Unable to instal v18 on my Edmin V2

[arssant]

Hi
Following my 1s post yesterday: https://plugout.net/viewtopic.php?f=9&t=3581
I made a new try, and started a fresh install via console utility v18 firmware.
Every 1st steeps worked fine, detection, firmware selection, tftp sending firmware. but as you can see on the log ( serial console ) got kernel panic, and lacie stop responding.
Any clue ? I followed the tuto and faq, and fresh HD ( used one, no partitions, but no delays, no crc´s... )

Code: Select all

         __  __                      _ _
        |  \/  | __ _ _ ____   _____| | |
        | |\/| |/ _` | '__\ \ / / _ \ | |
        | |  | | (_| | |   \ V /  __/ | |
        |_|  |_|\__,_|_|    \_/ \___|_|_|
 _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
 \___/    |____/ \___/ \___/ \__|  ** LOADER **
 ** MARVELL BOARD: DB-88F5182-EDmini-V2 LE

U-Boot 1.1.1 (Sep  3 2008 - 07:36:51) Marvell version: 1.7.3 - LaCie version: 1.                                        3.4

DRAM CS[0] base 0x00000000   size  64MB
DRAM Total size  64MB
Flash: flashStructGet manu 0xff id 0xff
[0kB@fff80000] ## Unknown FLASH at fff80000: Size = 0x00000000 = 0 MB
Flash:  0 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment


Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Waiting for LUMP (2)
Using egiga0 device
Lump received switching to NetConsole on 192.168.3.157
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1                                         (GCC) ) #1 Sat May 16 23:32:53 CEST 2015
[    0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
[    0.000000] CPU: VIVT data cache, VIVT instruction cache
[    0.000000] Machine: LaCie Ethernet Disk mini V2
[    0.000000] Clearing invalid memory bank 0KB@0xffffffff
[    0.000000] Clearing invalid memory bank 0KB@0xffffffff
[    0.000000] Clearing invalid memory bank 0KB@0xffffffff
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Ignoring unrecognised tag 0x00000000
[    0.000000] Ignoring unrecognised tag 0x41000403
[    0.000000] Memory policy: Data cache writeback
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pag                                        es: 16256
[    0.000000] Kernel command line: console=ttyS0,115200 netconsole=6666@192.168                                        .3.252/,6666@192.168.3.157/
[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Memory: 57116K/65536K available (5565K kernel code, 276K rwdata,                                         1544K rodata, 150K init, 244K bss, 8420K reserved)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xc4800000 - 0xff000000   ( 936 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xc4000000   (  64 MB)
[    0.000000]     modules : 0xbf000000 - 0xc0000000   (  16 MB)
[    0.000000]       .text : 0xc0008000 - 0xc06f997c   (7111 kB)
[    0.000000]       .init : 0xc06fa000 - 0xc071fbf0   ( 151 kB)
[    0.000000]       .data : 0xc0720000 - 0xc0765200   ( 277 kB)
[    0.000000]        .bss : 0xc0765200 - 0xc07a2234   ( 245 kB)
[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[    0.000000] NR_IRQS:64
[    0.000020] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769                                        803770ns
[    7.850381] Console: colour dummy device 80x30
[    7.850431] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[    7.920117] pid_max: default: 32768 minimum: 301
[    7.920446] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    7.920488] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[    7.921741] CPU: Testing write buffer coherency: ok
[    7.922406] Setting up static identity map for 0x547f40 - 0x547f7c
[    7.926849] VFP support v0.3: not present
[    7.928194] NET: Registered protocol family 16
[    7.929319] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    7.933684] Orion ID: MV88F5182-A2. TCLK=166666667.
[    7.939828] edmini_v2: USB device port, flash write and power-off are not yet                                         supported.
[    8.016226] bio: create slab <bio-0> at 0
[    8.018135] vgaarb: loaded
[    8.019803] SCSI subsystem initialized
[    8.023534] usbcore: registered new interface driver usbfs
[    8.024031] usbcore: registered new interface driver hub
[    8.024595] usbcore: registered new device driver usb
[    8.025768] Linux video capture interface: v2.00
[    8.030538] cfg80211: Calling CRDA to update world regulatory domain
[    8.031253] Switched to clocksource orion_clocksource
[    8.077286] NET: Registered protocol family 2
[    8.078441] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[    8.078522] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[    8.078583] TCP: Hash tables configured (established 1024 bind 1024)
[    8.078728] TCP: reno registered
[    8.078774] UDP hash table entries: 256 (order: 0, 4096 bytes)
[    8.078842] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[    8.079277] NET: Registered protocol family 1
[    8.079852] RPC: Registered named UNIX socket transport module.
[    8.079882] RPC: Registered udp transport module.
[    8.079906] RPC: Registered tcp transport module.
[    8.079930] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    8.080329] NetWinder Floating Point Emulator V0.97 (double precision)
[    8.083958] futex hash table entries: 256 (order: -1, 3072 bytes)
[    8.124350] VFS: Disk quotas dquot_6.5.2
[    8.125330] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    8.140045] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[    8.143250] NTFS driver 2.1.30 [Flags: R/W].
[    8.144982] fuse init (API version 7.22)
[    8.148893] SGI XFS with ACLs, security attributes, realtime, large block/ino                                        de numbers, no debug enabled
[    8.159326] msgmni has been set to 111
[    8.162919] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 2                                        53)
[    8.162954] io scheduler noop registered
[    8.162980] io scheduler deadline registered
[    8.163087] io scheduler cfq registered (default)
[    8.182419] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    8.205340] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3, base_baud = 1041                                        6666) is a 16550A
[    8.657706] console [ttyS0] enabled
[    8.690368] brd: module loaded
[    8.707797] loop: module loaded
[    8.711798] Uniform Multi-Platform E-IDE driver
[    8.717149] ide-gd driver 1.18
[    8.724983] sata_mv sata_mv.0: cannot get optional clkdev
[    8.731353] sata_mv sata_mv.0: slots 32 ports 2
[    8.746672] scsi0 : sata_mv
[    8.751341] scsi1 : sata_mv
[    8.755562] ata1: SATA max UDMA/133 irq 29
[    8.759670] ata2: SATA max UDMA/133 irq 29
[    8.767255] physmap platform flash device: 00080000 at fff80000
[    8.773425] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufa                                        cturer ID 0x0000c2 Chip ID 0x0000b9
[    8.784125] Support for command set 0002 not present
[    8.789090] gen_probe: No supported Vendor Command Set found
[    8.795787] physmap-flash physmap-flash.0: map_probe failed
[    8.803502] tun: Universal TUN/TAP device driver, 1.6
[    8.808549] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[    8.815361] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn                                        .edu>
[    8.824834] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393                                        @maroon.tc.umn.edu>
[    8.842019] libphy: orion_mdio_bus: probed
[    8.846608] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[    8.933136] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address                                         00:d0:4b:87:df:15
[    8.942280] PPP generic driver version 2.4.2
[    8.947513] PPP Deflate Compression module registered
[    8.952612] PPP MPPE Compression module registered
[    8.957398] NET: Registered protocol family 24
[    8.962394] usbcore: registered new interface driver rtl8187
[    8.968618] usbcore: registered new interface driver rtl8192cu
[    8.974996] usbcore: registered new interface driver rt2500usb
[    8.981361] usbcore: registered new interface driver rt73usb
[    8.987523] usbcore: registered new interface driver rt2800usb
[    8.993399] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet dri                                        ver
[    9.001285] usbcore: registered new interface driver pegasus
[    9.007440] usbcore: registered new interface driver asix
[    9.013342] usbcore: registered new interface driver ax88179_178a
[    9.019913] usbcore: registered new interface driver cdc_ether
[    9.026272] usbcore: registered new interface driver net1080
[    9.032440] usbcore: registered new interface driver cdc_subset
[    9.038867] usbcore: registered new interface driver ipheth
[    9.045021] usbcore: registered new interface driver cdc_ncm
[    9.053967] aoe: cannot create debugfs directory
[    9.058901] aoe: AoE v85 initialised.
[    9.062661] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    9.069173] ehci-pci: EHCI PCI platform driver
[    9.074176] ehci-orion: EHCI orion driver
[    9.078327] orion-ehci orion-ehci.0: EHCI Host Controller
[    9.083818] orion-ehci orion-ehci.0: new USB bus registered, assigned bus num                                        ber 1
[    9.091738] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
[    9.110133] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[    9.116174] ata1: SATA link down (SStatus 0 SControl 300)
[    9.124411] hub 1-0:1.0: USB hub found
[    9.128247] hub 1-0:1.0: 1 port detected
[    9.134113] usbcore: registered new interface driver usblp
[    9.140255] usbcore: registered new interface driver usb-storage
[    9.146890] mousedev: PS/2 mouse device common for all mice
[    9.153693] i2c /dev entries driver
[    9.162649] rtc-rs5c372 0-0032: clock needs to be set
[    9.167716] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[    9.176785] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[    9.192673] uvcvideo: Unable to create debugfs directory
[    9.198517] usbcore: registered new interface driver uvcvideo
[    9.204296] USB Video Class driver (1.1.1)
[    9.208386] gspca_main: v2.14.0 registered
[    9.213034] usbcore: registered new interface driver Philips webcam
[    9.219292] Driver for 1-wire Dallas network protocol.
[    9.232150] Netfilter messages via NETLINK v0.30.
[    9.236978] nf_conntrack version 0.5.0 (892 buckets, 3568 max)
[    9.244532] ipip: IPv4 over IPv4 tunneling driver
[    9.251896] ip_tables: (C) 2000-2006 Netfilter Core Team
[    9.257500] TCP: cubic registered
[    9.265046] NET: Registered protocol family 10
[    9.271758] ip6_tables: (C) 2000-2006 Netfilter Core Team
[    9.277501] sit: IPv6 over IPv4 tunneling driver
[    9.284575] NET: Registered protocol family 17
[    9.289060] NET: Registered protocol family 5
[    9.293711] NET: Registered protocol family 37
[    9.300433] netpoll: netconsole: local port 6666
[    9.305060] netpoll: netconsole: local IPv4 address 192.168.3.252
[    9.311177] netpoll: netconsole: interface 'eth0'
[    9.315881] netpoll: netconsole: remote port 6666
[    9.320610] netpoll: netconsole: remote IPv4 address 192.168.3.157
[    9.326780] netpoll: netconsole: remote ethernet address ff:ff:ff:ff:ff:ff
[    9.333666] netpoll: netconsole: device eth0 not up yet, forcing it
[    9.420990] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[   10.890138] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[   10.930209] ata2.00: ATA-8: TOSHIBA MK3265GSX, GJ002H, max UDMA/100
[   10.936497] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[   10.960511] ata2.00: configured for UDMA/100
[   10.965423] scsi 1:0:0:0: Direct-Access     ATA      TOSHIBA MK3265GS GJ00 PQ                                        : 0 ANSI: 5
[   10.975094] fvdw1 disk index before get_sd_name = 0
[   10.979967] No LaCie disk map available
[   10.983842] fvdw2 disk index after get_sd_name = 0
[   10.988624] fvdw3 prefix[0]=s  prefix[1]=d
[   10.992735] fvdw4 diskname = sda
[   10.997426] sd 1:0:0:0: [sda] 625142448 512-byte logical blocks: (320 GB/298                                         GiB)
[   11.006710] sd 1:0:0:0: [sda] Write Protect is off
[   11.011966] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, does                                        n't support DPO or FUA
[   11.046143]  sda:
[   11.050992] sd 1:0:0:0: [sda] Attached SCSI disk
[   11.098890] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 100 Mb/s, full                                         duplex, flow control disabled
[   11.108685] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   11.122903] console [netcon0] enabled
[   11.126574] netconsole: network logging started
[   11.132896] rtc-rs5c372 0-0032: hctosys: unable to read the hardware clock
[   11.140668] VFS: Cannot open root device "(null)" or unknown-block(0,0): erro                                        r -6
[   11.148199] Please append a correct "root=" boot option; here are the availab                                        le partitions:
[   11.156639] 0800       312571224 sda  driver: sd
[   11.161701] Kernel panic - not syncing: VFS: Unable to mount root fs on unkno                                        wn-block(0,0)
[   11.169972] CPU: 0 PID: 1 Comm: swapper Not tainted 3.14.2 #1
[   11.175772] [<c0018924>] (unwind_backtrace) from [<c0015610>] (show_stack+0x1                                        0/0x14)
[   11.183542] [<c0015610>] (show_stack) from [<c0540784>] (panic+0x78/0x1c4)
[   11.190468] [<c0540784>] (panic) from [<c06faf38>] (mount_block_root+0x210/0x                                        258)
[   11.197989] [<c06faf38>] (mount_block_root) from [<c06fb154>] (mount_root+0xd                                        c/0x104)
[   11.205859] [<c06fb154>] (mount_root) from [<c06fb2c8>] (prepare_namespace+0x                                        14c/0x1a0)
[   11.213905] [<c06fb2c8>] (prepare_namespace) from [<c06fab54>] (kernel_init_f                                        reeable+0x174/0x1b8)
[   11.222812] [<c06fab54>] (kernel_init_freeable) from [<c053f3c4>] (kernel_ini                                        t+0x8/0xe4)
[   11.230941] [<c053f3c4>] (kernel_init) from [<c0012550>] (ret_from_fork+0x14/                                        0x24)



Thanks in advance.

[fvdw]

Which kernel did you choose in fvdw-sl console?

I think you did not select the isp1 standalone kernel.

Or do you get this output after installing firmware and rebooting?
The kernel is trying to load a non existing root file system. This could be because partitioning failed when installing firmware or a because of a defective disk.

But please describe more in detail what you have done

[fvdw]

Looking more close to your output it is clear to me that you did not boot from disk but loaded an external kernel

Code: Select all

Net:   egiga0 [PRIME]
Hit any key to stop autoboot:  0
Waiting for LUMP (2)
Using egiga0 device
Lump received switching to NetConsole on 192.168.3.157
Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0x0

You should see this when normal booting from disk after firmware is installed

Code: Select all

U-Boot 1.1.1 (Jun 15 2007 - 08:56:23) Marvell version: 1.7.3



| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F5182-EDmini-V2 LE


U-Boot 1.1.1 (Sep 3 2008 - 07:36:51) Marvell version: 1.7.3 - LaCie version: 1


DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
Flash: flashStructGet manu 0xff id 0xff
[0kB@fff80000] ## Unknown FLASH at fff80000: Size = 0x00000000 = 0 MB
Flash: 0 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment


Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz


USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Waiting for LUMP (2)
Using egiga0 device
no lump receive; continuing

Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
StartChannel
Device 1: OK
Model: Hitachi HDP725050GLA360 Firm: GM4OA5CA Ser#: GEC5J
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)

** Bad partition - 1:9 1:9 **

Loading from IDE device 1, partition 6: Name: hdb6
Type: U-Boot
Image Name: Linux-2.6.12.6-arm1-lacie5b
Created: 2007-04-20 15:44:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1662140 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-2.6.12.6-arm1-lacie5b
Created: 2007-04-20 15:44:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1662140 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK

Starting kernel ...


[fvdw]

To install firmware you should use kernel UIMAGE-3136-ISP1-14-standalone
Your output mentioned 3.14.2,

Code: Select all

...
[    0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1
...

I think you loaded the kernel from tftp/firmware/isp1 folder.
You should not do that but instead load the standalone kernel and use fvdw-sl-programs command and install firmware

[arssant]

Which kernel did you choose in fvdw-sl console?

I think you did not select the isp1 standalone kernel.

Or do you get this output after installing firmware and rebooting?
The kernel is trying to load a non existing root file system. This could be because partitioning failed when installing firmware or a because of a defective disk.

But please describe more in detail what you have done

Hi.
Stand-alone kernel: ok
Version isp1 : ok
TFTP transfer : successfully
Just after tftp 100% transfer:

Code: Select all

Lump received switching to NetConsole on 192.168.3.151
Uncompressing Linux... done, booting the kernel.
...
...


and the kernel panic at the end, no more serial and telnet from FVDW console disconnecting time out.

Hard drive, checked no bad sector, no crc, no delay. And I tryed 2 HDD, one WD, one toshiba.

Thanks.

[fvdw]

That is not the standalone kernel use the one in tftp folder (not the one in tftp/firmware/isp1

UIMAGE-3136-ISP1-14-standalone

Be sure you use option "install firmware" in fvdw-sl-console and follow the instructions given in the main window

[arssant]

That is not the standalone kernel use the one in tftp folder (not the one in tftp/firmware/isp1

UIMAGE-3136-ISP1-14-standalone

Be sure you use option "install firmware" in fvdw-sl-console and follow the instructions given in the main window

Hi.
My bad opssssy.
I use a lot tftp2 and tftpd by PH Jouning. And my method is create a folder for all dif device by mane, so next time I should read more the faqs.

So with your time and orientation, the result is:

Code: Select all

System Name   fvdwsl-base
IP Address   192.168.3.236
Subnet Mask   255.255.255.0
MAC Address   00:D0:4B:87:DF:15
Workgroup:   mshome
DDNS :   Disabled
Firmware Version   fvdw-sl 18.1 (isp1)
Kernel:   Linux 3.14.2 #1 Sat May 16 23:32:53 CEST 2015
Date   February 11, 2022 04:15:20 PM
Uptime:   0 Days, 00 Hours, 02 Minutes, 18 Seconds


Again, thanks a lot, and to Jocko too.