This is the output of my isp1 when booting
- Code: Select all
U-Boot 1.1.1 (Jun 15 2007 - 08:56:23) Marvell version: 1.7.3
| \/ | __ _ _ ____ _____| | |
| |\/| |/ _` | '__\ \ / / _ \ | |
| | | | (_| | | \ V / __/ | |
|_| |_|\__,_|_| \_/ \___|_|_|
_ _ ____ _
| | | | | __ ) ___ ___ | |_
| | | |___| _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
\___/ |____/ \___/ \___/ \__| ** LOADER **
** MARVELL BOARD: DB-88F5182-EDmini-V2 LE
U-Boot 1.1.1 (Sep 3 2008 - 07:36:51) Marvell version: 1.7.3 - LaCie version: 1
DRAM CS[0] base 0x00000000 size 64MB
DRAM Total size 64MB
Flash: flashStructGet manu 0xff id 0xff
[0kB@fff80000] ## Unknown FLASH at fff80000: Size = 0x00000000 = 0 MB
Flash: 0 kB
Addresses 20M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (20M - 16M): Done
*** Warning - bad CRC, using default environment
Soc: MV88F5182 Rev 2
CPU: ARM926 (Rev 0) running @ 400Mhz
SysClock = 200Mhz , TClock = 166Mhz
USB 0: host mode
USB 1: device mode
PCI 0: PCI Express Root Complex Interface
PCI 1: Conventional PCI, speed = 33000000
Net: egiga0 [PRIME]
Hit any key to stop autoboot: 0
Waiting for LUMP (2)
Using egiga0 device
no lump receive; continuing
Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
StartChannel
Device 1: OK
Model: Hitachi HDP725050GLA360 Firm: GM4OA5CA Ser#: GEC5J
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
** Bad partition - 1:9 1:9 **
Loading from IDE device 1, partition 6: Name: hdb6
Type: U-Boot
Image Name: Linux-2.6.12.6-arm1-lacie5b
Created: 2007-04-20 15:44:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1662140 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
## Booting image at 00400000 ...
Image Name: Linux-2.6.12.6-arm1-lacie5b
Created: 2007-04-20 15:44:19 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1662140 Bytes = 1.6 MB
Load Address: 00008000
Entry Point: 00008000
Verifying Checksum ... OK
OK
As you can see until hit any key to stop autoboot the same.
What you should do when having the marvel prompt and a disc (this may be an empty disk) give this command
- Code: Select all
ide reset
this should give output similar to this,
- Code: Select all
Reset IDE:
Marvell Serial ATA Adapter
Intergrated Sata device found
StartChannel
Device 1: OK
Model: Hitachi HDP725050GLA360 Firm: GM4OA5CA Ser#: GEC5J
Type: Hard Disk
Supports 48-bit addressing
Capacity: 476940.0 MB = 465.7 GB (976773168 x 512)
if the disk is not found then it means there is a problem with the sata interface and thethen there is no way to install or run firmware.
If the the disk is found and correct size is determined it should be possible to try to install fvdw-sl firmware either using fvdw-sl console install feature or using manually commands in uboot (marvell>> prompt) and tftp server of the fvdw-sl console