In case anybody needs to start with fully erased or completely new drives, here's what you need:
I managed to create an clean
image with LaCix Linux version 2.2.10.1 from scratch you can dd to your first drive of (almost) any size.
+ Any number of additional drives (0 to 4) only need to be unformatted (no partition table at all).
+ No need to copy anything on those drives.
+ All necessary stuff will be copied at first boot from your first drive (slot 1, /dev/sda).
+ Autoadjusting user space to disks maximum.
+ Full version - no updates applied at all (till now).
I guess there will be a size limit of 2 TB because of its type of partition table.
(Had no drives over 2 TB handy - a GPT might help?!)
:mrgreen:
Hope this helps!
This is what you get at first boot with one imaged and four fresh 1 TB drives:
- Code: Select all
_ ____ _
| | __ _ / ___(_) ___
| | / _` | | | |/ _ \
| |___ (_| | |___| | __/
|_____\__,_|\____|_|\___|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: 5BIG LE
Hold front button - long : FAIL
U-Boot 1.1.4 (Mar 16 2010 - 09:12:35) Marvell version: 3.4.16 LaCie 1.4.4
U-Boot code: 00600000 -> 006701D0 BSS: -> 006BDE80
Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 166Mhz
DRAM CAS Latency = 6 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000 size 256MB
DRAM CS[1] base 0x10000000 size 256MB
DRAM Total size 512MB 16bit width
[512kB@f8000000] Flash: 512 kB
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
CPU : Marvell Feroceon (Rev 1)
Streaming disabled
Write allocate disabled
Module 0 is RGMII
USB 0: host mode
PEX 0: interface detected no Link.
Net: egiga0 [PRIME], egiga1
Waiting for LUMP (3)
no lump receive; continuing
Hit any key to stop autoboot: 0
Reset IDE:
Marvell Serial ATA Adapter
Integrated Sata device found
Port Multiplier found @ 0 0. Vendor: 11ab ports: 4
[0 0 1]: Enable DMA mode
Device 1 @ 0 0 1:
Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: S2C4J9BZ823299
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 0 2]: Enable DMA mode
Device 2 @ 0 0 2:
Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: S2C4J9BZ823058
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 0 3]: Enable DMA mode
Device 3 @ 0 0 3:
Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: S2C4J9CZ900098
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
Port Multiplier found @ 0 1. Vendor: 11ab ports: 4
[0 1 1]: Enable DMA mode
Device 5 @ 0 1 1:
Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: S2C4J9BZ823320
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
[0 1 2]: Enable DMA mode
Device 6 @ 0 1 2:
Model: SAMSUNG HD103SI Firm: 1AG01118 Ser#: S2C4J9BZ823282
Type: Hard Disk
Supports 48-bit addressing
Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512)
## Valid DOS partition found ##
Loading from IDE device 3, partition 10: Name: hdd10
Type: U-Boot
** Bad Magic Number **
## Valid DOS partition found ##
Loading from IDE device 3, partition 6: Name: hdd6
Type: U-Boot
Image Name: Linux kernel-2.6.31.14-svn6790 [
Created: 2014-11-14 21:13:59 UTC
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5548501 Bytes = 5.3 MB
Load Address: 00008000
Entry Point: 00008000
Contents:
Image 0: 3003928 Bytes = 2.9 MB
Image 1: 2544561 Bytes = 2.4 MB
## Booting image at 00800000 ...
Image Name: Linux kernel-2.6.31.14-svn6790 [
Created: 2014-11-14 21:13:59 UTC
Image Type: ARM Linux Multi-File Image (uncompressed)
Data Size: 5548501 Bytes = 5.3 MB
Load Address: 00008000
Entry Point: 00008000
Contents:
Image 0: 3003928 Bytes = 2.9 MB
Image 1: 2544561 Bytes = 2.4 MB
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux................................................................................................................................................................................................. done, booting the kernel.
[ 0.000000] Linux version 2.6.31.14-svn6790 (sbs@node2.lacie.com) (gcc version 4.2.1) #1 Fri Nov 14 20:31:45 UTC 2014
[ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 (ARMv5TE), cr=00053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: net5big_v2
[ 0.000000] Using UBoot passing parameters structure
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro reset=0 productType=BIG5_KW
[ 0.000000] PID hash table entries: 2048 (order: 11, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 256MB 256MB = 512MB total
[ 0.000000] Memory: 510592KB available (5420K code, 377K data, 148K init, 0K highmem)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:128
[ 0.000000] Console: colour dummy device 80x30
[ 0.000000] Calibrating delay loop... 1199.30 BogoMIPS (lpj=5996544)
[ 0.230000] Mount-cache hash table entries: 512
[ 0.230000] CPU: Testing write buffer coherency: ok
[ 0.230000] xor: measuring software checksum speed
[ 0.280000] arm4regs : 1024.800 MB/sec
[ 0.330000] 8regs : 827.200 MB/sec
[ 0.380000] 32regs : 926.800 MB/sec
[ 0.380000] xor: using function: arm4regs (1024.800 MB/sec)
[ 0.380000] NET: Registered protocol family 16
[ 0.380000] Feroceon L2: Enabling L2
[ 0.380000] Feroceon L2: Cache support initialised.
[ 0.380000]
[ 0.380000] CPU Interface
[ 0.380000] -------------
[ 0.380000] SDRAM_CS0 ....base 00000000, size 256MB
[ 0.380000] SDRAM_CS1 ....base 10000000, size 256MB
[ 0.380000] SDRAM_CS2 ....disable
[ 0.380000] SDRAM_CS3 ....disable
[ 0.380000] PEX0_MEM ....base e8000000, size 128MB
[ 0.380000] PEX0_IO ....base f2000000, size 1MB
[ 0.380000] INTER_REGS ....base f1000000, size 1MB
[ 0.380000] NFLASH_CS ....base fa000000, size 2MB
[ 0.380000] SPI_CS ....base f4000000, size 16MB
[ 0.380000] BOOT_ROM_CS ....no such
[ 0.380000] DEV_BOOTCS ....no such
[ 0.380000] CRYPT_ENG ....base f0000000, size 2MB
[ 0.380000]
[ 0.380000] Marvell Development Board (LSP Version KW_LSP_5.0.3)-- net5big_v2 Soc: 88F6281 A0 LE
[ 0.380000]
[ 0.380000] Detected Tclk 166666667 and SysClk 400000000
[ 0.380000] Register Marvell USB EHCI Host controller #0
[ 0.390000] bio: create slab <bio-0> at 0
[ 0.390000] SCSI Scattered Spinup: Enabled
[ 0.390000] o Maximum Disk Spinup: 1
[ 0.390000] o Disk Spinup timeout: 10
[ 0.390000] SCSI subsystem initialized
[ 0.560000] raid6: int32x1 91 MB/s
[ 0.730000] raid6: int32x2 107 MB/s
[ 0.900000] raid6: int32x4 123 MB/s
[ 1.070000] raid6: int32x8 108 MB/s
[ 1.070000] raid6: using algorithm int32x4 (123 MB/s)
[ 1.070000] NET: Registered protocol family 2
[ 1.070000] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 1.070000] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 1.070000] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 1.070000] TCP: Hash tables configured (established 16384 bind 16384)
[ 1.070000] TCP reno registered
[ 1.070000] NET: Registered protocol family 1
[ 1.070000] Trying to unpack rootfs image as initramfs...
[ 1.080000] Switched to NOHz mode on CPU #0
[ 1.230000] Freeing initrd memory: 2484K
[ 1.230000] cpufreq: Init kirkwood cpufreq driver
[ 1.250000] cesadev_init(c000ee90)
[ 1.250000] mvCesaInit: sessions=640, queue=64, pSram=f0000000
[ 1.250000] gpio-hd-power gpio-hd-power: GPIO Hard Disk power device initialized
[ 1.250000] gpio-usb gpio-usb: USB GPIO's initialized
[ 1.250000] g762 0-003e: found a platform specific fan speed array
[ 1.250000] g762 0-003e: device successfully initialized
[ 1.250000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 1.250000] Registering unionfs 2.5.10 (for 2.6.31.14)
[ 1.250000] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1.250000] JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[ 1.260000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled
[ 1.260000] SGI XFS Quota Management subsystem
[ 1.260000] msgmni has been set to 1002
[ 1.260000] alg: No test for cipher_null (cipher_null-generic)
[ 1.260000] alg: No test for ecb(cipher_null) (ecb-cipher_null)
[ 1.260000] alg: No test for digest_null (digest_null-generic)
[ 1.260000] alg: No test for compress_null (compress_null-generic)
[ 1.260000] alg: No test for stdrng (krng)
[ 1.270000] alg: No test for hmac(digest_null) (hmac(digest_null-generic))
[ 1.270000] async_tx: api initialized (async)
[ 1.270000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 1.270000] io scheduler noop registered
[ 1.270000] io scheduler anticipatory registered (default)
[ 1.270000] io scheduler deadline registered
[ 1.270000] io scheduler cfq registered
[ 1.290000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.290000] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) is a 16550A
[ 1.290000] console [ttyS0] enabled
[ 1.770000] brd: module loaded
[ 1.780000] at24 0-0050: 512 byte 24c04 EEPROM (writable)
[ 1.780000] sata_mv sata_mv.0: version 1.28
[ 1.790000] sata_mv sata_mv.0: slots 32 ports 2
[ 1.790000] scsi0 : sata_mv
[ 1.800000] scsi1 : sata_mv
[ 1.800000] ata1: SATA max UDMA/133 irq 21
[ 1.800000] ata2: SATA max UDMA/133 irq 21
[ 1.810000] INIT Marvell Ethernet Driver: mv_netdev
[ 1.810000] Loading Marvell Ethernet Driver:
[ 1.820000] o Cached descriptors in DRAM
[ 1.820000] o DRAM SW cache-coherency
[ 1.820000] o 2 Giga ports supported
[ 1.830000] o Single RX Queue support - ETH_DEF_RXQ=0
[ 1.830000] o Single TX Queue support - ETH_DEF_TXQ=0
[ 1.840000] o TCP segmentation offload (TSO) supported
[ 1.840000] o Large Receive offload (LRO) supported
[ 1.850000] o Receive checksum offload supported
[ 1.850000] o Transmit checksum offload supported
[ 1.860000] o Network Fast Processing (Routing) supported - (Disabled)
[ 1.870000] o Proc tool API enabled
[ 1.870000] o SKB Reuse supported - (Disabled)
[ 1.870000] o SKB Recycle supported - (Disabled)
[ 1.880000] o Rx descripors: q0=128
[ 1.880000] o Tx descripors: q0=532
[ 1.890000] o Loading network interface(s):
[ 1.890000] o register under mv_netdev platform
[ 1.900000] o eth0, ifindex = 2, GbE port = 0
[ 1.900000] o eth1, ifindex = 3, GbE port = 1
[ 1.910000]
[ 1.910000] mvFpRuleDb (dffec000): 4096 entries, 16384 bytes
[ 1.910000] console [netcon0] enabled
[ 1.920000] netconsole: network logging started
[ 1.920000] m25p80 spi0.0: mx25l4005a (512 Kbytes)
[ 1.930000] Creating 1 MTD partitions on "spi_flash":
[ 1.930000] 0x000000000000-0x000000080000 : "u-boot"
[ 1.940000] mice: PS/2 mouse device common for all mice
[ 1.950000] input: gpio-keys as /devices/platform/gpio-keys/input/input0
[ 1.950000] rtc-mv rtc-mv: rtc core: registered rtc-mv as rtc0
[ 2.040000] md: linear personality registered for level -1
[ 2.040000] md: raid0 personality registered for level 0
[ 2.050000] md: raid1 personality registered for level 1
[ 2.050000] md: raid10 personality registered for level 10
[ 2.060000] md: raid6 personality registered for level 6
[ 2.060000] md: raid5 personality registered for level 5
[ 2.070000] md: raid4 personality registered for level 4
[ 2.070000] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 2.090000] cpuidle: using governor ladder
[ 2.090000] cpuidle: using governor menu
[ 2.090000] Registered led device: net5big-v2:blue:power
[ 2.100000] Registered led device: net5big-v2:red:power
[ 2.100000] Registered led device: net5big-v2:blue:sata0
[ 2.110000] Registered led device: net5big-v2:red:sata0
[ 2.120000] Registered led device: net5big-v2:blue:sata1
[ 2.120000] Registered led device: net5big-v2:red:sata1
[ 2.130000] Registered led device: net5big-v2:blue:sata2
[ 2.130000] Registered led device: net5big-v2:red:sata2
[ 2.140000] Registered led device: net5big-v2:blue:sata3
[ 2.140000] Registered led device: net5big-v2:red:sata3
[ 2.150000] Registered led device: net5big-v2:blue:sata4
[ 2.150000] Registered led device: net5big-v2:red:sata4
[ 2.160000] mv_xor_shared mv_xor_shared.0: Marvell shared XOR driver
[ 2.170000] mv_xor_shared mv_xor_shared.1: Marvell shared XOR driver
[ 2.210000] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
[ 2.250000] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
[ 2.290000] mv_xor mv_xor.2: Marvell XOR: ( xor cpy )
[ 2.330000] mv_xor mv_xor.3: Marvell XOR: ( xor fill cpy )
[ 2.330000] TCP cubic registered
[ 2.330000] NET: Registered protocol family 17
[ 2.340000] Bridge firewalling registered
[ 2.340000] NET: Registered protocol family 5
[ 2.350000] RPC: Registered udp transport module.
[ 2.350000] RPC: Registered tcp transport module.
[ 2.360000] rtc-mv rtc-mv: setting system clock to 2014-12-13 08:52:05 UTC (1418460725)
[ 2.390000] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 2.390000] ata1.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[ 2.400000] ata1.00: hard resetting link
[ 2.750000] ata1.01: hard resetting link
[ 3.260000] ata1.02: hard resetting link
[ 3.770000] ata1.03: hard resetting link
[ 4.300000] ata1.01: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
[ 4.300000] ata1.01: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.330000] ata1.01: configured for UDMA/133
[ 4.350000] ata1.02: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
[ 4.350000] ata1.02: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.380000] ata1.02: configured for UDMA/133
[ 4.400000] ata1.03: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
[ 4.400000] ata1.03: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 4.430000] ata1.03: configured for UDMA/133
[ 4.430000] ata1: EH complete
[ 4.430000] scsi 0:1:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
[ 4.440000] sd 0:1:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.450000] sd 0:1:0:0: [sdc] Write Protect is off
[ 4.450000] sd 0:1:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.460000] sdc:
[ 4.470000] sd 0:1:0:0: Attached scsi generic sg0 type 0
[ 4.470000] scsi 0:2:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
[ 4.480000] unknown partition table
[ 4.480000] sd 0:1:0:0: [sdc] Attached SCSI disk
[ 4.490000] sd 0:2:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.500000] sd 0:2:0:0: [sdb] Write Protect is off
[ 4.500000] sd 0:2:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.510000] sdb:
[ 4.510000] sd 0:2:0:0: Attached scsi generic sg1 type 0
[ 4.520000] scsi 0:3:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
[ 4.530000] unknown partition table
[ 4.530000] sd 0:2:0:0: [sdb] Attached SCSI disk
[ 4.540000] sd 0:3:0:0: [sda] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 4.550000] sd 0:3:0:0: [sda] Write Protect is off
[ 4.550000] sd 0:3:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 4.560000] sda:
[ 4.560000] sd 0:3:0:0: Attached scsi generic sg2 type 0
[ 4.570000] sda1 < sda5 sda6 sda7 sda8 sda9 sda10 >
[ 4.610000] sd 0:3:0:0: [sda] Attached SCSI disk
[ 5.080000] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 5.080000] ata2.15: Port Multiplier 1.1, 0x11ab:0x4140 r193, 4 ports, feat 0x5/0x1f
[ 5.090000] ata2.00: hard resetting link
[ 5.440000] ata2.01: hard resetting link
[ 5.950000] ata2.02: hard resetting link
[ 6.460000] ata2.03: hard resetting link
[ 6.830000] ata2.01: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
[ 6.830000] ata2.01: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 6.860000] ata2.01: configured for UDMA/133
[ 6.880000] ata2.02: ATA-7: SAMSUNG HD103SI, 1AG01118, max UDMA7
[ 6.880000] ata2.02: 1953525168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 6.910000] ata2.02: configured for UDMA/133
[ 6.910000] ata2: EH complete
[ 6.910000] scsi 1:1:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
[ 6.920000] sd 1:1:0:0: [sde] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 6.930000] sd 1:1:0:0: [sde] Write Protect is off
[ 6.930000] sd 1:1:0:0: [sde] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.940000] sde:
[ 6.950000] sd 1:1:0:0: Attached scsi generic sg3 type 0
[ 6.950000] scsi 1:2:0:0: Direct-Access ATA SAMSUNG HD103SI 1AG0 PQ: 0 ANSI: 5
[ 6.960000] unknown partition table
[ 6.960000] sd 1:1:0:0: [sde] Attached SCSI disk
[ 6.970000] sd 1:2:0:0: [sdd] 1953525168 512-byte logical blocks: (1.00 TB/931 GiB)
[ 6.980000] sd 1:2:0:0: [sdd] Write Protect is off
[ 6.980000] sd 1:2:0:0: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 6.990000] sdd:
[ 6.990000] sd 1:2:0:0: Attached scsi generic sg4 type 0
[ 7.000000] unknown partition table
[ 7.000000] sd 1:2:0:0: [sdd] Attached SCSI disk
[ 7.010000] Freeing init memory: 148K
[ 7.010000] Freeing initramfs memory: 4K
===INITRAMFS: =======================================INITRAMFS================================
===INITRAMFS: Initializing filesystem
===INITRAMFS: Mounting /proc
===INITRAMFS: Mounting /sys
===INITRAMFS: Populating /dev
===INITRAMFS: Mounting /dev/pts
===INITRAMFS: Product ID = 'net5big_v2'
===INITRAMFS: numRaidDevices=5
===INITRAMFS: ========================= CHECK FOR FIRMWARE UPDATE =========================
===INITRAMFS: No new firmware to update.
===INITRAMFS: No UserData detected. Creating one ...
===INITRAMFS: uboot without gpt capacities, create user data
[ 7.280000] sda:The number of cy sda1linders for this < disk is set to sda5121601.
There i sda6s nothing wrong sda7with that, but t sda8his is larger th sda9an 1024,
and co sda10uld in certain s >etups cause prob sda2lems with:
1) s
oftware that runs at boot time (e.g., old versions of LILO)
2) booting and partitioning software from other OSs
(e.g., DOS FDISK, OS/2 FDISK)
Command (m for help): Command action
l logical (5 or over)
p primary partition (1-4)
Partition number (1-4): First cylinder (252-121601, default 252): Using default value 252
Last cylinder or +size or +sizeM or +sizeK (252-121601, default 121601): Using default value 121601
Command (m for help): The partition table has been altered!
Calling ioctl() to re-read partition table
===INITRAMFS: Found available BootFS partition: /dev/sda7
===INITRAMFS: First boot. Creating bootfs system array with /dev/sda7
===INITRAMFS: Clean superblock for device /dev/sda7
mdadm: Unrecognised md component device - /dev/sda7
mdadm: /dev/sda7 appears to contain an ext2fs file system
size=16032K mtime=Mon Dec 8 21:50:01 2014
mdad[ 7.490000] md: bind<sda7>
m: size set to 1[ 7.500000] raid1: raid set md0 active with 1 out of 5 mirrors
5936K
Continue [ 7.500000] md0: detected capacity change from 0 to 16318464
creating array? mdadm: array /dev/md0 started.
[ 7.520000] md0: unknown partition table
===INITRAMFS: Mouting /dev/md0 o[ 8.350000] kjournald starting. Commit interval 5 seconds
n /root read onl[ 8.350000] EXT3-fs: mounted filesystem with writeback data mode.
y
===INITRAMFS: Switching to bootfs, leaving initramfs
===BOOTFS: =======================================BOOTFS=================================
===BOOTFS: Initializing filesystem
===BOOTFS: Mounting /proc
mount: /etc/mtab: Read-only file system
===BOOTFS: Mounting /sys
mount: /etc/mtab: Read-only file system
===BOOTFS: Populating /dev
===BOOTFS: Mounting /dev/pts
mount: /etc/mtab: Read-only file system
===BOOTFS: Mounting /dev/shm
mount: /etc/mtab: Read-only file system
===BOOTFS: Verifying MAC address
===BOOTFS: Could not determine MAC address
===BOOTFS: FAILED verifyMacAddress
[ 9.260000] kjournald starting. Commit interval 5 seconds
[ 9.260000] EXT3 FS on sda8, internal journal
[ 9.270000] EXT3-fs: mounted filesystem with writeback data mode.
===BOOTFS: Updating fstab with device /dev/md3.
===BOOTFS: Updating fstab with device /dev/md4.
===BOOTFS: Creating partitions on /dev/sdb
[ 11.720000] sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > sdb2
[ 13.780000] sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 sdb9 sdb10 > sdb2
===BOOTFS: Creating partitions on /dev/sdc
[ 19.920000] sdc: sdc1 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 > sdc2
[ 21.970000] sdc: sdc1 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 > sdc2
===BOOTFS: Creating partitions on /dev/sdd
[ 28.100000] sdd: sdd1 < sdd5 sdd6 sdd7 sdd8 sdd9 sdd10 > sdd2
[ 30.160000] sdd: sdd1 < sdd5 sdd6 sdd7 sdd8 sdd9 sdd10 > sdd2
===BOOTFS: Creating partitions on /dev/sde
[ 36.290000] sde: sde1 < sde5 sde6 sde7 sde8 sde9 sde10 > sde2
[ 38.350000] sde: sde1 < sde5 sde6 sde7 sde8 sde9 sde10 > sde2
===BOOTFS: populating /dev with all devices
===BOOTFS: Clean superblock for partition /dev/sda8
===BOOTFS: Clean superblock for partition /dev/sda9
===BOOTFS: Clean superblock for partition /dev/sda2
===BOOTFS: Clean superblock for partition /dev/sda5
===BOOTFS: Clean superblock for partition /dev/sdb7
===BOOTFS: Clean superblock for partition /dev/sdb8
===BOOTFS: Clean superblock for partition /dev/sdb9
===BOOTFS: Clean superblock for partition /dev/sdb2
===BOOTFS: Clean superblock for partition /dev/sdb5
===BOOTFS: Clean superblock for partition /dev/sdc7
===BOOTFS: Clean superblock for partition /dev/sdc8
===BOOTFS: Clean superblock for partition /dev/sdc9
===BOOTFS: Clean superblock for partition /dev/sdc2
===BOOTFS: Clean superblock for partition /dev/sdc5
===BOOTFS: Clean superblock for partition /dev/sdd7
===BOOTFS: Clean superblock for partition /dev/sdd8
===BOOTFS: Clean superblock for partition /dev/sdd9
===BOOTFS: Clean superblock for partition /dev/sdd2
===BOOTFS: Clean superblock for partition /dev/sdd5
===BOOTFS: Clean superblock for partition /dev/sde7
===BOOTFS: Clean superblock for partition /dev/sde8
===BOOTFS: Clean superblock for partition /dev/sde9
===BOOTFS: Clean superblock for partition /dev/sde2
===BOOTFS: Clean superblock for partition /dev/sde5
===BOOTFS: Warning: addBootfsComponents() /dev/sda7 is already part of /dev/md0, won't add it
===BOOTFS: addBootfsComponents() Adding /dev/sdb7 to /dev/md0
[ 44.460000] md: bind<sdb7>
[ 44.580000] RAID1 conf printout:
[ 44.580000] --- wd:1 rd:5
[ 44.580000] disk 0, wo:0, o:1, dev:sda7
[ 44.580000] disk 1, wo:1, o:1, dev:sdb7
[ 44.590000] md: recovery of RAID array md0
[ 44.590000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 44.600000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 44.610000] md: using 128k window, over a total of 15936 blocks.
===BOOTFS: addBootfsComponents() Adding /dev/sdc7 to /dev/md0
[ 44.700000] md: bind<sdc7>
===BOOTFS: addBootfsComponents() Adding /dev/sdd7 to /dev/md0
[ 45.010000] md: bind<sdd7>
===BOOTFS: addBootfsComponents() Adding /dev/sde7 to /dev/md0
[ 45.230000] md: bind<sde7>
===BOOTFS: Synchronizing /dev/md0
[ 49.020000] md: md0: recovery done.
[ 49.260000] RAID1 conf printout:
[ 49.260000] --- wd:2 rd:5
[ 49.260000] disk 0, wo:0, o:1, dev:sda7
[ 49.260000] disk 1, wo:0, o:1, dev:sdb7
[ 49.370000] RAID1 conf printout:
[ 49.370000] --- wd:2 rd:5
[ 49.370000] disk 0, wo:0, o:1, dev:sda7
[ 49.370000] disk 1, wo:0, o:1, dev:sdb7
[ 49.380000] disk 2, wo:1, o:1, dev:sde7
[ 49.380000] RAID1 conf printout:
[ 49.390000] --- wd:2 rd:5
[ 49.390000] disk 0, wo:0, o:1, dev:sda7
[ 49.390000] disk 1, wo:0, o:1, dev:sdb7
[ 49.400000] disk 2, wo:1, o:1, dev:sde7
[ 49.400000] disk 3, wo:1, o:1, dev:sdd7
[ 49.400000] RAID1 conf printout:
[ 49.410000] --- wd:2 rd:5
[ 49.410000] disk 0, wo:0, o:1, dev:sda7
[ 49.410000] disk 1, wo:0, o:1, dev:sdb7
[ 49.420000] disk 2, wo:1, o:1, dev:sde7
[ 49.420000] disk 3, wo:1, o:1, dev:sdd7
[ 49.430000] disk 4, wo:1, o:1, dev:sdc7
[ 49.430000] md: recovery of RAID array md0
[ 49.430000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 49.440000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for recovery.
[ 49.450000] md: using 128k window, over a total of 15936 blocks.
[ 52.290000] md: md0: recovery done.
[ 52.590000] RAID1 conf printout:
[ 52.590000] --- wd:5 rd:5
[ 52.590000] disk 0, wo:0, o:1, dev:sda7
[ 52.590000] disk 1, wo:0, o:1, dev:sdb7
[ 52.600000] disk 2, wo:0, o:1, dev:sde7
[ 52.600000] disk 3, wo:0, o:1, dev:sdd7
[ 52.610000] disk 4, wo:0, o:1, dev:sdc7
===BOOTFS: updateMiscPartitionsFrom /dev/sda
===BOOTFS: disk is /dev/sda
===BOOTFS: disk is /dev/sdb
===BOOTFS: updateMiscPartitionsFrom: Updating kernel partition(6) on /dev/sdb6
===BOOTFS: updateMiscPartitionsFrom: Clearing secondary kernel partition(10) on /dev/sdb10
===BOOTFS: disk is /dev/sdc
===BOOTFS: updateMiscPartitionsFrom: Updating kernel partition(6) on /dev/sdc6
===BOOTFS: updateMiscPartitionsFrom: Clearing secondary kernel partition(10) on /dev/sdc10
===BOOTFS: disk is /dev/sdd
===BOOTFS: updateMiscPartitionsFrom: Updating kernel partition(6) on /dev/sdd6
===BOOTFS: updateMiscPartitionsFrom: Clearing secondary kernel partition(10) on /dev/sdd10
===BOOTFS: disk is /dev/sde
===BOOTFS: updateMiscPartitionsFrom: Updating kernel partition(6) on /dev/sde6
===BOOTFS: updateMiscPartitionsFrom: Clearing secondary kernel partition(10) on /dev/sde10
===BOOTFS: Creating system RAID array /dev/md1
[ 60.960000] md: bind<sda8>
[ 60.960000] md: bind<sdb8>
[ 60.960000] md: bind<sdc8>
[ 60.970000] md: bind<sdd8>
[ 60.970000] md: bind<sde8>
[ 60.990000] raid1: md1 is not clean -- starting background reconstruction
[ 61.000000] raid1: raid set md1 active with 5 out of 5 mirrors
[ 61.000000] md1: detected capacity change from 0 to 871759872
[ 61.010000] md: resync of RAID array md1
[ 61.010000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 61.020000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 61.030000] md: using 128k window, over a total of 851328 blocks.
[ 61.040000] md1: unknown partition table
===BOOTFS: Synchronizing /dev/md1
[ 75.760000] md: md1: resync done.
[ 75.910000] RAID1 conf printout:
[ 75.910000] --- wd:5 rd:5
[ 75.910000] disk 0, wo:0, o:1, dev:sda8
[ 75.910000] disk 1, wo:0, o:1, dev:sdb8
[ 75.920000] disk 2, wo:0, o:1, dev:sdc8
[ 75.920000] disk 3, wo:0, o:1, dev:sdd8
[ 75.930000] disk 4, wo:0, o:1, dev:sde8
===BOOTFS: Creating system RAID array /dev/md2
[ 76.280000] md: bind<sda9>
[ 76.280000] md: bind<sdb9>
[ 76.280000] md: bind<sdc9>
[ 76.290000] md: bind<sdd9>
[ 76.290000] md: bind<sde9>
[ 76.300000] raid1: md2 is not clean -- starting background reconstruction
[ 76.300000] raid1: raid set md2 active with 5 out of 5 mirrors
[ 76.310000] md2: detected capacity change from 0 to 896401408
[ 76.320000] md: resync of RAID array md2
[ 76.320000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 76.320000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 76.330000] md: using 128k window, over a total of 875392 blocks.
[ 76.350000] md2: unknown partition table
===BOOTFS: Synchronizing /dev/md2
[ 91.250000] md: md2: resync done.
[ 91.400000] RAID1 conf printout:
[ 91.400000] --- wd:5 rd:5
[ 91.400000] disk 0, wo:0, o:1, dev:sda9
[ 91.400000] disk 1, wo:0, o:1, dev:sdb9
[ 91.410000] disk 2, wo:0, o:1, dev:sdc9
[ 91.410000] disk 3, wo:0, o:1, dev:sdd9
[ 91.420000] disk 4, wo:0, o:1, dev:sde9
===BOOTFS: Creating system RAID array /dev/md3
[ 91.800000] md: bind<sda5>
[ 91.800000] md: bind<sdb5>
[ 91.810000] md: bind<sdc5>
[ 91.810000] md: bind<sdd5>
[ 91.810000] md: bind<sde5>
[ 91.820000] raid1: md3 is not clean -- starting background reconstruction
[ 91.830000] raid1: raid set md3 active with 5 out of 5 mirrors
[ 91.830000] md3: detected capacity change from 0 to 263061504
[ 91.840000] md: resync of RAID array md3
[ 91.840000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 91.850000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 91.860000] md: using 128k window, over a total of 256896 blocks.
[ 91.870000] md3: unknown partition table
===BOOTFS: Synchronizing /dev/md3
[ 98.170000] md: md3: resync done.
[ 98.310000] RAID1 conf printout:
[ 98.310000] --- wd:5 rd:5
[ 98.310000] disk 0, wo:0, o:1, dev:sda5
[ 98.310000] disk 1, wo:0, o:1, dev:sdb5
[ 98.320000] disk 2, wo:0, o:1, dev:sdc5
[ 98.320000] disk 3, wo:0, o:1, dev:sdd5
[ 98.330000] disk 4, wo:0, o:1, dev:sde5
===BOOTFS: create_User: RAID level set to raid5
[ 98.970000] md: bind<sda2>
[ 98.980000] md: bind<sdb2>
[ 98.980000] md: bind<sdc2>
[ 98.980000] md: bind<sdd2>
[ 98.990000] md: bind<sde2>
[ 98.990000] raid5: md4 is not clean -- starting background reconstruction
[ 99.000000] raid5: device sde2 operational as raid disk 4
[ 99.000000] raid5: device sdd2 operational as raid disk 3
[ 99.010000] raid5: device sdc2 operational as raid disk 2
[ 99.010000] raid5: device sdb2 operational as raid disk 1
[ 99.020000] raid5: device sda2 operational as raid disk 0
[ 99.030000] raid5: allocated 5258kB for md4
[ 99.030000] raid5: raid level 5 set md4 active with 5 out of 5 devices, algorithm 2
[ 99.040000] RAID5 conf printout:
[ 99.040000] --- rd:5 wd:5
[ 99.040000] disk 0, o:1, dev:sda2
[ 99.050000] disk 1, o:1, dev:sdb2
[ 99.050000] disk 2, o:1, dev:sdc2
[ 99.050000] disk 3, o:1, dev:sdd2
[ 99.060000] disk 4, o:1, dev:sde2
[ 99.060000] md4: detected capacity change from 0 to 3992549588992
[ 99.070000] md: resync of RAID array md4
[ 99.070000] md: minimum _guaranteed_ speed: 1000 KB/sec/disk.
[ 99.080000] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync.
[ 99.090000] md: using 128k window, over a total of 974743552 blocks.
[ 99.100000] md4: unknown partition table
===BOOTFS: Preparing swap partition /dev/md3
===BOOTFS: Preparing snapshot partition /dev/md2
[ 100.650000] kjournald starting. Commit interval 5 seconds
[ 100.650000] EXT3-fs: mounted filesystem with writeback data mode.
[ 101.660000] kjournald starting. Commit interval 5 seconds
[ 101.670000] EXT3 FS on md2, internal journal
[ 101.670000] EXT3-fs: mounted filesystem with writeback data mode.
readlink: /dev/md4: Invalid argument
===BOOTFS: Preparing userdata partition /dev/md4
[ 102.870000] kjournald starting. Commit interval 5 seconds
[ 102.880000] EXT3-fs: mounted filesystem with writeback data mode.
[ 121.560000] XFS mounting filesystem md4
meta-data=/dev/md4 isize=256 agcount=33, agsize=8388480 blks
= sectsz=4096 attr=2
data = bsize=4096 blocks=268435456, imaxpct=5
= sunit=128 swidth=512 blks
naming =version 2 bsize=4096 ascii-ci=0
log =internal bsize=4096 blocks=131072, version=2
= sectsz=4096 sunit=1 blks, lazy-count=0
realtime =none extsz=4096 blocks=0, rtextents=0
data blocks changed from 268435456 to 974743552
===BOOTFS: ####### Writing first_boot signature on /dev/sda #######
===BOOTFS: ####### signing all devices with net5big_v2 #######
===BOOTFS: #### Running File System Check on Snapshot Partition (/dev/md2) ###
e2fsck 1.37 (21-Mar-2005)
/dev/md2: clean, 687/109536 files, 8333/218848 blocks
#### Starting PatchManager using /dev/md1 and /dev/md2 ####
[ 146.650000] kjournald starting. Commit interval 5 seconds
[ 146.650000] EXT3-fs: mounted filesystem with writeback data mode.
[ 146.700000] kjournald starting. Commit interval 5 seconds
[ 146.710000] EXT3 FS on md2, internal journal
[ 146.710000] EXT3-fs: mounted filesystem with writeback data mode.
===BOOTFS: Creating base union /var/base from /var/original
===BOOTFS: Loading snapshots from /snapshots/snaps
[ 146.900000] unionfs: unionfs: new generation number 2
mount: /etc/mtab: Read-only file system
[ 147.000000] unionfs: unionfs: new generation number 3
mount: /etc/mtab: Read-only file system
[34;01m Next Generation Init version ( 0.6.10.2 Die bugs die! )[0m
[32;01m http://www.initng.org
[0m Author: Jimmy Wennlund <jimmy.wennlund@gmail.com>
If you find initng useful, please consider a small donation.
System is starting up!
[01;31m [0m[34;01mrunlevel/default[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01minitial[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mdbus[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mdbus/uuidgen[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mudev/filldev[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mudev/udevd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mudev/mountdev[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mudev/set_hotplug[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mhald[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mdhcdbd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mbonding[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mklogd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msyslogd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mlogrotate[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mraid[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01musb[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mNetworkManager[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mNetworkManager/prepare[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mhttp[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mgetty/1[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msshd/generate_keys[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mcron[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01municorn[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mlvm[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mthumbd[0m[36G [[32;01mstarting[0m]
[36;01m initial start:[0m
Copying /oldroot/var/original/bin to /oldroot/snapshots/snaps/00/bin
Copying /oldroot/var/original/sbin to /oldroot/snapshots/snaps/00/sbin
Copying /oldroot/var/original/lib to /oldroot/snapshots/snaps/00/lib
Copying /oldroot/var/original/usr to /oldroot/snapshots/snaps/00/usr
Copying /oldroot/var/original/www to /oldroot/snapshots/snaps/00/www
load RTC date: Sat Dec 13 08:55:08 UTC 2014
save file date: Sat Dec 13 08:55:08 UTC 2014
[01;31m 3% [0m[34;01minitial[0m[36G [[32;01mdone[0m] ( done in 38138ms )
[01;31m 7% [0m[34;01mNetworkManager/prepare[0m[36G [[32;01mdone[0m] ( done in 46ms )
[01;31m 10% [0m[34;01mudev/mountdev[0m[36G [[32;01mdone[0m] ( done in 95ms )
[01;31m 14% [0m[34;01mcron[0m[36G [[32;01mstarted[0m] ( pid: 2597 )
[01;31m 17% [0m[34;01mdbus/uuidgen[0m[36G [[32;01mdone[0m] ( done in 267ms )
[01;31m 25% [0m[34;01mthumbd[0m[36G [[32;01mstarted[0m] ( pid: 2598 )
[01;31m 25% [0m[34;01mlogrotate[0m[36G [[32;01mdone[0m] ( done in 302ms )
[01;31m 32% [0m[34;01mudev/udevd[0m[36G [[32;01mstarted[0m] ( pid: 2596 )
[01;31m 32% [0m[34;01msyslogd[0m[36G [[32;01mstarted[0m] ( pid: 2604 )
[01;31m 39% [0m[34;01mklogd[0m[36G [[32;01mstarted[0m] ( pid: 2608 )
[01;31m 42% [0m[34;01mdbus[0m[36G [[32;01mstarted[0m] ( pid: 2612 )
[01;31m 46% [0m[34;01mudev/set_hotplug[0m[36G [[32;01mdone[0m] ( done in 198ms )
[01;31m [0m[34;01mudev/udevd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mudev/udevd[0m[36G [[32;01mstarting[0m]
[01;31m 46% [0m[34;01mudev/udevd[0m[36G [[32;01mstarted[0m] ( pid: 2622 )
[01;31m 53% [0m[34;01mudev/filldev[0m[36G [[32;01mdone[0m] ( done in 14341ms )
[01;31m 53% [0m[34;01mbonding[0m[36G [[32;01mdone[0m] ( done in 14189ms )
[01;31m 64% [0m[34;01mhald[0m[36G [[32;01mstarted[0m] ( pid: 3662 )
[01;31m 64% [0m[34;01mgetty/1[0m[36G [[32;01mstarted[0m] ( pid: 3667 )
[01;31m 67% [0m[34;01mdhcdbd[0m[36G [[32;01mstarted[0m] ( pid: 3672 )
[01;31m 71% [0m[34;01musb[0m[36G [[32;01mdone[0m] ( done in 85ms )
[01;31m 75% [0m[34;01mNetworkManager[0m[36G [[32;01mstarted[0m] ( pid: 3683 )
[01;31m 82% [0m[34;01mhttp[0m[36G [[32;01mstarted[0m] ( pid: 3686 )
LaCix Linux release 2.2.10.1
Kernel 2.6.31.14-svn6790 on an armv5tel / ttyS0
(none) login: [01;31m 86% [0m[34;01mraid[0m[36G [[32;01mdone[0m] ( done in 5295ms )
[01;31m 89% [0m[34;01mlvm[0m[36G [[32;01mdone[0m] ( done in 645ms )
[01;31m 93% [0m[34;01municorn[0m[36G [[32;01mstarted[0m] ( pid: 3750 )
[01;31m [0m[34;01mfan_controller[0m[36G [[32;01mstarting[0m]
[01;31m 93% [0m[34;01mfan_controller[0m[36G [[32;01mstarted[0m] ( pid: 3873 )
[01;31m 96% [0m[34;01msshd/generate_keys[0m[36G [[32;01mdone[0m] ( done in 37053ms )
[01;31m 100% [0m[34;01mrunlevel/default[0m[36G [[32;01mdone[0m] ( done in 89874ms )
runlevel "runlevel/default" up in, 89977ms.
[01;31m [0m[34;01mmdadm[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mmdadm[0m[36G [[32;01mdone[0m] ( done in 41ms )
[01;31m [0m[34;01miscsitarget[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01miscsitarget/system[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01miscsitarget/system[0m[36G [[32;01mdone[0m] ( done in 78ms )
[01;31m [0m[34;01miscsitarget[0m[36G [[32;01mstarted[0m] ( pid: 4103 )
[36;01m iscsitarget daemon:[0m
1418461019.213156: unable to create server socket (Address family not supported by protocol) 10 1 6!
[01;31m [0m[34;01mavahi[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mavahi[0m[36G [[32;01mstarted[0m] ( pid: 4111 )
[01;31m [0m[34;01mipcommd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mipcommd[0m[36G [[32;01mstarted[0m] ( pid: 4126 )
[01;31m [0m[34;01mnetatalk/cnid_metad[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mnetatalk/cnid_metad[0m[36G [[32;01mstarted[0m] ( pid: 4169 )
[01;31m [0m[34;01mnetatalk/afpd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mnetatalk/afpd[0m[36G [[32;01mstarted[0m] ( pid: 4174 )
[01;31m [0m[34;01msamba/smbd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msamba/initial[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msamba/initial[0m[36G [[32;01mdone[0m] ( done in 217ms )
[01;31m [0m[34;01msamba/smbd[0m[36G [[32;01mstarted[0m] ( pid: 4221 )
[01;31m [0m[34;01msamba/nmbd[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msamba/nmbd[0m[36G [[32;01mstarted[0m] ( pid: 4224 )
[01;31m [0m[34;01msamba/winbind[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01msamba/winbind[0m[36G [[32;01mstarted[0m] ( pid: 4227 )
[01;31m [0m[34;01mcups[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mcups[0m[36G [[32;01mstarted[0m] ( pid: 4236 )
[01;31m [0m[34;01mreload/netatalk[0m[36G [[32;01mstarting[0m]
[01;31m [0m[34;01mreload/netatalk[0m[36G [[32;01mdone[0m] ( done in 51ms )