] Registered led device: net5big-v2:blue:sata0
[    2.510000] Registered led device: net5big-v2:red:sata0
[    2.520000] Registered led device: net5big-v2:blue:sata1
[    2.520000] Registered led device: net5big-v2:red:sata1
[    2.530000] Registered led device: net5big-v2:blue:sata2
[    2.530000] Registered led device: net5big-v2:red:sata2
[    2.540000] Registered led device: net5big-v2:blue:sata3
[    2.540000] Registered led device: net5big-v2:red:sata3
[    2.550000] Registered led device: net5big-v2:blue:sata4
[    2.550000] Registered led device: net5big-v2:red:sata4
[    2.560000] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[    2.570000] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[    2.610000] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    2.630000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    2.630000] ata1.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    2.640000] ata1.00: hard resetting link
[    2.660000] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[    2.700000] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[    2.740000] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[    2.740000] TCP cubic registered
[    2.740000] NET: Registered protocol family 17
[    2.750000] Bridge firewalling registered
[    2.750000] NET: Registered protocol family 5
[    2.760000] RPC: Registered udp transport module.
[    2.760000] RPC: Registered tcp transport module.
[    2.770000] rtc-mv rtc-mv: setting system clock to 2021-07-26 03:18:48 UTC (1627269528)
[    2.990000] ata1.01: hard resetting link
[    3.340000] ata1.02: hard resetting link
[    3.690000] ata1.03: hard resetting link
[    4.040000] ata1: EH complete
[    4.550000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    4.550000] ata2.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    4.560000] ata2.00: hard resetting link
[    4.910000] ata2.01: hard resetting link
[    5.260000] ata2.02: hard resetting link
[    5.610000] ata2.03: hard resetting link
[    5.960000] ata2: EH complete
[    5.960000] Freeing init memory: 148K
[    5.960000] Freeing initramfs memory: 4K
load RTC  date: Mon Jul 26 03:18:51 UTC 2021
save file date: Mon Jul 26 03:18:51 UTC 2021
       _            ____
      | |     __ _ / ___)_  ___
      | |    / _` | /   (_)/ _ \
      | |___| (_| | \___| |  __/
      |_____)\__,_|\____)_|\___)
   ____                      _
  / ___) __ _ ____  ___ _  _| | ___
 | /    / _` |  _ \/ __| || | |/ _ \
 | \___| (_| | |_) |__ \ \/ | |  __/
  \____)\__,_|  __/\___/\__/|_|\___)
             |_|

--- set up network via DHCP
udhcpc (v1.16.2) started
[    8.440000] eth0: started





Sending discover...



Sending discover...
Sending discover...
No lease, forking to background
--- start ipcommd
wait 2 seconds
--- startup done
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
--- drives 5
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
not all drives detected [0 / 5]
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
--- mount /dev/mtdblock2
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
[   45.420000] uncorrectable error :
[   45.420000] uncorrectable error :
[   45.430000] uncorrectable error :
[   45.430000] uncorrectable error :
[   45.430000] uncorrectable error :
[   45.440000] uncorrectable error :
[   45.440000] uncorrectable error :
[   45.440000] uncorrectable error :
[   45.450000] uncorrectable error :
[   45.450000] uncorrectable error :
[   45.450000] uncorrectable error :
[   45.460000] uncorrectable error :
[   45.460000] uncorrectable error :
[   45.460000] uncorrectable error :
[   45.490000] mtd->read(0x1f4b4 bytes from 0x2a40b4c) returned ECC error
[   45.500000] Old JFFS2 bitmask found at 0x02a47d28
[   45.500000] You cannot use older JFFS2 filesystems with newer kernels
[   45.510000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d2c: 0x1040 instead
[   45.520000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d30: 0x5868 instead
[   45.530000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d34: 0x0008 instead
[   45.540000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d38: 0x286c instead
[   45.550000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d3c: 0x81a0 instead
[   45.560000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d40: 0x0060 instead
[   45.570000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d44: 0x2928 instead
[   45.570000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d48: 0x41c6 instead
[   45.580000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d4c: 0x41c6 instead
[   45.590000] jffs2_scan_eraseblock(): Magic bitmask 0x1985 not found at 0x02a47d50: 0x41c6 instead
[   45.600000] Further such events for this erase block will not be printed
[   45.610000] Old JFFS2 bitmask found at 0x02a484c0
[   45.610000] You cannot use older JFFS2 filesystems with newer kernels
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
--- checksum description.xml
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
Kernel version: 2.6.31.14-svn6790
Capsule version: 2.2.3
--- init 2.2.3
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- checksum partitions.map
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- checksum partitions.gpt
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- checksum uImage
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- checksum bootfs.tar.lzma
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- checksum rootfs.tar.lzma
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
[   64.870000] uncorrectable error :
[   64.870000] uncorrectable error :
[   64.870000] uncorrectable error :
[   64.880000] uncorrectable error :
[   64.880000] uncorrectable error :
[   64.880000] uncorrectable error :
[   64.890000] uncorrectable error :
[   64.890000] uncorrectable error :
[   64.900000] uncorrectable error :
[   64.900000] mtd->read(0xd28 bytes from 0x2a47000) returned ECC error
[   64.910000] JFFS2 notice: (1024) check_node_data: wrong data CRC in data node at 0x02a46ce4: read 0x8a4b4a6b, calculated 0x988b1269.
[   87.010000] eth0: link up, full duplex, speed 1 Gbps
### file /mnt/flash_ro/repository/rootfs.tar.lzma is probably corrupted
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
### error during the NAS rescue procedure
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
---+--- reboot
connect_to_notifier: connect failed: Connection refused
ERROR: send_event_notification failed
Error when sending notification. Continue...
save file date: Mon Jul 26 03:20:17 UTC 2021
save RTC  date: Mon Jul 26 03:20:17 UTC 2021
umount: can't umount /: Device or resource busy
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system reboot
[   94.730000] eth0: link down
[   94.810000] md: stopping all md devices.
[   95.810000] Restarting system.
[   95.810000] Resetting !!
▒


[fvdw]

This is lacie firmware loaded from nand flash memory, seems no disks are detected,vwere there any disk in the nas during this boot?

[danilomag]

yes, the first time I had no disk connected.
now i connected all disks.
this time it won't reboot, but no ip address is assigned.
It asks me to enter login and password

[danilomag]

Code: Select all

Hit any key to stop autoboot: 0


I can't stop booting. Also I can get an ip address only if the hard drives are all unplugged.