help slot error ?? it only starts with two slots

[fvdw]

give command

Code: Select all

fvdw-sl-programs

and install firmware on this disk

[fvdw]

if the installer cannot find sda then indeed probably the first slot is defective

[fvdw]

In case slot 1 seems to be defective switch of your nas nad put disk in slot 2, start again the standalone kernel and post output of dmesg
If now we find a disk in dmesg identified as sdb then a solution to revive your nas is to make a dedicate kernel that boots from slot 2.

[fvdw]

I go to bed now :z)

[taetae]

give command

Code: Select all

fvdw-sl-programs

and install firmware on this disk

Code: Select all

fdisk: can't open '/dev/sda': No such device or address
diskid=none

There was an error detecting device sda, this device is required to install firmware.
Installer will exit
root@fvdw-sta-kirkwood:/ #

fdisk -l

Code: Select all

root@fvdw-sta-kirkwood:/ # fdisk  -l

Disk /dev/mtdblock1: 16 MB, 16777216 bytes
255 heads, 63 sectors/track, 2 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Disk /dev/mtdblock1 doesn't contain a valid partition table

Disk /dev/mtdblock2: 250 MB, 250609664 bytes
255 heads, 63 sectors/track, 30 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes

Disk /dev/mtdblock2 doesn't contain a valid partition table
root@fvdw-sta-kirkwood:/ #

good night and thanks again for the help
__________________________________________________________

good morning

sees the disk in position 2 sdb

[fvdw]

...
good morning

sees the disk in position 2 sdb

Please post output of dmesg command

[fvdw]

...
good morning

sees the disk in position 2 sdb

Please post output of dmesg command

Taetae, did you see the previous post?

Please load standalone kernel with a disk in the second slot and post the output of dmesg, or even better if you would put a disk in all four slots 2,3,4 and 5
Post the output of

Code: Select all

dmesg

I need it to be sure that other sata ports work and make a dedicated kernel for you.

[taetae]

...
good morning

sees the disk in position 2 sdb

Please post output of dmesg command

Taetae, did you see the previous post?

Please load standalone kernel with a disk in the second slot and post the output of dmesg, or even better if you would put a disk in all four slots 2,3,4 and 5
Post the output of

Code: Select all

dmesg

I need it to be sure that other sata ports work and make a dedicated kernel for you.

this is with slots 2,3,4,5

Code: Select all

fvdw-sta-kirkwood login: root
Password:
root@fvdw-sta-kirkwood:/ # dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #171 PREEMPT Wed Jan 17 23:33:31 CET 2018
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie 5Big Network Nand v2
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0982898, node_mem_map dfbfb000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.2/ cap=gpt,lba64
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 509780K/524288K available (5950K kernel code, 220K rwdata, 1596K rodata, 1933K init, 233K bss, 14508K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0766b44   (7547 kB)
[    0.000000]       .init : 0xc0767000 - 0xc094a4cc   (1934 kB)
[    0.000000]       .data : 0xc094c000 - 0xc0983100   ( 221 kB)
[    0.000000]        .bss : 0xc098310c - 0xc09bd56c   ( 234 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[   22.423248] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[   22.513218] pid_max: default: 32768 minimum: 301
[   22.513352] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   22.513371] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   22.513919] CPU: Testing write buffer coherency: ok
[   22.514229] Setting up static identity map for 0x5a6ac0 - 0x5a6b18
[   22.516862] VFP support v0.3: not present
[   22.517392] xor: measuring software checksum speed
[   22.613251]    arm4regs  :  1089.200 MB/sec
[   22.713212]    8regs     :   654.400 MB/sec
[   22.813202]    32regs    :   905.600 MB/sec
[   22.813219] xor: using function: arm4regs (1089.200 MB/sec)
[   22.813237] pinctrl core: initialized pinctrl subsystem
[   22.813352] NET: Registered protocol family 16
[   22.813734] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   22.816467] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   22.816491] Feroceon L2: Enabling L2
[   22.816529] Feroceon L2: Cache support initialised.
[   22.817618] mv_usb_init 1
[   22.817637] mv_usb_init 2 devnum = 0
[   22.817650] init function mv_usb_init finished
[   22.817658] initial MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[   22.817689]   final MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[   22.817874]  orion-ehci registered
[   22.819699] orion_gpio_is_valid: invalid GPIO 7
[   22.820201] Kirkwood PCIe port 0: link down
[   22.820211] Kirkwood PCIe port 1: link up
[   22.820220] PCI: bus0 uses PCIe port 0
[   22.820461] PCI host bridge to bus 0000:00
[   22.820482] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   22.820496] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   22.820509] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   22.820557] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[   22.820586] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[   22.820605] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x1fffffff]
[   22.820655] pci 0000:00:00.0: supports D1 D2
[   22.820931] PCI: bus0: Fast back to back transfers disabled
[   22.820950] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[   22.820963] PCI: bus1 uses PCIe port 1
[   22.821185] PCI host bridge to bus 0000:01
[   22.821204] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[   22.821217] pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
[   22.821229] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[   22.821267] PCI: bus1: Fast back to back transfers enabled
[   22.821281] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   22.845442] bio: create slab <bio-0> at 0
[   23.014368] raid6: int32x1     95 MB/s
[   23.183360] raid6: int32x2    123 MB/s
[   23.353429] raid6: int32x4    120 MB/s
[   23.523296] raid6: int32x8    128 MB/s
[   23.523306] raid6: using algorithm int32x8 (128 MB/s)
[   23.523314] raid6: using intx1 recovery algorithm
[   23.524145] SCSI subsystem initialized
[   23.524600] libata version 3.00 loaded.
[   23.525481] usbcore: registered new interface driver usbfs
[   23.525656] usbcore: registered new interface driver hub
[   23.525853] usbcore: registered new device driver usb
[   23.528331] cfg80211: Calling CRDA to update world regulatory domain
[   23.528597] Switched to clocksource orion_clocksource
[   23.530862] NET: Registered protocol family 2
[   23.531330] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[   23.531389] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[   23.531441] TCP: Hash tables configured (established 4096 bind 4096)
[   23.531493] TCP: reno registered
[   23.531507] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   23.531529] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   23.531720] NET: Registered protocol family 1
[   23.531989] RPC: Registered named UNIX socket transport module.
[   23.532000] RPC: Registered udp transport module.
[   23.532007] RPC: Registered tcp transport module.
[   23.532014] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   23.532035] PCI: CLS 32 bytes, default 32
[   23.678554] NetWinder Floating Point Emulator V0.97 (double precision)
[   23.678679] gpio-usb-probe-4b err=0
[   23.678694] gpio-usb gpio-usb: USB GPIO's initialized
[   23.680292] futex hash table entries: 256 (order: -1, 3072 bytes)
[   23.781955] VFS: Disk quotas dquot_6.5.2
[   23.782005] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   23.782435] NFS: Registering the id_resolver key type
[   23.782492] Key type id_resolver registered
[   23.782501] Key type id_legacy registered
[   23.782519] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   23.782534] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   23.782635] NTFS driver 2.1.30 [Flags: R/W].
[   23.782666] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   23.782812] fuse init (API version 7.22)
[   23.783433] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[   23.783845] msgmni has been set to 995
[   23.784959] async_tx: api initialized (async)
[   23.785146] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   23.785158] io scheduler noop registered
[   23.785167] io scheduler deadline registered
[   23.785186] io scheduler cfq registered (default)
[   23.785569] mv_xor mv_xor.0: Marvell shared XOR driver
[   23.823229] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   23.863226] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   23.863476] mv_xor mv_xor.1: Marvell shared XOR driver
[   23.903225] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   23.943225] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   23.949115] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   23.970228] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   24.596281] console [ttyS0] enabled
[   24.609169] brd: module loaded
[   24.616868] loop: module loaded
[   24.620304] Uniform Multi-Platform E-IDE driver
[   24.625177] ide-gd driver 1.18
[   24.629728] sata_mv sata_mv.0: version 1.28
[   24.629791] sata_mv sata_mv.0: cannot get optional clkdev
[   24.635622] sata_mv sata_mv.0: slots 32 ports 2
[   24.643167] scsi0 : sata_mv
[   24.646682] scsi1 : sata_mv
[   24.649876] ata1: SATA max UDMA/133 irq 21
[   24.654072] ata2: SATA max UDMA/133 irq 21
[   24.660319] nand: Could not find valid ONFI parameter page; aborting
[   24.666753] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[   24.673079] nand: Hynix NAND 256MiB 3,3V 8-bit
[   24.677607] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[   24.683289] Scanning device for bad blocks
[   24.714230] Bad eraseblock 337 at 0x000002a20000
[   24.854892] Creating 3 MTD partitions on "orion_nand":
[   24.860010] 0x000000000000-0x000000100000 : "u-boot"
[   24.866110] 0x000000100000-0x000001100000 : "uImage"
[   24.872127] 0x000001100000-0x000010000000 : "root"
[   24.880077] tun: Universal TUN/TAP device driver, 1.6
[   24.885177] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   24.891516] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   24.899906] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   24.916249] libphy: orion_mdio_bus: probed
[   24.920498] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   25.163198] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   25.183277] ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   25.244773] ata1.00: hard resetting link
[   25.593951] ata1.01: hard resetting link
[   26.038509] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:92:5c:4b
[   26.113473] ata1.02: hard resetting link
[   26.623450] ata1.03: hard resetting link
[   27.033860] ata1.01: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[   27.040097] ata1.01: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   27.143234] ata1.01: configured for UDMA/133
[   27.149867] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:4b:92:5c:4c
[   27.158705] PPP generic driver version 2.4.2
[   27.163534] PPP Deflate Compression module registered
[   27.168572] PPP MPPE Compression module registered
[   27.173397] NET: Registered protocol family 24
[   27.178004] usbcore: registered new interface driver rtl8187
[   27.183848] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[   27.191358] usbcore: registered new interface driver pegasus
[   27.197209] usbcore: registered new interface driver asix
[   27.202765] usbcore: registered new interface driver ax88179_178a
[   27.208920] ata1.02: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[   27.215347] usbcore: registered new interface driver cdc_ether
[   27.221329] ata1.02: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   27.228249] usbcore: registered new interface driver net1080
[   27.234218] usbcore: registered new interface driver cdc_subset
[   27.240289] usbcore: registered new interface driver zaurus
[   27.246043] usbcore: registered new interface driver ipheth
[   27.251792] usbcore: registered new interface driver cdc_ncm
[   27.258539] aoe: cannot create debugfs directory
[   27.263321] aoe: AoE v85 initialised.
[   27.267711] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   27.273840] i2c /dev entries driver
[   27.278283] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[   27.297788] md: linear personality registered for level -1
[   27.303285] md: raid0 personality registered for level 0
[   27.308572] md: raid1 personality registered for level 1
[   27.314005] md: raid10 personality registered for level 10
[   27.319605] md: raid6 personality registered for level 6
[   27.324933] md: raid5 personality registered for level 5
[   27.330216] md: raid4 personality registered for level 4
[   27.335834] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[   27.344483] device-mapper: multipath: version 1.6.0 loaded
[   27.349943] device-mapper: multipath round-robin: version 1.0.0 loaded
[   27.356538] device-mapper: multipath queue-length: version 0.1.0 loaded
[   27.363118] device-mapper: multipath service-time: version 0.2.0 loaded
[   27.369788] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   27.375990] device-mapper: raid: Loading target version 1.5.2
[   27.385823] ipip: IPv4 over IPv4 tunneling driver
[   27.391256] TCP: cubic registered
[   27.394743] NET: Registered protocol family 10
[   27.400092] sit: IPv6 over IPv4 tunneling driver
[   27.405580] NET: Registered protocol family 17
[   27.410260] NET: Registered protocol family 5
[   27.414982] 8021q: 802.1Q VLAN Support v1.8
[   27.419180] NET: Registered protocol family 37
[   27.423715] Key type dns_resolver registered
[   27.429131] netpoll: netconsole: local port 6666
[   27.433958] netpoll: netconsole: local IPv4 address 192.168.1.252
[   27.440022] netpoll: netconsole: interface 'eth0'
[   27.444739] netpoll: netconsole: remote port 6666
[   27.449423] netpoll: netconsole: remote IPv4 address 192.168.1.2
[   27.455691] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   27.462540] netpoll: netconsole: device eth0 not up yet, forcing it
[   27.493249] ata1.02: configured for UDMA/133
[   27.497685] ata1: EH complete
[   27.513473] scsi 0:1:0:0: Direct-Access     ATA      ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[   27.522035] fvdw1 disk index before get_sd_name = 0
[   27.527066] device-name= sata_mv
[   27.530295] fvdw2 disk index after get_sd_name = 2
[   27.535091] fvdw3 prefix[0]=s  prefix[1]=d
[   27.539166] fvdw4 diskname = sdc
[   27.542875] sd 0:1:0:0: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   27.563478] sd 0:1:0:0: Attached scsi generic sg0 type 0
[   27.568939] sd 0:1:0:0: [sdc] 4096-byte physical blocks
[   27.574496] scsi 0:2:0:0: Direct-Access     ATA      ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[   27.582973] sd 0:1:0:0: [sdc] Write Protect is off
[   27.593456] sd 0:1:0:0: [sdc] Mode Sense: 00 3a 00 00
[   27.593575] sd 0:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   27.602791] fvdw1 disk index before get_sd_name = 1
[   27.613200] device-name= sata_mv
[   27.616416] fvdw2 disk index after get_sd_name = 1
[   27.621183] fvdw3 prefix[0]=s  prefix[1]=d
[   27.643192] fvdw4 diskname = sdb
[   27.646755] sd 0:2:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   27.659870] sd 0:2:0:0: Attached scsi generic sg1 type 0
[   27.665222] sd 0:2:0:0: [sdb] 4096-byte physical blocks
[   27.679753] sd 0:2:0:0: [sdb] Write Protect is off
[   27.684610] sd 0:2:0:0: [sdb] Mode Sense: 00 3a 00 00
[   27.684722] sd 0:2:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   27.693779]  sdc: sdc1 sdc2 sdc3 sdc4 < sdc5 sdc6 sdc7 sdc8 >
[   27.724227] sd 0:1:0:0: [sdc] Attached SCSI disk
[   27.768892]  sdb: sdb8
[   27.784225] sd 0:2:0:0: [sdb] Attached SCSI disk
[   28.173202] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   28.193194] ata2.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   28.254853] ata2.00: hard resetting link
[   28.603954] ata2.01: hard resetting link
[   28.698115] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   28.963951] ata2.02: hard resetting link
[   29.473443] ata2.03: hard resetting link
[   29.863233] ata2.02: ATA-8: ST2000DL001-9VT156, CC41, max UDMA/133
[   29.869386] ata2.02: 3907029168 sectors, multi 0: LBA48
[   29.933233] ata2.02: configured for UDMA/133
[   29.937664] ata2: EH complete
[   29.953453] scsi 1:2:0:0: Direct-Access     ATA      ST2000DL001-9VT1 CC41 PQ: 0 ANSI: 5
[   29.961993] fvdw1 disk index before get_sd_name = 2
[   29.966906] device-name= sata_mv
[   29.970116] fvdw2 disk index after get_sd_name = 3
[   29.974913] fvdw3 prefix[0]=s  prefix[1]=d
[   29.978989] fvdw4 diskname = sdd
[   29.982694] sd 1:2:0:0: [sdd] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   29.990738] sd 1:2:0:0: Attached scsi generic sg2 type 0
[   29.996118] sd 1:2:0:0: [sdd] 4096-byte physical blocks
[   30.001804] sd 1:2:0:0: [sdd] Write Protect is off
[   30.006647] sd 1:2:0:0: [sdd] Mode Sense: 00 3a 00 00
[   30.006758] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   30.068055]  sdd: sdd4 < sdd5 sdd6 sdd7 sdd8 >
[   30.074585] sd 1:2:0:0: [sdd] Attached SCSI disk
[   31.494310] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   31.504132] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   31.514158] console [netcon0] enabled
[   31.517812] netconsole: network logging started
[   31.522815] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   31.530219] rtc-mv rtc-mv: setting system clock to 2020-12-06 21:39:51 UTC (1607290791)
[   31.543957] Freeing unused kernel memory: 1932K (c0767000 - c094a000)
[   32.632993] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   41.711685] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   41.721925] ehci-orion: EHCI orion driver
[   41.726141] orion-ehci orion-ehci.0: EHCI Host Controller
[   41.731562] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   41.739275] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   41.763206] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   41.769253] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   41.776057] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   41.783282] usb usb1: Product: EHCI Host Controller
[   41.788153] usb usb1: Manufacturer: Linux 3.14.2 ehci_hcd
[   41.793561] usb usb1: SerialNumber: orion-ehci.0
[   41.798901] hub 1-0:1.0: USB hub found
[   41.802707] hub 1-0:1.0: 1 port detected
[   41.813261] usbcore: registered new interface driver usb-storage
[   42.123231] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   42.273666] usb 1-1: New USB device found, idVendor=0424, idProduct=2512
[   42.280362] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   42.288334] hub 1-1:1.0: USB hub found
[   42.292161] hub 1-1:1.0: 2 ports detected
root@fvdw-sta-kirkwood:/ #


slot 2 only

Code: Select all

root@fvdw-sta-kirkwood:/ # dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #171 PREEMPT Wed Jan 17 23:33:31 CET 2018
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie 5Big Network Nand v2
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0982898, node_mem_map dfbfb000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.2/ cap=gpt,lba64
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 509780K/524288K available (5950K kernel code, 220K rwdata, 1596K rodata, 1933K init, 233K bss, 14508K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0766b44   (7547 kB)
[    0.000000]       .init : 0xc0767000 - 0xc094a4cc   (1934 kB)
[    0.000000]       .data : 0xc094c000 - 0xc0983100   ( 221 kB)
[    0.000000]        .bss : 0xc098310c - 0xc09bd56c   ( 234 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[   16.280896] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[   16.370866] pid_max: default: 32768 minimum: 301
[   16.371001] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   16.371020] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[   16.371567] CPU: Testing write buffer coherency: ok
[   16.371877] Setting up static identity map for 0x5a6ac0 - 0x5a6b18
[   16.374508] VFP support v0.3: not present
[   16.375039] xor: measuring software checksum speed
[   16.470896]    arm4regs  :  1089.200 MB/sec
[   16.570859]    8regs     :   654.400 MB/sec
[   16.670850]    32regs    :   905.600 MB/sec
[   16.670868] xor: using function: arm4regs (1089.200 MB/sec)
[   16.670883] pinctrl core: initialized pinctrl subsystem
[   16.670999] NET: Registered protocol family 16
[   16.671378] DMA: preallocated 256 KiB pool for atomic coherent allocations
[   16.674121] Kirkwood: MV88F6281-A1, TCLK=166666667.
[   16.674147] Feroceon L2: Enabling L2
[   16.674184] Feroceon L2: Cache support initialised.
[   16.675276] mv_usb_init 1
[   16.675295] mv_usb_init 2 devnum = 0
[   16.675307] init function mv_usb_init finished
[   16.675315] initial MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[   16.675347]   final MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[   16.675532]  orion-ehci registered
[   16.677360] orion_gpio_is_valid: invalid GPIO 7
[   16.677865] Kirkwood PCIe port 0: link down
[   16.677875] Kirkwood PCIe port 1: link up
[   16.677884] PCI: bus0 uses PCIe port 0
[   16.678124] PCI host bridge to bus 0000:00
[   16.678145] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[   16.678159] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[   16.678172] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[   16.678220] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[   16.678249] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[   16.678267] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x1fffffff]
[   16.678318] pci 0000:00:00.0: supports D1 D2
[   16.678592] PCI: bus0: Fast back to back transfers disabled
[   16.678611] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[   16.678623] PCI: bus1 uses PCIe port 1
[   16.678846] PCI host bridge to bus 0000:01
[   16.678864] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[   16.678878] pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
[   16.678891] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[   16.678928] PCI: bus1: Fast back to back transfers enabled
[   16.678942] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[   16.703122] bio: create slab <bio-0> at 0
[   16.872015] raid6: int32x1     95 MB/s
[   17.041012] raid6: int32x2    123 MB/s
[   17.211080] raid6: int32x4    120 MB/s
[   17.380943] raid6: int32x8    128 MB/s
[   17.380953] raid6: using algorithm int32x8 (128 MB/s)
[   17.380961] raid6: using intx1 recovery algorithm
[   17.381795] SCSI subsystem initialized
[   17.382248] libata version 3.00 loaded.
[   17.383134] usbcore: registered new interface driver usbfs
[   17.383310] usbcore: registered new interface driver hub
[   17.383506] usbcore: registered new device driver usb
[   17.385980] cfg80211: Calling CRDA to update world regulatory domain
[   17.386245] Switched to clocksource orion_clocksource
[   17.388512] NET: Registered protocol family 2
[   17.388982] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[   17.389041] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[   17.389092] TCP: Hash tables configured (established 4096 bind 4096)
[   17.389146] TCP: reno registered
[   17.389159] UDP hash table entries: 256 (order: 0, 4096 bytes)
[   17.389181] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[   17.389373] NET: Registered protocol family 1
[   17.389643] RPC: Registered named UNIX socket transport module.
[   17.389653] RPC: Registered udp transport module.
[   17.389661] RPC: Registered tcp transport module.
[   17.389668] RPC: Registered tcp NFSv4.1 backchannel transport module.
[   17.389689] PCI: CLS 32 bytes, default 32
[   17.536291] NetWinder Floating Point Emulator V0.97 (double precision)
[   17.536417] gpio-usb-probe-4b err=0
[   17.536432] gpio-usb gpio-usb: USB GPIO's initialized
[   17.538027] futex hash table entries: 256 (order: -1, 3072 bytes)
[   17.639678] VFS: Disk quotas dquot_6.5.2
[   17.639727] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[   17.640159] NFS: Registering the id_resolver key type
[   17.640237] Key type id_resolver registered
[   17.640247] Key type id_legacy registered
[   17.640264] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[   17.640277] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[   17.640378] NTFS driver 2.1.30 [Flags: R/W].
[   17.640409] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[   17.640555] fuse init (API version 7.22)
[   17.641183] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[   17.641598] msgmni has been set to 995
[   17.642716] async_tx: api initialized (async)
[   17.642903] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[   17.642915] io scheduler noop registered
[   17.642924] io scheduler deadline registered
[   17.642943] io scheduler cfq registered (default)
[   17.643324] mv_xor mv_xor.0: Marvell shared XOR driver
[   17.680878] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   17.720875] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[   17.721126] mv_xor mv_xor.1: Marvell shared XOR driver
[   17.760873] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   17.800873] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[   17.806755] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[   17.827867] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[   18.453917] console [ttyS0] enabled
[   18.466796] brd: module loaded
[   18.474502] loop: module loaded
[   18.477938] Uniform Multi-Platform E-IDE driver
[   18.482813] ide-gd driver 1.18
[   18.487365] sata_mv sata_mv.0: version 1.28
[   18.487428] sata_mv sata_mv.0: cannot get optional clkdev
[   18.493263] sata_mv sata_mv.0: slots 32 ports 2
[   18.500806] scsi0 : sata_mv
[   18.504318] scsi1 : sata_mv
[   18.507511] ata1: SATA max UDMA/133 irq 21
[   18.511710] ata2: SATA max UDMA/133 irq 21
[   18.517958] nand: Could not find valid ONFI parameter page; aborting
[   18.524399] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[   18.530724] nand: Hynix NAND 256MiB 3,3V 8-bit
[   18.535253] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[   18.540934] Scanning device for bad blocks
[   18.571874] Bad eraseblock 337 at 0x000002a20000
[   18.712526] Creating 3 MTD partitions on "orion_nand":
[   18.717646] 0x000000000000-0x000000100000 : "u-boot"
[   18.723748] 0x000000100000-0x000001100000 : "uImage"
[   18.729771] 0x000001100000-0x000010000000 : "root"
[   18.737715] tun: Universal TUN/TAP device driver, 1.6
[   18.742811] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[   18.749155] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   18.757543] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[   18.773899] libphy: orion_mdio_bus: probed
[   18.778145] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[   19.020847] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   19.040842] ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   19.102486] ata1.00: hard resetting link
[   19.451600] ata1.01: hard resetting link
[   19.811595] ata1.02: hard resetting link
[   19.901093] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:92:5c:4b
[   20.331102] ata1.03: hard resetting link
[   20.750876] ata1.02: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[   20.757118] ata1.02: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   20.860881] ata1.02: configured for UDMA/133
[   20.870928] ata1: EH complete
[   20.891157] scsi 0:2:0:0: Direct-Access     ATA      ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[   20.911353] fvdw1 disk index before get_sd_name = 0
[   20.916210] device-name= sata_mv
[   20.919424] fvdw2 disk index after get_sd_name = 1
[   20.940839] fvdw3 prefix[0]=s  prefix[1]=d
[   20.944912] fvdw4 diskname = sdb
[   20.948489] sd 0:2:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   20.961174] sd 0:2:0:0: Attached scsi generic sg0 type 0
[   20.966696] sd 0:2:0:0: [sdb] 4096-byte physical blocks
[   20.981285] sd 0:2:0:0: [sdb] Write Protect is off
[   20.986062] sd 0:2:0:0: [sdb] Mode Sense: 00 3a 00 00
[   20.990940] sd 0:2:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   21.075812]  sdb: sdb8
[   21.078900] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:4b:92:5c:4c
[   21.088523] sd 0:2:0:0: [sdb] Attached SCSI disk
[   21.093332] PPP generic driver version 2.4.2
[   21.097908] PPP Deflate Compression module registered
[   21.103050] PPP MPPE Compression module registered
[   21.107821] NET: Registered protocol family 24
[   21.112493] usbcore: registered new interface driver rtl8187
[   21.118128] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[   21.125693] usbcore: registered new interface driver pegasus
[   21.131548] usbcore: registered new interface driver asix
[   21.137095] usbcore: registered new interface driver ax88179_178a
[   21.143328] usbcore: registered new interface driver cdc_ether
[   21.149308] usbcore: registered new interface driver net1080
[   21.155116] usbcore: registered new interface driver cdc_subset
[   21.161235] usbcore: registered new interface driver zaurus
[   21.166977] usbcore: registered new interface driver ipheth
[   21.172714] usbcore: registered new interface driver cdc_ncm
[   21.179322] aoe: cannot create debugfs directory
[   21.184103] aoe: AoE v85 initialised.
[   21.188495] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   21.194563] i2c /dev entries driver
[   21.199035] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[   21.218481] md: linear personality registered for level -1
[   21.224011] md: raid0 personality registered for level 0
[   21.229298] md: raid1 personality registered for level 1
[   21.234660] md: raid10 personality registered for level 10
[   21.240261] md: raid6 personality registered for level 6
[   21.245589] md: raid5 personality registered for level 5
[   21.250897] md: raid4 personality registered for level 4
[   21.256380] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[   21.265023] device-mapper: multipath: version 1.6.0 loaded
[   21.270487] device-mapper: multipath round-robin: version 1.0.0 loaded
[   21.277028] device-mapper: multipath queue-length: version 0.1.0 loaded
[   21.283634] device-mapper: multipath service-time: version 0.2.0 loaded
[   21.290280] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   21.296381] device-mapper: raid: Loading target version 1.5.2
[   21.306233] ipip: IPv4 over IPv4 tunneling driver
[   21.311731] TCP: cubic registered
[   21.315073] NET: Registered protocol family 10
[   21.320460] sit: IPv6 over IPv4 tunneling driver
[   21.325955] NET: Registered protocol family 17
[   21.330634] NET: Registered protocol family 5
[   21.335312] 8021q: 802.1Q VLAN Support v1.8
[   21.339509] NET: Registered protocol family 37
[   21.344084] Key type dns_resolver registered
[   21.349531] netpoll: netconsole: local port 6666
[   21.354196] netpoll: netconsole: local IPv4 address 192.168.1.252
[   21.360263] netpoll: netconsole: interface 'eth0'
[   21.364977] netpoll: netconsole: remote port 6666
[   21.369656] netpoll: netconsole: remote IPv4 address 192.168.1.2
[   21.375705] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   21.382683] netpoll: netconsole: device eth0 not up yet, forcing it
[   21.490852] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   21.510842] ata2.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   21.572475] ata2.00: hard resetting link
[   21.921599] ata2.01: hard resetting link
[   22.281598] ata2.02: hard resetting link
[   22.500566] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   22.641600] ata2.03: hard resetting link
[   22.991749] ata2: EH complete
[   25.150218] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   25.160037] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   25.169556] console [netcon0] enabled
[   25.173267] netconsole: network logging started
[   25.178266] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   25.185386] rtc-mv rtc-mv: setting system clock to 2020-12-06 21:43:16 UTC (1607290996)
[   25.199253] Freeing unused kernel memory: 1932K (c0767000 - c094a000)
[   26.290781] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   35.379231] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   35.389599] ehci-orion: EHCI orion driver
[   35.393822] orion-ehci orion-ehci.0: EHCI Host Controller
[   35.399247] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   35.406963] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   35.430854] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   35.436894] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   35.443701] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   35.450925] usb usb1: Product: EHCI Host Controller
[   35.455795] usb usb1: Manufacturer: Linux 3.14.2 ehci_hcd
[   35.461203] usb usb1: SerialNumber: orion-ehci.0
[   35.466525] hub 1-0:1.0: USB hub found
[   35.470331] hub 1-0:1.0: 1 port detected
[   35.480766] usbcore: registered new interface driver usb-storage
[   35.790863] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   35.941356] usb 1-1: New USB device found, idVendor=0424, idProduct=2512
[   35.948062] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   35.955999] hub 1-1:1.0: USB hub found
[   35.959845] hub 1-1:1.0: 2 ports detected
root@fvdw-sta-kirkwood:/ #

i tried to boot to slot 2 and it is installing

[fvdw]

oke thank you

i tried to boot to slot 2 and it is installing

Yes it will install but the firmware won't run as it will look for sda which is not present.

I looked at dmesg output with disks in slot 2,3,4 and 5

I see
sdb on bus 0:2:0:0 (slot 2)
sdc on bus 0:1:0:0 (slot 3)
sdd on bus 1:2:00 (slot 4)

I am missing
sda on bus 0:3:0:0 (slot1 ) <--expected as it is defect
sde on bus 1:1:0:0 (slot 5) <--- not expected

It seems slot 5 is also not functional, but this could be a defective disk.
Please put another disk in slot 5 to and start alone kernel and list output of dmesg to see if the slot is working with another disk.
If not then you have two defective slots on your 5big2 and we can only use the three slots 2,3 and 4

[taetae]

oke thank you

i tried to boot to slot 2 and it is installing

Yes it will install but the firmware won't run as it will look for sda which is not present.

I looked at dmesg output with disks in slot 2,3,4 and 5

I see
sdb on bus 0:2:0:0 (slot 2)
sdc on bus 0:1:0:0 (slot 3)
sdd on bus 1:2:00 (slot 4)

I am missing
sda on bus 0:3:0:0 (slot1 ) <--expected as it is defect
sde on bus 1:1:0:0 (slot 5) <--- not expected

It seems slot 5 is also not functional, but this could be a defective disk.
Please put another disk in slot 5 to and start alone kernel and list output of dmesg to see if the slot is working with another disk.
If not then you have two defective slots on your 5big2 and we can only use the three slots 2,3 and 4

ok inserted only in slot 5 and 2

Code: Select all

root@fvdw-sta-kirkwood:/ # dmesg
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #171 PREEMPT Wed Jan 17 23:33:31 CET 2018
[    0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie 5Big Network Nand v2
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] On node 0 totalpages: 131072
[    0.000000] free_area_init_node: node 0, pgdat c0982898, node_mem_map dfbfb000
[    0.000000]   Normal zone: 1024 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 131072 pages, LIFO batch:31
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 130048
[    0.000000] Kernel command line: console=ttyS0,115200 netconsole=6666@192.168.1.252/,6666@192.168.1.2/ cap=gpt,lba64
[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.000000] Memory: 509780K/524288K available (5950K kernel code, 220K rwdata, 1596K rodata, 1933K init, 233K bss, 14508K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xe0800000 - 0xff000000   ( 488 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xe0000000   ( 512 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0766b44   (7547 kB)
[    0.000000]       .init : 0xc0767000 - 0xc094a4cc   (1934 kB)
[    0.000000]       .data : 0xc094c000 - 0xc0983100   ( 221 kB)
[    0.000000]        .bss : 0xc098310c - 0xc09bd56c   ( 234 kB)
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:114
[    0.000012] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[    6.215038] Calibrating delay loop... 1196.85 BogoMIPS (lpj=5984256)
[    6.305009] pid_max: default: 32768 minimum: 301
[    6.305144] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    6.305162] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    6.305707] CPU: Testing write buffer coherency: ok
[    6.306017] Setting up static identity map for 0x5a6ac0 - 0x5a6b18
[    6.308649] VFP support v0.3: not present
[    6.309183] xor: measuring software checksum speed
[    6.405041]    arm4regs  :  1089.200 MB/sec
[    6.505002]    8regs     :   654.400 MB/sec
[    6.604993]    32regs    :   905.600 MB/sec
[    6.605010] xor: using function: arm4regs (1089.200 MB/sec)
[    6.605027] pinctrl core: initialized pinctrl subsystem
[    6.605143] NET: Registered protocol family 16
[    6.605524] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    6.608255] Kirkwood: MV88F6281-A1, TCLK=166666667.
[    6.608280] Feroceon L2: Enabling L2
[    6.608318] Feroceon L2: Cache support initialised.
[    6.609408] mv_usb_init 1
[    6.609426] mv_usb_init 2 devnum = 0
[    6.609438] init function mv_usb_init finished
[    6.609446] initial MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[    6.609478]   final MPP regs: 01111111 00003311 33331100 33003333 00000033 00000000 00000000
[    6.609664]  orion-ehci registered
[    6.611492] orion_gpio_is_valid: invalid GPIO 7
[    6.611996] Kirkwood PCIe port 0: link down
[    6.612006] Kirkwood PCIe port 1: link up
[    6.612015] PCI: bus0 uses PCIe port 0
[    6.612256] PCI host bridge to bus 0000:00
[    6.612277] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe7ffffff]
[    6.612291] pci_bus 0000:00: root bus resource [io  0x1000-0xffff]
[    6.612304] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[    6.612352] pci 0000:00:00.0: [11ab:6281] type 00 class 0x058000
[    6.612381] pci 0000:00:00.0: reg 0x10: [mem 0xf1000000-0xf10fffff 64bit pref]
[    6.612399] pci 0000:00:00.0: reg 0x18: [mem 0x00000000-0x1fffffff]
[    6.612450] pci 0000:00:00.0: supports D1 D2
[    6.612726] PCI: bus0: Fast back to back transfers disabled
[    6.612744] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00
[    6.612757] PCI: bus1 uses PCIe port 1
[    6.612979] PCI host bridge to bus 0000:01
[    6.612997] pci_bus 0000:01: root bus resource [mem 0xe8000000-0xefffffff]
[    6.613011] pci_bus 0000:01: root bus resource [io  0x10000-0x1ffff]
[    6.613023] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[    6.613061] PCI: bus1: Fast back to back transfers enabled
[    6.613075] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    6.637265] bio: create slab <bio-0> at 0
[    6.806171] raid6: int32x1     95 MB/s
[    6.975151] raid6: int32x2    123 MB/s
[    7.145222] raid6: int32x4    120 MB/s
[    7.315090] raid6: int32x8    128 MB/s
[    7.315100] raid6: using algorithm int32x8 (128 MB/s)
[    7.315108] raid6: using intx1 recovery algorithm
[    7.315939] SCSI subsystem initialized
[    7.316393] libata version 3.00 loaded.
[    7.317278] usbcore: registered new interface driver usbfs
[    7.317453] usbcore: registered new interface driver hub
[    7.317646] usbcore: registered new device driver usb
[    7.320118] cfg80211: Calling CRDA to update world regulatory domain
[    7.320383] Switched to clocksource orion_clocksource
[    7.322650] NET: Registered protocol family 2
[    7.323118] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
[    7.323176] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[    7.323228] TCP: Hash tables configured (established 4096 bind 4096)
[    7.323280] TCP: reno registered
[    7.323293] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    7.323315] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    7.323506] NET: Registered protocol family 1
[    7.323773] RPC: Registered named UNIX socket transport module.
[    7.323785] RPC: Registered udp transport module.
[    7.323792] RPC: Registered tcp transport module.
[    7.323799] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    7.323820] PCI: CLS 32 bytes, default 32
[    7.470394] NetWinder Floating Point Emulator V0.97 (double precision)
[    7.470520] gpio-usb-probe-4b err=0
[    7.470535] gpio-usb gpio-usb: USB GPIO's initialized
[    7.472136] futex hash table entries: 256 (order: -1, 3072 bytes)
[    7.573784] VFS: Disk quotas dquot_6.5.2
[    7.573833] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    7.574264] NFS: Registering the id_resolver key type
[    7.574311] Key type id_resolver registered
[    7.574321] Key type id_legacy registered
[    7.574338] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    7.574352] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    7.574454] NTFS driver 2.1.30 [Flags: R/W].
[    7.574484] jffs2: version 2.2. (NAND) (SUMMARY)  © 2001-2006 Red Hat, Inc.
[    7.574630] fuse init (API version 7.22)
[    7.575250] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[    7.575664] msgmni has been set to 995
[    7.576779] async_tx: api initialized (async)
[    7.576964] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    7.576976] io scheduler noop registered
[    7.576984] io scheduler deadline registered
[    7.577004] io scheduler cfq registered (default)
[    7.577386] mv_xor mv_xor.0: Marvell shared XOR driver
[    7.615020] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    7.655017] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[    7.655267] mv_xor mv_xor.1: Marvell shared XOR driver
[    7.695015] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    7.735015] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
[    7.740910] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    7.762025] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33, base_baud = 10416666) is a 16550A
[    8.388063] console [ttyS0] enabled
[    8.400946] brd: module loaded
[    8.408655] loop: module loaded
[    8.412097] Uniform Multi-Platform E-IDE driver
[    8.416968] ide-gd driver 1.18
[    8.421524] sata_mv sata_mv.0: version 1.28
[    8.421587] sata_mv sata_mv.0: cannot get optional clkdev
[    8.427417] sata_mv sata_mv.0: slots 32 ports 2
[    8.434959] scsi0 : sata_mv
[    8.438471] scsi1 : sata_mv
[    8.441661] ata1: SATA max UDMA/133 irq 21
[    8.445856] ata2: SATA max UDMA/133 irq 21
[    8.452097] nand: Could not find valid ONFI parameter page; aborting
[    8.458537] nand: device found, Manufacturer ID: 0xad, Chip ID: 0xda
[    8.464863] nand: Hynix NAND 256MiB 3,3V 8-bit
[    8.469393] nand: 256MiB, SLC, page size: 2048, OOB size: 64
[    8.475073] Scanning device for bad blocks
[    8.506013] Bad eraseblock 337 at 0x000002a20000
[    8.646674] Creating 3 MTD partitions on "orion_nand":
[    8.651793] 0x000000000000-0x000000100000 : "u-boot"
[    8.657893] 0x000000100000-0x000001100000 : "uImage"
[    8.663907] 0x000001100000-0x000010000000 : "root"
[    8.671853] tun: Universal TUN/TAP device driver, 1.6
[    8.676950] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    8.683294] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[    8.691682] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[    8.708045] libphy: orion_mdio_bus: probed
[    8.712289] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.954989] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[    8.975068] ata1.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[    9.036567] ata1.00: hard resetting link
[    9.385744] ata1.01: hard resetting link
[    9.745738] ata1.02: hard resetting link
[    9.835283] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:92:5c:4b
[   10.265245] ata1.03: hard resetting link
[   10.685018] ata1.02: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[   10.691256] ata1.02: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   10.795024] ata1.02: configured for UDMA/133
[   10.805070] ata1: EH complete
[   10.825304] scsi 0:2:0:0: Direct-Access     ATA      ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[   10.845494] fvdw1 disk index before get_sd_name = 0
[   10.850348] device-name= sata_mv
[   10.853563] fvdw2 disk index after get_sd_name = 1
[   10.874981] fvdw3 prefix[0]=s  prefix[1]=d
[   10.879059] fvdw4 diskname = sdb
[   10.882623] sd 0:2:0:0: [sdb] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   10.895317] sd 0:2:0:0: Attached scsi generic sg0 type 0
[   10.900849] sd 0:2:0:0: [sdb] 4096-byte physical blocks
[   10.915426] sd 0:2:0:0: [sdb] Write Protect is off
[   10.920201] sd 0:2:0:0: [sdb] Mode Sense: 00 3a 00 00
[   10.925082] sd 0:2:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   11.002359]  sdb: sdb8
[   11.012318] sd 0:2:0:0: [sdb] Attached SCSI disk
[   11.018396] mv643xx_eth_port mv643xx_eth_port.1 eth1: port 0 with MAC address 00:d0:4b:92:5c:4c
[   11.027286] PPP generic driver version 2.4.2
[   11.031863] PPP Deflate Compression module registered
[   11.036989] PPP MPPE Compression module registered
[   11.041759] NET: Registered protocol family 24
[   11.046395] usbcore: registered new interface driver rtl8187
[   11.052034] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[   11.059588] usbcore: registered new interface driver pegasus
[   11.065429] usbcore: registered new interface driver asix
[   11.070973] usbcore: registered new interface driver ax88179_178a
[   11.077213] usbcore: registered new interface driver cdc_ether
[   11.083189] usbcore: registered new interface driver net1080
[   11.088998] usbcore: registered new interface driver cdc_subset
[   11.095106] usbcore: registered new interface driver zaurus
[   11.100809] usbcore: registered new interface driver ipheth
[   11.106598] usbcore: registered new interface driver cdc_ncm
[   11.113198] aoe: cannot create debugfs directory
[   11.117993] aoe: AoE v85 initialised.
[   11.122381] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[   11.128418] i2c /dev entries driver
[   11.132888] at24 0-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write
[   11.152317] md: linear personality registered for level -1
[   11.157890] md: raid0 personality registered for level 0
[   11.163178] md: raid1 personality registered for level 1
[   11.168547] md: raid10 personality registered for level 10
[   11.174152] md: raid6 personality registered for level 6
[   11.179477] md: raid5 personality registered for level 5
[   11.184761] md: raid4 personality registered for level 4
[   11.190269] device-mapper: ioctl: 4.27.0-ioctl (2013-10-30) initialised: dm-devel@redhat.com
[   11.198910] device-mapper: multipath: version 1.6.0 loaded
[   11.204374] device-mapper: multipath round-robin: version 1.0.0 loaded
[   11.210916] device-mapper: multipath queue-length: version 0.1.0 loaded
[   11.217521] device-mapper: multipath service-time: version 0.2.0 loaded
[   11.224169] device-mapper: dm-log-userspace: version 1.3.0 loaded
[   11.230269] device-mapper: raid: Loading target version 1.5.2
[   11.240121] ipip: IPv4 over IPv4 tunneling driver
[   11.245621] TCP: cubic registered
[   11.248961] NET: Registered protocol family 10
[   11.254348] sit: IPv6 over IPv4 tunneling driver
[   11.259841] NET: Registered protocol family 17
[   11.264520] NET: Registered protocol family 5
[   11.269193] 8021q: 802.1Q VLAN Support v1.8
[   11.273389] NET: Registered protocol family 37
[   11.277932] Key type dns_resolver registered
[   11.283404] netpoll: netconsole: local port 6666
[   11.288067] netpoll: netconsole: local IPv4 address 192.168.1.252
[   11.294134] netpoll: netconsole: interface 'eth0'
[   11.298849] netpoll: netconsole: remote port 6666
[   11.303535] netpoll: netconsole: remote IPv4 address 192.168.1.2
[   11.309583] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[   11.316564] netpoll: netconsole: device eth0 not up yet, forcing it
[   11.424993] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[   11.445068] ata2.15: Port Multiplier 1.2, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[   11.506547] ata2.00: hard resetting link
[   11.865742] ata2.01: hard resetting link
[   12.385242] ata2.02: hard resetting link
[   12.434712] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   12.745742] ata2.03: hard resetting link
[   13.155024] ata2.01: ATA-10: ST2000DM008-2FR102, 0001, max UDMA/133
[   13.161268] ata2.01: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   13.245027] ata2.01: configured for UDMA/133
[   13.249463] ata2: EH complete
[   13.265256] scsi 1:1:0:0: Direct-Access     ATA      ST2000DM008-2FR1 0001 PQ: 0 ANSI: 5
[   13.273808] fvdw1 disk index before get_sd_name = 1
[   13.278720] device-name= sata_mv
[   13.281931] fvdw2 disk index after get_sd_name = 4
[   13.286726] fvdw3 prefix[0]=s  prefix[1]=d
[   13.290803] fvdw4 diskname = sde
[   13.294491] sd 1:1:0:0: [sde] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[   13.302547] sd 1:1:0:0: Attached scsi generic sg1 type 0
[   13.307926] sd 1:1:0:0: [sde] 4096-byte physical blocks
[   13.313700] sd 1:1:0:0: [sde] Write Protect is off
[   13.318675] sd 1:1:0:0: [sde] Mode Sense: 00 3a 00 00
[   13.318795] sd 1:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[   13.376336]  sde: sde1 sde2 sde3 sde4 < sde5 sde6 sde7 sde8 >
[   13.384848] sd 1:1:0:0: [sde] Attached SCSI disk
[   15.172414] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[   15.182239] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   15.191952] console [netcon0] enabled
[   15.195667] netconsole: network logging started
[   15.200655] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[   15.207782] rtc-mv rtc-mv: setting system clock to 2020-12-06 22:20:54 UTC (1607293254)
[   15.221626] Freeing unused kernel memory: 1932K (c0767000 - c094a000)
[   16.314909] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[   25.403468] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[   25.413726] ehci-orion: EHCI orion driver
[   25.417938] orion-ehci orion-ehci.0: EHCI Host Controller
[   25.423366] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[   25.431086] orion-ehci orion-ehci.0: irq 19, io mem 0xf1050000
[   25.454996] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[   25.461045] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[   25.467851] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[   25.475074] usb usb1: Product: EHCI Host Controller
[   25.479945] usb usb1: Manufacturer: Linux 3.14.2 ehci_hcd
[   25.485353] usb usb1: SerialNumber: orion-ehci.0
[   25.490670] hub 1-0:1.0: USB hub found
[   25.494479] hub 1-0:1.0: 1 port detected
[   25.504925] usbcore: registered new interface driver usb-storage
[   25.815006] usb 1-1: new high-speed USB device number 2 using orion-ehci
[   25.965481] usb 1-1: New USB device found, idVendor=0424, idProduct=2512
[   25.972209] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   25.980140] hub 1-1:1.0: USB hub found
[   25.983970] hub 1-1:1.0: 2 ports detected
root@fvdw-sta-kirkwood:/ #

what could make slot 1 not work ??

I thank you for the help you are giving me and I will read your answers tomorrow because I have to go to work and I will be back tomorrow in the evening