danilomag wrote:same as booting with no disks?
Yes exactly.
however I discovered that via serial cable I can interrupt the boot with ctrl-c
Do you get then a prompt lije this
- Code: Select all
marvell>>
danilomag wrote:same as booting with no disks?
Yes exactly.
however I discovered that via serial cable I can interrupt the boot with ctrl-c
marvell>>
marvell>>
Do you get this directly after waiting for uboot so with the nas switched off, or does this start after starting the nas??
It is very strange output, never seen this before
danilomag wrote:marvell>>
yes
printenv
Do you get this directly after waiting for uboot so with the nas switched off, or does this start after starting the nas??
It is very strange output, never seen this before
after starting the nas, immediately after Waiting for LUMP (3)
Marvell>> printenv
baudrate=115200
loads_echo=0
rootpath=/mnt/ARM_FS/
console=console=ttyS0,115200 mtdparts=nand_mtd:0xa0000@0(uboot)ro,0xff00000@0x100000(root)
CASset=min
MALLOC_len=1
ethprime=egiga0
bootargs_root=root=/dev/nfs rw
bootargs_end=:::DB88FXX81:eth0:none
image_name=uImage
standalone=fsload 0x2000000 $(image_name);setenv bootargs $(console) root=/dev/mtdblock0 rw ip=$(ipaddr):$(serverip)$(bootargs_end) $(mvPhoneConfig); bootm 0x2000000;
ethmtu=1500
eth1mtu=1500
mvPhoneConfig=mv_phone_config=dev0:fxs,dev1:fxs
mvNetConfig=mv_net_config=(00:11:88:0f:62:81,0:1:2:3),mtu=1500
usb0Mode=host
yuk_ethaddr=00:00:00:EE:51:81
nandEcc=1bit
netretry=no
rcvrip=169.254.100.100
loadaddr=0x02000000
autoload=no
partition=nand0,0
mtddevnum=0
mtddevname=u-boot
gatewayip=192.168.1.1
netmask=255.255.255.0
ipaddr=192.168.1.185
serverip=192.168.1.185
stdin=serial
stdout=serial
stderr=serial
mainlineLinux=no
enaMonExt=no
enaCpuStream=no
enaWrAllo=no
pexMode=RC
disL2Cache=no
setL2CacheWT=yes
disL2Prefetch=yes
enaICPref=yes
enaDCPref=yes
sata_dma_mode=yes
netbsd_en=no
vxworks_en=no
disaMvPnp=no
enaAutoRecovery=yes
uboot_capabilities=gpt,lba64
start_lump=lump 3
pre_lump=lump 1
resetdisk=ide reset
bootdelay=0
boot_fail=lump
kernel_addr=0x800000
productType_env=BIG5_KW
primaryPart=6
secondaryPart=A
boot_usb=usb start;usbboot 0x800000 0:1;bootm;
resetFlag_env=0
bootargs=console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=PRO_KW
bootcmd=run disk_disk
mtdids=nand0=nand_mtd
mtdparts=mtdparts=nand_mtd:1m(u-boot),16m(uImage),-(root)
boot_nand=setenv bootargs console=ttyS0,115200 ${mtdparts} root=/dev/mtdblock2 ro reset=${resetFlag_env} productType=${productType_env}; nboot ${kernel_addr} uImage; bootm ${kernel_addr}
boot_disk10=if disk ${kernel_addr} 5:${primaryPart}; then setenv rootfs /dev/sde7; else run boot_nand; fi
boot_disk9=if disk ${kernel_addr} 6:${primaryPart}; then setenv rootfs /dev/sdd7; else run boot_disk10; fi
boot_disk8=if disk ${kernel_addr} 1:${primaryPart}; then setenv rootfs /dev/sdc7; else run boot_disk9; fi
boot_disk7=if disk ${kernel_addr} 2:${primaryPart}; then setenv rootfs /dev/sdb7; else run boot_disk8; fi
boot_disk6=if disk ${kernel_addr} 3:${primaryPart}; then setenv rootfs /dev/sda7; else run boot_disk7; fi
boot_disk5=if disk ${kernel_addr} 5:${secondaryPart}; then setenv rootfs /dev/sde7; else run boot_disk6; fi
boot_disk4=if disk ${kernel_addr} 6:${secondaryPart}; then setenv rootfs /dev/sdd7; else run boot_disk5; fi
boot_disk3=if disk ${kernel_addr} 1:${secondaryPart}; then setenv rootfs /dev/sdc7; else run boot_disk4; fi
boot_disk2=if disk ${kernel_addr} 2:${secondaryPart}; then setenv rootfs /dev/sdb7; else run boot_disk3; fi
boot_disk1=if disk ${kernel_addr} 3:${secondaryPart}; then setenv rootfs /dev/sda7; else run boot_disk2; fi
boot_disk=if test ${resetFlag_env} -eq 0; then run boot_disk1; else run boot_disk6; fi
disk_disk=run boot_disk; setenv bootargs console=ttyS0,115200 root=${rootfs} ro reset=${resetFlag_env} productType=${productType_env}; bootm ${kernel_addr};
ethaddr=00:D0:4B:92:5C:A5
eth1addr=00:D0:4B:92:5C:A6
ethact=egiga0
ide reset
tftpboot 0x800000 UIMAGE-3142-KIRKWOOD-171-standalone
bootm
Marvell>> ide reset
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
[0 0 3]: Enable DMA mode
Device 3 @ 0 0 3:
Model: WDC WD2003FZEX-00Z4SA0 Firm: 01.01A01 Ser#: WD-WMC5C0D5JEHR
Type: Hard Disk
dev_desc->blksz = 512
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (3907029168 x 512)
Port Multiplier found @ 0 1. Vendor: 11ab ports: 4
Marvell>> tftpboot 0x800000 UIMAGE-3142-KIRKWOOD-171-standalone
Using egiga0 device
TFTP from server 192.168.1.185; our IP address is 192.168.1.185
Filename 'UIMAGE-3142-KIRKWOOD-171-standalone'.
Load address: 0x800000
Loading: T T T T T T T T T T
Retry count exceeded; starting again
Marvell>>
Return to Lacie 5big Network vs2
Users browsing this forum: No registered users and 6 guests