Things are geting weirder. I can boot up normally only when I am connected to serial port. Here is the output from console:
- Code: Select all
▒▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F5182-EDmini-V2 LE
U-Boot 1.1.1 (Sep 3 2008 - 07:36:51) Marvell version: 1.7.3 - LaCie version: 1. 3.4
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
Flash: flashStructGet manu 0xff id 0xff
[0kB@fff80000] ## Unknown FLASH at fff80000: Size = 0x00000000 = 0 MB
Flash: 0 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Marvell>> ;0 0▒
__ __ _ _
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F5182-EDmini-V2 LE
U-Boot 1.1.1 (Sep 3 2008 - 07:36:51) Marvell version: 1.7.3 - LaCie version: 1.3.4
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
Flash: flashStructGet manu 0xff id 0xff
[0kB@fff80000] ## Unknown FLASH at fff80000: Size = 0x00000000 = 0 MB
Flash: 0 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Waiting for LUMP (2)
Using egiga0 device
no lump receive; continuing
Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
StartChannel
Device 1: OK
Model: TOSHIBA HDWD120 Firm: MX4OACF0 Ser#: 78DJVT0CS
Type: Hard Disk
Supports 48-bit addressing
Capacity: 1907729.0 MB = 1863.0 GB (-387938128 x 512)
** Bad partition - 1:9 1:9 **
Loading from IDE device 1, partition 6: Name: hdb6
Type: U-Boot
Image Name: Linux-3.14.2
Created: 2015-05-16 21:33:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3873552 Bytes = 3.7 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-3.14.2
Created: 2015-05-16 21:33:54 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 3873552 Bytes = 3.7 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux... done, booting the kernel.
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 3.14.2 (root@fvdwsl-5big2.local) (gcc version 4.8.1 (GCC) ) #1 Sat May 16 23:32:53 CEST 2015
[ 0.000000] CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] Machine: LaCie Ethernet Disk mini V2
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Clearing invalid memory bank 0KB@0xffffffff
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] Ignoring unrecognised tag 0x41000403
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 57116K/65536K available (5565K kernel code, 276K rwdata, 1544K rodata, 150K init, 244K bss, 8420K reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff000000 ( 936 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc06f997c (7111 kB)
[ 0.000000] .init : 0xc06fa000 - 0xc071fbf0 ( 151 kB)
[ 0.000000] .data : 0xc0720000 - 0xc0765200 ( 277 kB)
[ 0.000000] .bss : 0xc0765200 - 0xc07a2234 ( 245 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:64
[ 0.000020] sched_clock: 32 bits at 166MHz, resolution 6ns, wraps every 25769803770ns
[ 7.641914] Console: colour dummy device 80x30
[ 7.641964] Calibrating delay loop... 265.42 BogoMIPS (lpj=1327104)
[ 7.711650] pid_max: default: 32768 minimum: 301
[ 7.711980] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.712023] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.713171] CPU: Testing write buffer coherency: ok
[ 7.713838] Setting up static identity map for 0x547f40 - 0x547f7c
[ 7.718440] VFP support v0.3: not present
[ 7.719800] NET: Registered protocol family 16
[ 7.720965] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 7.725411] Orion ID: MV88F5182-A2. TCLK=166666667.
[ 7.731595] edmini_v2: USB device port, flash write and power-off are not yet supported.
[ 7.809290] bio: create slab <bio-0> at 0
[ 7.811195] vgaarb: loaded
[ 7.812921] SCSI subsystem initialized
[ 7.816665] usbcore: registered new interface driver usbfs
[ 7.817168] usbcore: registered new interface driver hub
[ 7.817719] usbcore: registered new device driver usb
[ 7.818867] Linux video capture interface: v2.00
[ 7.823601] cfg80211: Calling CRDA to update world regulatory domain
[ 7.824347] Switched to clocksource orion_clocksource
[ 7.870332] NET: Registered protocol family 2
[ 7.871482] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.871561] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 7.871668] TCP: Hash tables configured (established 1024 bind 1024)
[ 7.871815] TCP: reno registered
[ 7.871861] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 7.871928] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 7.872362] NET: Registered protocol family 1
[ 7.872935] RPC: Registered named UNIX socket transport module.
[ 7.872966] RPC: Registered udp transport module.
[ 7.872989] RPC: Registered tcp transport module.
[ 7.873013] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 7.873394] NetWinder Floating Point Emulator V0.97 (double precision)
[ 7.877076] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 7.918894] VFS: Disk quotas dquot_6.5.2
[ 7.919896] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 7.934980] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 7.938201] NTFS driver 2.1.30 [Flags: R/W].
[ 7.939989] fuse init (API version 7.22)
[ 7.944066] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 7.954692] msgmni has been set to 111
[ 7.958113] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 7.958147] io scheduler noop registered
[ 7.958172] io scheduler deadline registered
[ 7.958279] io scheduler cfq registered (default)
[ 7.977939] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 8.000902] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3, base_baud = 10416666) is a 16550A
[ 8.450455] console [ttyS0] enabled
[ 8.483897] brd: module loaded
[ 8.501765] loop: module loaded
[ 8.505730] Uniform Multi-Platform E-IDE driver
[ 8.511094] ide-gd driver 1.18
[ 8.519026] sata_mv sata_mv.0: cannot get optional clkdev
[ 8.525404] sata_mv sata_mv.0: slots 32 ports 2
[ 8.540745] scsi0 : sata_mv
[ 8.545398] scsi1 : sata_mv
[ 8.549615] ata1: SATA max UDMA/133 irq 29
[ 8.553763] ata2: SATA max UDMA/133 irq 29
[ 8.561352] physmap platform flash device: 00080000 at fff80000
[ 8.567538] physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0000b9
[ 8.578245] Support for command set 0002 not present
[ 8.583240] gen_probe: No supported Vendor Command Set found
[ 8.589906] physmap-flash physmap-flash.0: map_probe failed
[ 8.597651] tun: Universal TUN/TAP device driver, 1.6
[ 8.602737] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 8.609512] ipddp.c:v0.01 8/28/97 Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 8.619035] ipddp0: Appletalk-IP Encap. mode by Bradford W. Johnson <johns393@maroon.tc.umn.edu>
[ 8.636228] libphy: orion_mdio_bus: probed
[ 8.640823] mv643xx_eth: MV-643xx 10/100/1000 ethernet driver version 1.4
[ 8.724702] mv643xx_eth_port mv643xx_eth_port.0 eth0: port 0 with MAC address 00:d0:4b:86:df:f3
[ 8.733847] PPP generic driver version 2.4.2
[ 8.739066] PPP Deflate Compression module registered
[ 8.744164] PPP MPPE Compression module registered
[ 8.748949] NET: Registered protocol family 24
[ 8.753961] usbcore: registered new interface driver rtl8187
[ 8.760200] usbcore: registered new interface driver rtl8192cu
[ 8.766592] usbcore: registered new interface driver rt2500usb
[ 8.772966] usbcore: registered new interface driver rt73usb
[ 8.779134] usbcore: registered new interface driver rt2800usb
[ 8.785011] pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
[ 8.792903] usbcore: registered new interface driver pegasus
[ 8.799071] usbcore: registered new interface driver asix
[ 8.804988] usbcore: registered new interface driver ax88179_178a
[ 8.811560] usbcore: registered new interface driver cdc_ether
[ 8.817926] usbcore: registered new interface driver net1080
[ 8.824100] usbcore: registered new interface driver cdc_subset
[ 8.830536] usbcore: registered new interface driver ipheth
[ 8.836701] usbcore: registered new interface driver cdc_ncm
[ 8.845721] aoe: cannot create debugfs directory
[ 8.850634] aoe: AoE v85 initialised.
[ 8.854393] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 8.860907] ehci-pci: EHCI PCI platform driver
[ 8.865916] ehci-orion: EHCI orion driver
[ 8.870071] orion-ehci orion-ehci.0: EHCI Host Controller
[ 8.875568] orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
[ 8.883485] orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
[ 8.901660] orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
[ 8.907699] ata1: SATA link down (SStatus 0 SControl 300)
[ 8.915961] hub 1-0:1.0: USB hub found
[ 8.919788] hub 1-0:1.0: 1 port detected
[ 8.925694] usbcore: registered new interface driver usblp
[ 8.931853] usbcore: registered new interface driver usb-storage
[ 8.938500] mousedev: PS/2 mouse device common for all mice
[ 8.945329] i2c /dev entries driver
[ 8.954899] rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
[ 8.967111] rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
[ 8.983033] uvcvideo: Unable to create debugfs directory
[ 8.988885] usbcore: registered new interface driver uvcvideo
[ 8.994663] USB Video Class driver (1.1.1)
[ 8.998756] gspca_main: v2.14.0 registered
[ 9.003409] usbcore: registered new interface driver Philips webcam
[ 9.009669] Driver for 1-wire Dallas network protocol.
[ 9.022692] Netfilter messages via NETLINK v0.30.
[ 9.027520] nf_conntrack version 0.5.0 (892 buckets, 3568 max)
[ 9.035101] ipip: IPv4 over IPv4 tunneling driver
[ 9.042481] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.048081] TCP: cubic registered
[ 9.055809] NET: Registered protocol family 10
[ 9.062515] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 9.068263] sit: IPv6 over IPv4 tunneling driver
[ 9.075385] NET: Registered protocol family 17
[ 9.079870] NET: Registered protocol family 5
[ 9.084518] NET: Registered protocol family 37
[ 9.091256] console [netcon0] enabled
[ 9.094963] netconsole: network logging started
[ 9.101127] rtc-rs5c372 0-0032: setting system clock to 2021-10-20 13:06:22 UTC (1634735182)
[ 9.961670] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 10.001716] ata2.00: ATA-8: TOSHIBA HDWD120, MX4OACF0, max UDMA/133
[ 10.007984] ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 10.071733] ata2.00: configured for UDMA/133
[ 10.076684] scsi 1:0:0:0: Direct-Access ATA TOSHIBA HDWD120 MX4O PQ: 0 ANSI: 5
[ 10.086329] fvdw1 disk index before get_sd_name = 0
[ 10.091207] No LaCie disk map available
[ 10.095082] fvdw2 disk index after get_sd_name = 0
[ 10.099864] fvdw3 prefix[0]=s prefix[1]=d
[ 10.103973] fvdw4 diskname = sda
[ 10.108668] sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 10.116453] sd 1:0:0:0: [sda] 4096-byte physical blocks
[ 10.123488] sd 1:0:0:0: [sda] Write Protect is off
[ 10.128693] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 10.190420] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
[ 10.204715] sd 1:0:0:0: [sda] Attached SCSI disk
[ 10.214408] kjournald starting. Commit interval 5 seconds
[ 10.219984] EXT3-fs (sda7): mounted filesystem with ordered data mode
[ 10.226502] VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
[ 10.234254] Freeing unused kernel memory: 148K (c06fa000 - c071f000)
start rcS
set global environment params
mount proc
remount root file system rw
[ 10.635015] EXT3-fs (sda7): warning: checktime reached, running e2fsck is recommended
[ 10.643281] EXT3-fs (sda7): using internal journal
mount sysfs
start boot log
detect and set platform
isp1
isp1
mount dev/pts
update dev nodes
booting using sda1 file system...
[ 12.341933] kjournald starting. Commit interval 5 seconds
[ 12.347859] EXT3-fs (sda1): using internal journal
[ 12.371790] EXT3-fs (sda1): recovery complete
[ 12.376158] EXT3-fs (sda1): mounted filesystem with ordered data mode
start rcS
set global environment params
mount proc
remount root file system rw
mount sysfs
start boot log
detect and set platform
isp1
isp1
mount dev/pts
update dev nodes
booting using sda1 root file system...
enable IP forwarding...
run udevstart to update dev nodes when necessary
inserting kernel modules:
[ 14.385258] iscsi_trgt: version magic '3.14.2 preempt mod_unload ARMv5 p2v8 ' should be '3.14.2 mod_unload ARMv5 p2v8 '
[ 14.431819] Loading iSCSI transport class v2.0-870.
[ 14.449838] iscsi: registered transport (tcp)
start buttons control daemon
create temporary passwd file
create temporary group file
[ 15.091921] kjournald starting. Commit interval 5 seconds
[ 15.097519] EXT3-fs (sda5): warning: checktime reached, running e2fsck is recommended
[ 15.105683] EXT3-fs (sda5): using internal journal
[ 15.121789] EXT3-fs (sda5): recovery complete
[ 15.126157] EXT3-fs (sda5): mounted filesystem with ordered data mode
Setting up swapspace version 1, size = 526413824 bytes
[ 15.303538] random: mkswap urandom read with 119 bits of entropy available
UUID=14ecc604-5265-416c-b6c7-768fc9199d95
[ 15.373796] Adding 514076k swap on /dev/sda3. Priority:-1 extents:1 across:514076k
set samba environment for version 3.0.37
[ 15.862034] random: nonblocking pool is initialized
mount: /sys/kernel/config: mount point does not exist.
mkdir: can't create directory '/proc/bus/usb': No such file or directory
mount: /proc/bus/usb/: mount point does not exist.
configure loopback network interface
setting reboot and standby
phn adapting motion.conf file
starting php based setup routines step 1
[ 28.794095] udevd (925): /proc/925/oom_adj is deprecated, please use /proc/925/oom_score_adj instead.
[ 28.803503] udev: starting version 130
[ 38.951924] kjournald starting. Commit interval 5 seconds
[ 38.979530] EXT3-fs (sda8): using internal journal
[ 39.001792] EXT3-fs (sda8): recovery complete
[ 39.006158] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 40.832412] mv643xx_eth_port mv643xx_eth_port.0 eth0: link down
[ 40.838781] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 43.823588] mv643xx_eth_port mv643xx_eth_port.0 eth0: link up, 1000 Mb/s, full duplex, flow control disabled
[ 43.834172] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
start rpcbind service
starting php based setup routines step2
starting php based setup routines step3
starting php based setup routines step banner
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
move smbd en nmbd db files away from ram disk to prevent hanging samba server
LED settings
USER=root
OLDPWD=/
HOME=/
RSYNC_RSH='/usr/bin/dbclient -p 22'
TERM=vt102
PATH=/sbin:/bin:/usr/sbin:/usr/bin:/usr/local/bin:/usr/local/sbin:/opt/bin:/opt/sbin
PHILIPS=1
SHELL=/bin/sh
PWD=/
isVM=0
------------------------
rcS finished
------------------------
list boot.log file
start boot log
is a physical machine
detect and set platform
isp1
isp1
UIMAGE-3142-ISP1-1
Current kernel: 3.14.2 #1 Sat May 16 23:32:53 CEST 2015
isp1
isp1
mount dev/pts
update dev nodes
booting using sda1 root file system...
enable IP forwarding...
run udevstart to update dev nodes when necessary
inserting kernel modules:
modprobe: 'iscsi_trgt.ko': invalid module format
start buttons control daemon
device = isp1
source = buttons-nwsp2
buttons-nwsp2 daemon started
Wed Oct 20 15:06:28 CEST 2021
create temporary passwd file
create temporary group file
set samba environment for version 3.0.37
configure loopback network interface
setting reboot and standby
isp1
rebootd-isp1
isp1
standbyd-isp1
phn adapting motion.conf file
starting php based setup routines step 1
* Initialize the volatile db file... [ OK ]
* Starting udevd... [ OK ]
* Finishing restore RAID devices... [ OK ]
* Found database configuration file... [ OK ]
* Updating Disks database... [ OK ]
* Starting mount of volumes...
- Mounting volume Vol-A: [ OK ]
* Finishing mount of volumes... [ OK ]
* Generating Hosts File... [ OK ]
* Configuring System Hostname... [ OK ]
* Configuring LAN interface... [ OK ]
* Initializing Timezone... [ OK ]
* Starting web server... [ OK ]
* Starting mount of internal USB ...
* Finishing mount internal USB ... [ OK ]
* Configuring Disks... [ OK ]
* Configuring Samba... [ OK ]
* Configuring System Users...
Root password: use default password
Set users, linux and samba accounts [ OK ]
* Starting Fvdw-sl Discovery Daemon... [ OK ]
start rpcbind service
starting php based setup routines step 2
* Starting dropbear... [ OK ]
* Kill temporary dropbear... [ OK ]
starting php based setup routines step 3
* Starting daemon update Hosts File... [ OK ]
* Starting mount of remote shares...
* Finishing mount shares... [ OK ]
* Starting NTP client... [ OK ]
starting php based setup routines step banner
*** fvdw-sl NAS firmware
This is fvdw-sl version: fvdw-sl 18.2 patched
built on: October 18 2019
LAN IP address: 10.1.1.7 (static)
Port configuration:
LAN -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
move smbd en nmbd db files away from ram disk to prevent hanging samba server
LED settings
else loop1 finished
rcS finished
------------------------
rcS finished
------------------------
list boot.log file
start boot log
is a physical machine
detect and set platform
isp1
isp1
UIMAGE-3142-ISP1-1
Current kernel: 3.14.2 #1 Sat May 16 23:32:53 CEST 2015
isp1
isp1
mount dev/pts
update dev nodes
booting using sda1 file system...
else loop1 finished
rcS finished
Then I can log into the web console or ssh. Putty show nothing on screen when I run
poweroff command - just window with standard info "Remote side unexpectedly closed network connection".
In serial port window I've got:
- Code: Select all
list boot.log file
start boot log
is a physical machine
detect and set platform
isp1
isp1
UIMAGE-3142-ISP1-1
Current kernel: 3.14.2 #1 Sat May 16 23:32:53 CEST 2015
isp1
isp1
mount dev/pts
update dev nodes
booting using sda1 file system...
else loop1 finished
rcS finished
params.c:OpenConfFile() - Unable to open configuration file "/usr/lib/smb.conf":
No such file or directory
ERROR: Failed to initialise messages database
killall: zfs: no process killed
killall: zxtract: no process killed
killall: zappdms: no process killed
killall: udhcpc: no process killed
killall: syncawayd: no process killed
killall: ntpd: no process killed
killall: fanctld: no process killed
The system is going down NOW!
Sent SIGTERM to all processes
Sent SIGKILL to all processes
Requesting system poweroff
[ 454.531912] sd 1:0:0:0: [sda] Synchronizing SCSI cache
[ 454.571848] sd 1:0:0:0: [sda] Stopping disk
[ 455.172395] reboot: System halted
Then when I disconnect power and connect it back (
without serial port connected) lights turn on and nothing else. But if I connect serial port and do the power reconnection - everything starts as usual.
Second strange behavior: I'm not able to reinstall fvdw. When I turn on FVDW console and click on Action->Install fvdw-sl firmware, select proper kernel (UIMAGE-3136-ISP1-14-standalone) then u-boot console appears and then I turn on NAS but I can wait forever to connection. There is only
waiting for u-boot.. message.
Third thing: even if I was able to update to 18.2 version (thx to @Jocko) I cannot install Transmission server:
Fail: can not retrieve the package, -99Small update: after applying patch fvdw-sl-18.2-patch03-03aug2021 I was able to install Transmission server - thank you @Jocko.