Succeeded with upgrading to fvdw-9-0
The 1st boot attempt went wrong, did power up, hdd was spinning, no beeps, but also no connections. The IS was not visible within my LAN Routing Table.
2nd boot did the job, the IS was accessible, went on configuring....
Did set up DLNA, made an Share, mediastreaming, 6GB of files copied to the IS, mp3 playback, video playback using MediaPlayer, works :-)
Used Reset button, works :-)
Enabled NTFS read/write, works :-)
Enabled NFS, got an mesage: "Warning: start command nfs-utils returned non zero"
As the system indicates it seems to be running, but to be honest I don't know how to test it properly.
Updated the installguide with correct filenames, for example: sda5-lacie-isp
1.tar.gz
Installation Guideline fvdw firmware on a LaCie-IS500 v0.1e.pdf
Oh and last but not least,
As it seemed this was the last time I had to open the enclosure.
I did exchange the original Samsung 500GB HDD, with an Seagate 2TB HDD. :D
So far so good... thnxs for all your effort fvdw
system_info.jpg
Boot.log
- Code: Select all
start boot log
booting using root file system...
run udevstart to update dev nodes when necessary
inserting kernel modules:
configure loopback netwerk interface
starting php based setup routines step 1
* Initial Orion-Nas XML configuration file... [ OK ]
* Configuring Disks... [ OK ]
* Configuring System Users...
Warning: fopen(/etc/rootpasswd): failed to open stream: No such file or directory in /etc/finc/userfunc_users_commit.finc on line 38
[ OK ]
* Starting mount of volumes...
- Mounting volume Default:
[ OK ]
* Finishing mount of volumes... [ OK ]
* Generating Hosts File... [ OK ]
* Configuring System Hostname... [ OK ]
* Configuring Samba... [ OK ]
* Configuring LAN interface... [ OK ]
* Starting udevd... [ OK ]
* Starting web server... [ OK ]
* Initializing Timezone... [ OK ]
* Configuring Samba... [ OK ]
* Starting syncawayd... [ OK ]
* Marvell mediaserver not started...,QOSd... move random to random-blocks and link /dev/random to /dev/urandom
starting php based setup routines step 2
* Starting dropbear... cmd : dropbear -r '/rw_fs/etc/dropbear/dropbear_rsa_host_key' [ OK ]
starting php based setup routines step banner
*** fvdw-sl NAS firmware
This is fvdw-sl version: fvdw-sl 9.0
built on: sept 10 2011
LAN IP address: 192.168.100.101 (DHCP)
Port configuration:
LAN -> eth0
php based setup routines finished
web permission on resolv.conf
set device tuning for dms performance
move smbd en nmbd db files to ramdisk to enable disk spin down
rcS finished
dmesg output
- Code: Select all
login as: root
root@192.168.100.101's password:
/ # dmesg
Linux version 2.6.33.1 (root@linux-fw1) (gcc version 4.2.0 20070413 (prerelease) (CodeSourcery Sourcery G++ Lite 2007q1-21)) #1 PREEMPT Fri Sep 2 22:00:36 CEST 2011
CPU: Feroceon [41069260] revision 0 (ARMv5TEJ), cr=a0053177
CPU: VIVT data cache, VIVT instruction cache
Machine: LaCie Ethernet Disk mini V2
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Clearing invalid memory bank 0KB@0xffffffff
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x00000000
Ignoring unrecognised tag 0x41000403
Memory policy: ECC disabled, Data cache writeback
On node 0 totalpages: 16384
free_area_init_node: node 0, pgdat c03b2144, node_mem_map c03c9000
Normal zone: 128 pages used for memmap
Normal zone: 0 pages reserved
Normal zone: 16256 pages, LIFO batch:3
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
Kernel command line: console=ttyS0,115200 root=/dev/sda7 ro
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 61036KB available (3536K code, 191K data, 112K init, 0K highmem)
SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:64
Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Orion ID: MV88F5182-A2. TCLK=166666667.
edmini_v2: USB device port, flash write and power-off are not yet supported.
bio: create slab <bio-0> at 0
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
Switching to clocksource orion_clocksource
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
PCI: CLS 0 bytes, default 32
NetWinder Floating Point Emulator V0.97 (double precision)
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
msgmni has been set to 119
io scheduler noop registered
io scheduler deadline registered
io scheduler cfq registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 3) is a 16550A
console [ttyS0] enabled
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
sata_mv sata_mv.0: version 1.28
sata_mv sata_mv.0: slots 32 ports 2
scsi0 : sata_mv
scsi1 : sata_mv
ata1: SATA max UDMA/133 irq 29
ata2: SATA max UDMA/133 irq 29
physmap platform flash device: 00080000 at fff80000
physmap-flash.0: Found 1 x16 devices at 0x0 in 8-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
physmap-flash.0: JEDEC Device ID is 0xB9. Assuming broken CFI table.
physmap-flash.0: Swapping erase regions for broken CFI table.
number of CFI chips: 1
RedBoot partition parsing not available
Using physmap partition information
Creating 1 MTD partitions on "physmap-flash.0":
0x000000000000-0x000000080000 : "Full512kb"
MV-643xx 10/100/1000 ethernet driver version 1.4
mv643xx_eth smi: probed
net eth0: port 0 with MAC address 00:d0:4b:86:dd:8e
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
orion-ehci orion-ehci.0: Marvell Orion EHCI
orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1
orion-ehci orion-ehci.0: irq 17, io mem 0xf1050000
orion-ehci orion-ehci.0: USB 2.0 started, EHCI 1.00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
input: gpio-keys as /class/input/input0
i2c /dev entries driver
rtc-rs5c372 0-0032: rs5c372a found, 24hr, driver version 0.6
rtc-rs5c372 0-0032: rtc core: registered rtc-rs5c372 as rtc0
Registered led device: power:blue
usbcore: registered new interface driver usbhid
usbhid: USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
VFP support v0.3: not present
rtc-rs5c372 0-0032: setting system clock to 2011-09-11 00:05:48 UTC (1315699548)
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-8: ST32000542AS, CC34, max UDMA/133
ata2.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
ata2.00: configured for UDMA/133
scsi 1:0:0:0: Direct-Access ATA ST32000542AS CC34 PQ: 0 ANSI: 5
sd 1:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
sd 1:0:0:0: [sda] Write Protect is off
sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 1:0:0:0: [sda] Attached SCSI disk
EXT3-fs (sda7): recovery required on readonly filesystem
EXT3-fs (sda7): write access will be enabled during recovery
EXT3-fs (sda7): recovery complete
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda7): mounted filesystem with ordered data mode
VFS: Mounted root (ext3 filesystem) readonly on device 8:7.
Freeing init memory: 112K
EXT3-fs (sda7): warning: maximal mount count reached, running e2fsck is recommended
EXT3-fs (sda7): using internal journal
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda5): using internal journal
EXT3-fs (sda5): recovery complete
EXT3-fs (sda5): mounted filesystem with ordered data mode
Adding 257032k swap on /dev/sda3. Priority:-1 extents:1 across:257032k
Slow work thread pool: Starting up
Slow work thread pool: Ready
NTFS driver 2.1.29 [Flags: R/W MODULE].
fuse init (API version 7.13)
kjournald starting. Commit interval 5 seconds
EXT3-fs (sda8): using internal journal
EXT3-fs (sda8): recovery complete
EXT3-fs (sda8): mounted filesystem with ordered data mode
eth0: link up, 1000 Mb/s, full duplex, flow control disabled
You do not have the required permissions to view the files attached to this post.